Type: Airsoft Blowback AEG.

Manufacturer:Bolt Airsoft.

Model: M16A4 with Heavy BRRS (Bolt Recoil Shock System).

Materials: Metal & Nylon.

Weight: 7.7 pounds (3500 grams).

Length: 43 inches (1100mm).

Propulsion: AEG with Heavy BRSS

Action: Semi/full auto, single action.

Ammunition Type: 6mm Plastic Airsoft BB (recommend using undersized BB's).

Ammunition Capacity: 300+ round magazine.

FPS: 360+.

Trigger Pull: The trigger pull on the BOLT Airsoft M16A4 is fairly short and light as it is essentially just an on off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course in full auto when full auto position is selected. As is with all AEG rifles there is a bit of a delay while the spring is retracted and released, this is not as noticeable in full auto mode and also when using higher voltage 11.1 volt batteries.

Accuracy: I tested the BOLT M16A4 BRSS Airsoft rifle first on my Chronograph to see what kind of real world fps I would get from it using .20 gram Airsfot BB's. The BOLT M16A4 produced consistent 350 fps shots which is perfect for indoor or outdoor Airsoft events. I then stepped back roughly 30 feet and place 10 rounds on my paper target using a semi rested position and was able to get a nice tight 2 inch grouping. When switching up to full auto mode the grouping pretty much stayed exactly the same, right in that 2 inch pocket.

Build Quality: The Bolt M16A4 AEG Blowback Airsoft Rifle is very well made with a full Metal upper and lower receiver, along with metal and polymer parts exactly where they would be on the real steel version of an actual M16 or AR styled riffle. The only rubber or nylon components are the stock and the grips and perhaps some internal parts. I really could not find anything to complain about other than making sure to use the right sized ammo as the barrel is a true 6mm barrel and so when using actual 6mm BB's they can get jammed up. I had great results when I used 5.95mm Airsfot BB's.

Realism: As with many Airsoft guns, there is great attention to realism and the Bolt Airsoft BRSS M16A4 AEG is another great example of an Airsoft rifle based on the Colt M4 platform. It is an AEG but because of the Heavy BRSS (Bolt Recoil Shock System) you get a very nice compromise between a conventional AEG and a GBB (Gas Blow Back Airsoft) gun. In other words, like a standard AEG I get that endless stream of consistent BB's flying down range on target but unlike a true Gas Blow Back Airsoft gun, I don't get that drop off in power and limitation to about 30 usable rounds per magazine. What I do get similar to a GBB is that recoil action that helps make the shooting experience so much more believable! Even the sound from the Bolt M16A4 is much snapper than a standard AEG and more like a GBB. I also like the fact that the charging handle and forward assist work similarly to a real AR and also the dust cover cleverly exposes the bolt and internal hop-up for easy adjustment along with the bolt cycling just like a GBB rifle would cycle which is similar to a real steel AR.

Pros:

• AEG Performance with GBB like Recoil.

• Very high quality materials and workmanship throughout.

• Lots of forward rails to place accessories on and just looks cool in general.

• The fixed classic M16 stock is very comfortable and grows on you over time.

• Can shorten the gun by removing the barrel extension if you like.

• Can use 11.1V Li-Po or 9.6V Ni-mh or Ni-Cd batteries.

• Fully Adjustable Hop-up.

• Semi and Full Auto.

Cons:

• BRSS system will drain the batteries faster than a standard AEG.

• Can not switch out the stock as the BRSS system extends back into it.

• Need to use undersized 6mm Airsoft BB’s because of the tight barrel.

Comments:

The BOLT M16A4 AEG Blowback Airsoft Rifle with BRSS Recoil is a great compromise for the avid Airsofter looking for a practical skirmish weapon, but also craving the realistic experience of having blowback with recoil similar to a Gas Blow Back systems. I really like this concept and find it great fun to shoot even if its just for plinking in the yard. The overall quality is very excellent and you just have to love the AR platform it's based on. If you're into customizing you can mix and match many external and internal parts with other existing Airsoft mechanical parts and I would imagine real steel accessories. It's great to be able to use an Airsoft rifle in virtually any weather condition and still get that Gas Blowback Feel but with AEG performance and consistency.

