Propulsion: Green gas or 12 Gram CO2 dependant on magazine used.
Action: Blowback,Single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 29 rounds.
FPS: 410-440 fps
Trigger Pull: The trigger pull on the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is pretty much exactly like a real Ruger 10/22, nice and short, not to light or heavy, crisp and single action only. If you already have a Ruger 10/22 and want to pickup this Airsoft version for some anytime shooting then you will not be disappointed in the trigger since it is already what you are used to.
Accuracy: I decided to setup my paper target a little further out than my standard 30 feet, so I took it back to around 50 feet and put around 24 shots into it in a fairly quick succession from a rested position. The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine grouped continently and well centred on target getting around a 3 inch grouping. This was using a red dot scope but with the out of the box hop-up setting in place. I was a little bit surprised by my fps results as my Chronograph recorded an impressive 445 average 5 shot fps using the lower powered green gas magazine. All shot where within only a few fps of each other too! I can only imagine how hard this gun would shoot using the alternative CO2 Magazine. Blowback action was just enough to give some feedback and of course allowed for the bolt to cycle giving the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine a true single action trigger pull.
Build Quality: The build quality for all KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is very good with a nice weight and feel to it, It really does feel like I am holding a real Ruger 10/22 and it is one of the most popular semi auto 22LR rifles out there for a reason. Mechanically this Ryger 10/22 copy works great, super consistent and very responsive. The fit and finish as with all KJWorks guns is top notch.
Realism: The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is for all intents and purposes simple an Airsoft version of the Ruger 10/22 and even though I have no way to confirm this, I would imagine many 10/22 after market accessories may actually work with the KJWork 10/22 Gas Blowback Airsoft Carbine. Everything works just like it would on a real 10/22 without the loud noise and ejecting shells.
Built on the very popular 10/22 platform so lots of people are going to be very familiar with this rifle and may want an Airsoft version they can shoot just about any time they feel like it.
Good weight and feel to it.
Blowback semi auto action with true single action trigger.
Lots of rail access points for tons of add on accessories.
Pop-up fully adjustable sights stay out of the way but are ready to go when needed.
Easy to adjust Hop-up.
Available magazines in both CO2 and Green Gas.
Adjustable AR styled rear stock with AR pistol grips.
Sling mounts included.
Works with standard Airsoft screw on flash hider or suppressors.
Awesome FPS and consistency.
Very accurate even at 50 feet, around a 3 inch 25 shot grouping.
Cons:
No full auto mode.
Higher capacity mag would have been nice.
Would be nice to have a higher capacity magazine for it.
Comments:
I am really impressed with the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine! It feel and shoots a lot like the real steel version but with less noise and recoil. For back yard shooting fun and practice you can not find a cheaper gun out there to simulate shooting your real 10/22 and of course this rifle used on an Airsoft field would be a perfect fir for almost any shooting environment since it is light, compact, accurate and powerful. I think I found my newest favorite Blowback Airsoft Rifle :)
My Vimeo Table Top Review of the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine:
I try and make it to my local gun show which is held in Chilliwack BC about this time each year. It is put on by the Historical Arms Collectors Society of BC and there are generally a lot of used long guns (rifles) some pistols, lots of accessories, knives, hunting gear, knick·knacks and even some antique items. I tend to be looking for airguns or blank guns that are rare or a good deal.
This year I came across a few items that caught my eye. The first item was a Daisy replica 4.5mm BB pistol, I am not a big fan of Daisy replica gun in general as they are usually a far cry from the originals but this Daisy Powerline Model 400 was actually a really good copy of a Desert Eagle in size and looks. Sure it had a lot of plastic in it but it was made in Japan and even being around 20 years olds was holding up really well. This Daisy Powerline 400 even had Blowback which back then was not all that common.
The Daisy Powerline 400 BB Desert Eagle has a 20 round removable magazine that fits along the top of the barrel and it has a claimed fps. It is almost all high grade plastic with the exception of the single action only trigger, safety, hammer, barrel and several internal parts.
The next interesting item I found was a little compact 8mm blank shooter originally made in West Germany. So this blank gun is close to 30 years old. The SM Model 110 8mm Blank Pistol kind of reminds me of my EKOL Tuna in terms of size and functionality since both have the same half slide and magazine release system.
The SM Mod 110 8mm Blank Pistol is front venting and pretty much all metal with reinforced steel areas, it has a 5 round single stack magazine and shoots in single action only.
My last purchase for this show was a new item, here in Canada we generally are not allowed much in the way of items specifically labeled for self defense. There are some work arounds for instance we can carry a knife as long as it is not concealed entirely and we only intend to use it as a tool. We can also carry pepper spray again only for use on animals. Generally speaking we have not been allowed stun guns or tasers here in Canada and even importing them can land you in a lot of trouble! Again it seems a work around has been made, as long as the Stun Gun or Taser is at least 480mm in length then it is not considered a concealable weapon and as long as you have it out on display and only intend to use it on animals that may be a threat to you then all is good :)
The Stun Gun I purchased is basically a baton with a flashlight on the front and a 1 million volt taser on the front of it. You have several options with this device if harm is eminent. You can try blinding the threat with the built in flashlight which is not all that powerful but good for finding your way in dark areas, you can give the attacker a whack with the baton baseball bat style and if none of that is working well let em have the 1 million volt sandwich! We should be getting some of these Stun Baton Flashlights in our Canada Replica Airguns Store at some point so stay posted for that item.