My Vimeo Video Review for the Bolt M16A4 AEG Blowback Airsoft Rifle with BRSS Recoil:

Buy Airsoft Rifles in the Canada Store

Buy Airsoft Rifles in the US Store

My first impressions with the Bolt M16A4 AEG Blowback Airsoft Rifle where not so good as it was miss feeding and miss firing terribly for me. A quick communication with BOLT Airsoft and I was informed that perhpas my BB choice was the wrong one. The Bolt M16A4 AEG Blowback Airsoft Rifle has a true 6mm barrel so it is a tight fit with BB's that are 6mm since many can actually be a bit larger making them get stuck in the breach area.

BOLT Airsoft suggested I switch my Airsfot BB choice to a slightly under sized 6mm Airsfot BB so I tried some of my 5.95mm Airsoft BB's and all I can say is it was like shooting a different gun. Not only did it feed and shoot perfectly, but the Bolt M16A4 AEG Blowback Airsoft Rifle with Heavy BRSS Recoil also became instantly more accurate for me. The moral of this story is always make sure to use the right ammo in your gun :)

So getting back to my Field Test Shooting Review for the Bolt M16A4 AEG Blowback Airsoft Rifle with BRSS Heavy Recoil... In this video Field Test Review I shoot several rounds through my Chronograph to test out the fps velocity of the Bolt M16A4 AEG Blowback Airsoft Rifle. Which by the way came in around the mid 300's. I also step back 30 feet and shoot some semi auto rounds into a paper target to see how accurate the Bolt M16A4 AEG Blowback Airsoft Rifle is. Since the Bolt M16A4 AEG Blowback Airsoft Rifle is a semi and full auto AEG Airsoft rifle, I also had to replicate my accuracy in full auto to see if my groupings would stay consistent even at a high rate of fire. I was very impressed with the accuracy in both semi and full auto, form 30 feet out you will get within 2 inches all day long.

It is fair to note that I was using 11.1 volt Li-po batteries with .20 gram BB's for the entire testing so this did effect my motor speed giving me quicker trigger response and faster full auto rate of fire. I would suggest using a high capacity battery setup since the BRSS Heavy Recoil does use up some additional battery power but boy is it worth it. The BRSS Recoil is not going to be as heavy as a true gas blowback system but it is close and does give you a nice shoulder tap but with the benefit of high capacity AEG magazines and consistent AEG performance.

In a nutshell, if you want the dependability, consistency and none stop shooting performance of an AEG Airsoft AM16 but with the blowback action of a gas system then make sure to give the Bolt M16A4 AEG Blowback Airsoft Rifle with BRSS Heavy Recoil a good look into.

A while back, BOLT was kind enough to send me one of their B.R.S.S. Recoil AEG Airsoft Rifles for review, make sure to watch my full review of the BOLT B4A1 BRSS Recoil Blowback AEG Airsoft Rifle.

Well again BOLT came through and sent me their latest offering, the BOLT AEG M16A4 Blowback Airsoft Rifle with B.R.S.S. Heavy Recoil system. B.R.S.S. stands for BOLT Recoil Shock System. The new BOLT Heavy Recoil system has a fixed stock which houses the improved recoil unit giving a more direct and solid recoil effect to the users shoulder. The BOLT M16A4 is a long length AEG Blowback Airsoft Rifle also suitable for snipers.

Here are some of the specifications:

• Blowback B.R.R.S Heavy

• Adjustable Hop-up

• Semi & Full Auto

• Standard AR 70 & 300 round magazines

• 312 fps & 393 fps versions

• Aluminum, ABS, Nylon & Glass Fiber and Steel construction.

• 7.4V & 11.1V (Li-Po) or 9.6V (Ni-mh / Ni-Cd)

• 7.7 pounds (3500 grams)

• 43 inches long (1100mm)

• Comes in Black / Tan

In this YouTube Preview video for the BOLT M16A4 AEG Blowback Airsoft Rifle I show you around the gun a bit and do a quick shooting test. Unfortunately I was using 6mm Airsoft BB's which I later found out where a bit to large in diameter since the BOLT M16A4 AEG Blowback Airsoft Rifle has a true 6mm barrel. After the video when I received this information from BOLT I switched to 5.95mm Airsoft BB's and the BOLT M16A4 AEG Blowback Airsoft Rifle worked perfectly for me :)

Stay tuned for my Full Table Top and Field Test Shooting videos for the BOLT M16A4 AEG Blowback Airsoft Rifle:

In this preview Update Vimeo Video I take a quick look at the following ASG Airsoft and BB Guns...

ASG Marsushin Deringer Chrome Gas Airsoft Pistol:

• Ammo Capacity: 2

• Green Gas

• Weight: 215 gram (.5 pounds)

• Power: 77 m/s (252 fps)

• Plastic Frame / Metal Grips

ASG MK2 Dual Tone CO2 Airsoft Pistol:

• Ammo Capacity: 15

• 12 Gram CO2

• Weight: 790 gram (1.8 pounds)

• Power: 127 m/s (417 fps)

• Metal and Plastic

ASG CZ 75 CO2 Blowback BB Pistol:

• Ammo Capacity: 17

• 12 Gram CO2

• Weight: 950 gram (2.1 pounds)

• Power: 95 m/s (312 fps)

• Mostly Metal

ASG US Marine MEU Limited 1911 Gas Blowback Pistol:

• Ammo Capacity: 15

• Gas Blowback

• Weight: 1020 gram (2.3 pounds)

• Power: 86 m/s (283 fps)

• Mostly Metal

ASG CZ Scorpion VZ61 AEG Airsoft Machine Pistol:

• Ammo Capacity: 58

• Electric AEG

• Weight: 1220 gram (2.7 pounds)

• Power: 81 m/s (266 fps)

• Metal and Plastic

ASG BT5 PDW AEG Aisoft Rifle:

• Ammo Capacity: 100

• Electric AEG

• Weight: 2400 gram (5.3 pounds)

• Power: 95 m/s (310 fps)

• Metal and Plastic

ASG Franchi SAS 12 Pump Action Airsoft Shotgun:

• Ammo Capacity: 30 (3 Shot Burst)

• Spring Pump

• Weight: 1200 gram (2.7 pounds)

• Power: 85 m/s (279 fps)

• Metal and Plastic

Buy ASG MK2 Dual Tone CO2 Airsoft Pistol in Canada

Buy ASG BT5 PDW AEG Aisoft Rifle in Canada

Buy ASG US Marine MEU Limited 1911 Gas Blowback Pistol in Canada

Buy ASG CZ 75 CO2 Blowback BB Pistol in Canada

Buy ASG CZ 75 CO2 Blowback BB Pistol in the US

Buy ASG CZ Scorpion VZ61 AEG Airsoft Machine Pistol in Canada

Buy ASG CZ Scorpion VZ61 AEG Airsoft Machine Pistol in the US

Some of you have been waiting on back orders and to also make new orders of ASG products, we just received an ASG order so many ASG items are now back in stock! Any back orders will be taken care of first and then new orders will be processed, as always, stock is limited especially on certain items so act fast!

Here is my official Mobster Halloween Costume Video as promised and it looks like I made it just in time for Halloween!

There have only been a few entries so far so come on everyone, let's get your costume videos uploaded and entered into this years 2014 Halloween Costume Giveaway Contest for a chance to win a KWC / Cybergun Blowback Pistol.

You still have till the 10th of November but time is running out...

If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

Buy KWC Airsoft Desert Eagle in Canada

Buy KWC Silver Desert Eagle in Canada 

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

2. Can I reuse a C2 once it is empty?

3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two:

This may be a bit controversial for some people who don't like the thought of using an gun for hunting or extermination of unwanted pests. But weather or not it is accepted by all, it is a practice that many people still embrace including myself when done in a humane way.

Let's start off by addressing this topic by asking some questions and filling in some of the answers. Keep in mind I go into much more detail in my Vimeo video below.

What is the reason that you need to Shoot or Hunt an Animal?

Are you shooting an animal out of need or just for fun, sure there is a thrill in the sport of hunting but after taking down your prey, the animal should not be killed in vain as the meat should be eaten. There are also times when pesky critters get into your gardens, tree farms, feeding stations garbages and who knows what else? I personally think shooting an animal that has not done you any harm or that you don't plan on eating is not ethical. So question your motives wisely?

Can you use an Airgun for Hunting and or Pest Control?

The short answer is yes! As long as you choose the correct Airgun for the job, one that has enough power and accuracy to get the job done in a humane manner. Using an underpowered or inaccurate gun of any type for the chosen target will lead to the animal being wounded and possibly getting away to suffer unnecessarily.

What about Pistols versus Rifles?

Given the choice, a rifle will always be your best bet, rifles tend to be more accurate since they are more stable to hold and the fact that the sights are further apart which improves the guns accuracy. Most rifles also allow for enhanced sighting systems like red dots or magnified scopes for even further accuracy improvements. There are some pistols made specifically for hunting and target shooting that can be accurate but I would limit their use to shorter ranges.

What about Pellet guns versus BB guns?

BB guns in general are not meant for hunting or pest control, and in most cases they are underpowered and not as accurate as their pellet shooting counterparts, especially out at longer ranges where most pests keep their distances to. If you plan on doing some hunting and or pest control, please invest in an adequate pellet rifle to get the job done humanly.

What type of Ammo is best for Hunting and Pest Control?

There are lots of types of pellets available, pointed, rounded, flat, hollow-point and even pellets that have nylon tips. At the end of the day, use the pellet that is the most accurate in your Airgun because shot placement will win over pellet shape any day of the week. The reality is that as long as that pellet hits the target with adequate velocity, it doesn't matter what shape it is, it's more than likely going to pass right through the animal.

What is the lowest FPS that I can use?

I would rather ask the question, what is the highest fps I can get away with since more fps will give you more margin for error, since it will have a flatter trajectory and will do more damage even if your shot is off a bit. An experienced shooter could make a kill shot on a small pest even with a 400 fps airgun but the shot would have to be perfect and the range would have to be close. Of course when shooting larger game, you will need larger caliber pellets with higher velocities. Also when using a high velocity airgun you need to consider what is beyond your target, if you miss, where is that pellet or bullet going to end up? You need to make sure you do not injure anyone by mistake as pellets/bullets can travel a long distance.

How large of an Animal can an Airguns Kill?

This is really dependent on the Airgun being used, Airguns come in many different calibers, from .177 right up to .50 caliber, some PCP Airguns can even take down a deer! You need to do your research and make sure the Airgun you choose has both the power and accuracy you need for the intend prey.

Where can I use an Airgun for Hunting and or Pest Control?

This is a question you need to ask your local authorities as laws and hunting regulations are different just about everywhere. Even shooting pests on your property may require a permit so be careful to obey your local laws.

In many of my reviews I show the loading process of each gun but sometimes I either skim over this part or assume most people already know how to load an Air Pistol and skip it entirely. Well as it turns out not everybody does know how to load up an Airgun or they are unclear on certain areas, like do you actually need the CO2 and how long can you leave CO2 in an airgun?

So I made a video specifically to cover how to load CO2, BB's and/or Pellets into your Air Pistol.

Now even though this video is targeted at 4.5mm Steel BB and Lead Pellet Pistols, there is a crossover with 6mm Airsoft Pistols so this video may also help an Airsoft shooter.

Our Family Bearded Dragon (Dijon) was looking rather sad and lonely today so I figured he could hang out while I made the video, he really doesn't do much of anything most of the time so why not give him a special appearance in one of the Replica Airguns Videos ;)

Two questions that come up over and over again and to be honest I just hate answering, mainly because both of these questions to me are kind of common sense questions. I feel if someone where to stop and actually think about teh question, the answers would become obvious.

That said, common sense has to be learned somewhere and not all of us are exposed to the same life experiences so here goes...

The two questions are:

• Will this Ammunition Work in my Gun?

• Can I Convert a Blank Gun to a Real Gun?

The answer for both of these question is actually the same! Use the ammo made for your gun and do not try to use anything other than the ammo that was made for your gun. Do not try to modify your gun to shoot anything other than the ammo that was made for it, if you do, you may be breaking the law and could land yourself in jail. If you can follow these rules then your ammo and gun will work as intended :)

So that's pretty much it in a nutshell, watch my YouTube video below as I show you examples of ammo types with visuals on exactly why you need to use the ammo made for your gun. I also talk about the dangers of attempting to modify a blank gun to shoot some sort of real bullet and why it is a very bad idea in so many ways to try and convert a blank gun into a real gun.

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the Canada Store

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the US Store

This video should go "Hand in Hand" (pun intended) with my Best Two Handed Pistol Grip Tutorial Video that I did last year back in August. After that video I had several people ask me to talk about how to aim a gun. I guess if you have been shooting guns for a while you kind of take it all for granted but after teaching my kids the proper way to aim a gun at a target, this info is not naturally born into us ;)

This video demonstrate how and where to place your open gun sights on a target and also how you can compensate for a gun that may not be perfectly sighted in.

This is take 2 of my Modification to my F1 Chrony Chronograph. The purpose of this modification is to improve the low light FPS readings. In my first attempt I used LED Puck Lights but they where the kind that used flat panel LED's and they only had 4 panels per LED Puck which made each LED panel kind of bright. I did get OK with my first mod using LED Puck Lights but not as good as I would like to see.

So here we are with take 2 of F1 Chrony Chronograph LED Puck Light modification and this time around I am using standard bulb styled LED lights and to improve my chances of this working I went with and LED Puck that contained 24 LED bulb lights per puck, this way each light on it's own is a bit dimmer which I feel will give a more diffused lighting effect and hopeful consistent fps readings.

By the way I got these LED Puck Lights at my local dollar store for $2.50 each so not a very expensive modification, especially if they work.

Well... Watch the video and see how they perform...

This video was made to show you the results I got by mounting LED puck lights to the top of my F1 Chrony Chronograph defuser panel in order to improve the low light Feet Per Second readings when using 4.5mm Steel BB's.

I have been struggling with my F1 Chrony Chronograph during the fall and winter months as tit becomes overcast and dark where I live. There have been days where I have gone out to shoot my field test shooting video and not been able to get any Chronograph fps results which is very frustrating because much time and effort goes into the planning setup of each video.

I was given advice from several of my viewers to mount an LED puck style light on the back side of my Chronograph defuser panel and that this helps the Chronograph to read much better in low light situations.

I bought a multipack of the LED puck lights from my local Costco but they did not work as well as I expected them to as they had a panel style of LED rather than the bulb shaped LED which I think may diffuse the light a bit more. My next experiments will be done using LED Puck lights but with the bulb styled LED.

You can watch my video to see how my first attempt using an LED Puck light with my F1 Chrony Chronograph worked out.

I stopped by the ICS Booth, we don't sell too much of their products but have carried a few items from time to time. ICS caries some nice quality Airsoft guns including the M1 Grand with real wood stock, and some AK & AR variants.

One of our suppliers had the new FN Herstal Five-seveN Blowback Airsoft pistol, I believe made by Marushin. Like the real FN Herstal Five-seveN, the pistol is pretty much all polymer including the slide and frame. This pistol also uses CO2 in the full size drop out magazine which should make it fairly powerful.

Looks like there is another Dan Wesson contender available now in the form of a Swiss Arms S&W 357 Magnum 4 inch and 6 inch barreled version, they look really nice and like the Dan Wesson have the realistic reusable brass shells that hold the 4.5mm Steel BB's.

Ever considered owning a  mobile Gunsmith vehicle, look no further, I came across this pimped out Firearms Van complete with machine guns mounted in the front :) Inside was a complete firearms workshop.

Last but not least, we had some fun while in Vegas. I go down for the SHOT Show for business but I also bring my wife and we make time for some non business related activities. I generally stay at the WorldMark resort each time and this year the weather was pretty nice so we where able to get some sun by the pool a couple of days and I even got a tan line! Of course the food and entertainment is always awesome in Vegas.

We carry a lot of the G&G line and perhaps have as much in stock as you would find at the G& G booth ;) I did see a few items we do not have in stock so I will have to see what I can do about that. Some products that I hope to see added to our Canada Replica Airguns Store would for sure be the M1 Grand and our Canadian Military Colt C7A1/2.

I also visited my friends at the ASG booth but for some reason I did not get a photo  of their booth? I do have some video walk through stuff I will show you in my YouTube Video coverage of this years Vegas SHOT Show. Most importantly I have lots of gun photos so let's take a look at them...

One of my favorite ASG pistols is the Bersa BP9CC, I have already reviewed it and I just really like how this gun looks and holds, ASG took it one step further this year by adding a two-tone silver version and I have to say it looks awesome in person, my photos do not do it justice at all :(

A new handgun to the ASG blowback pistol series is the CZ P-09 Duty Pellet pistol. Basically it shares similar mechanics to the Umarex PX4 and Gamo PT-85 using the double sided rotary pellet magazine with 8 shots located on each end of the stick magazine. The ASG CZ P-09 Duty features a metal slide, working hammer and safety.

Another pellets pistol that should be very familiar to most of you is the new .177 caliber pellet shooting Dan Wesson in 6 inch silver and 8 inch black versions. ASG added a rifled barrel and redesigned solid brass shells that hold pellets instead of 4.5mm Steel BB's. Expect to take a little bit longer to reload the pellets as unscrewing the tip of each shell is required to place a .177 caliber pellet in each bullet tip.

Of course ASG has tons of licensed pistols to choose from, many on both 4.5mm Steel BB and 6mm Plastic Airsoft!

One new rifle that stood out to me was the ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle, the Scorpion features an intelligent AEG system that detects when there may be a potential feeding problem and also when the magazine is out of ammo.

Type: Airsoft.

Manufacturer:King Arms.

Model:Thompson M1A1 Military & M1928 Chicago (Gold & Chrome).

Materials: Metal & Wood.

Weight: 6.6 pounds.

Barrel: 15 inches, metal.

Propulsion: AEG

Action: Semi/full auto, single action.

Ammunition Type: 6mm Plastic BB (recommended .20 gram plus).

Ammunition Capacity: 420 round magazine.

FPS: 380-410.

Trigger Pull: The trigger pull on the King Arms Thompson Machine Guns is fairly short and light as it is essentially just an on-off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course even quicker when full auto is selected. As with all AEG systems their is a slight delay between when you pull the trigger and the shot is taken as the internal spring needs to compress first before releasing.

Accuracy: In many cases Airsoft guns can be just as accurate as 4.5mm BB guns, well at least at fairly close ranges, I was able to get most of my .25 gram BB 10 round target test shots within 1 inch from 30 feet away using a semi-rested position. There where a couple BB's that lengthened the group out to about 2 inches but still a very good result when you consider these are plastic BB's being used. In Terms of FPS, I did stick with the slightly heavier 2.5 gram Airsoft BB's and still got a decent 360 average 5 shot Chronograph test result making this AEG Airsoft rifle perfect for just about any Airsoft game type.

• Click here to watch my Field Test Shooting Video for these King Arms Thompson Machine Guns

Build Quality: The King Arms 23 Karat Gold and Chrome Platted AEG Thompson Machine Guns are very well made using Aluminum Zinc Alloy bodies and real Wood Stocks, the fit and finish is very good and pretty much everything on these rifles are either metal or wood. You will have to polish these guns with a cloth from time to time since the mirror finish shows every smudge and finger print.

Realism: I'm not sure how many real 23 Karat Gold and Chrome Platted Thompson Machine Guns there are out there but there has to be at least a few ;) But going on how these guns look and feel, they are solid and very realistic. Some people have mentioned that the bolt should be on the top for some versions of the Thompson's but there are some Thompson's with the bolt on the side so I suppose we will let that one slide. The Wood stocks are a real plus adding to the overall weight and authenticity. Most parts works as they would on the real steel Thompson M1A1 Military or M1928 Chicago (Gold or Chrome) AEG Airsoft Machine Guns.

Available in the: The Canada Replica Airguns Store.

Pros:

• Gorgeous Wood stock and Gold or Chrome platting.

• Nice high capacity metal magazines, can be mixed and matched.

• Adjustable rear sight for windage with two sight positions (Notch & Peep).

• Semi and full auto selectable with really nice rate of fire.

• FPS is bang on for indoor or outdoor Airsoft games.

• Fully Thompson licensed.

• Comes with Certificate of Authenticity.

Cons:

• Does not come with a battery or charger.

• Prone to finger prints and smudges.

• Need to use a screw driver to get at the battery.

Comments:

I am a big fan of the King Arms Thompson line, even the all black version with the plastic stocks looks and functions great. Internally the lower cost black version is the same and having previously shot my black Thompson, I knew these blinged out 23 Karat Gold and Chrome Platted versions where also going to perform as good as they looked! I'm not so sure about buying a Gold or Chrome Thompson for everyday use, since they will get knocked around and scratched up but if you are looking for the best of the best with real wood stocks and all metal parts then make sure to consider one of the Thompson 

My Vimeo Video Review for the King Arms Thompson Gold & Silver AEG Airsoft Machine Guns:

Buy the King Arms Thompson Special Gold & Chrome AEG Rifles in Canada

We just received an order of KWC products so if you've been waiting for some out of stock items then go take a look! By the way, the KWC Beretta / Taurus full metal blowback BB and Airsoft versions now come semi and full auto enabled!

Canada Replica Airguns Store  -  US Replica Airguns Store