Some more of my Personal airgun pistols for sale! I am showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I am making for the purpose of selling some guns out of my personal collection. I simply have to make room for the new guns I will be testing and reviewing for everyone, my collection has gotten a little bit out of hand and needs to be thinned down a bit :)
In this 6th Mike's Personal Guns For Sale video, I am offering three of my Airsoft pistols, the super popular Dan Wesson 6 Inch Silver in pretty much brand new condition complete with the box, manual, speed loader and shells. I also have tow rather hard to get Airsoft guns that are in somewhat limited working condition and need a little TLC. But the simple fact that they are not easily obtained here in Canada does bring up their value a little bit.
Make sure to watch my above YouTube video to see these Airsoft Pistols I am selling and instructions on how you can take part in the sale and purchase of them. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Here is a list of the Airsoft Pistols I am selling from my personal gun collection:
I will be showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I will be making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing.
To start this series off my first video is to highlight the blank guns I am selling, there are only 4 of them, all of which are really hard to get here in Canada so I am not going to let them go cheap. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.
Make sure to watch my above YouTube video to see the blank guns I am selling and instructions on how you can take part in the sale and purchase of them.
Here is a list of the blank guns I am selling from my personal gun collection:
When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.
Do’s:
Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?
Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.
Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.
Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!
Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.
Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.
Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!
Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.
Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.
Don’ts:
Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.
Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.
Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.
Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.
Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.
Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.
Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.
Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!
Can I use Airsoft BB's in my BB Pistol? I would have to say this is by far the number one question I get asked in the comments section of my Vimeo videos. I have made several videos where this question gets addressed within the video but so far to date I have not made a stand alone video just covering Airsoft BB use in BB Guns.
So here it is, and now I have a video I can link to this so very common question, if you where wondering about this yourself than please watch my YouTube Video on this topic as it goes into a fair amount of detail about it.
The short answer to this question is no, you can not use 6mm Airsoft BB's in a 4.5mm Steel BB Pistol or Rifle. For the simple reason that 6mm is larger than 4.5mm and so the physical diameter of a6mm Plastic Airsoft BB is just to large to fit inside of a 4.5mm Steel BB magazine or barrel.
People have commented about using a 4.5mm plastic Airsoft BB in a 4.5mm BB gun and yes this could in theory be an option but I discuss why I feel this is not a good idea based on size and mass.
I'm getting close to uploading 600 videos now over on the Replica Airguns Vimeo channel, so there are bound to be a lot of similar questions and popular discussions. In this Replica Airguns Vimeo Video I address what I feel are my Top 10 Most Common Airgun Questions and Discussions.
Ammunition Capacity: 15 round full size metal magazine.
FPS: 300+
Trigger Pull: The trigger pull on the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is I would have to say one of the nicest 1911 single action triggers I have tested so far. The take-up is very slight with an extremely light trigger pull required to release the hammer. Any lighter and I would say it would be too light and perhaps prone to accidental firing.The three hole tactical trigger extends out a little further than some 1911's but feels secure on the finger.
Accuracy: At this point I have not shot the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol but have high expectations based on the overall quality of this pistol and form other reviews I have read on this Airsoft 1911 replica. According to the manufacturers claimed fps, we should get somewhere right around 300 fps. The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol has an adjustable rear sight for windage and we can take care of elevation using the adjustable hop-up so zoning in the Socom Gear US Marine MEU SOC 1911 to shoot dead center on target should not be too difficult.
Build Quality: The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is one of those Airguns that really catches your eye, and once you pick it up and hold it in your hands you discover that not only does it look really great but it also feels really great in your hands! The tolerances of the parts are excellent, everything mechanical is smooth without any friction and you can even see the texture of the metal grain through the quality matt black powder finish.
Realism: The ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is a a fantastic replica of a real steel MEU SOC 1911 used by the US Marine Corps' Marine Expeditionary Unit (MEU). The balance and weight really make this 1911 Airsoft pistol feel like your holding the real deal, all the mechanic parts function as they would compared to the original and the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol is fully field stripable.
Excellent quality, durable black powder coat matte finish .
Enhanced Pro-Grip with brass marine inserts
MEU SOC 1911 Licensed.
Three hole tactical trigger with skeleton hammer.
Comes in a hard shell case with Gemtech Outback II 5-inch silencer and lanyard.
Rail for adding accessories.
Cons:
FPS is kind of low for Canada Market so not one we can regularly get in stock.
A bit on the pricy side.
No option of CO2 magazine.
Comments:
With all the BB and Airsoft 1911's out there what makes the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol stand out from the rest. First off it feel the most believabel when holding it in your hand, it seems ot have that perfect weight and balance that is often hard to replicate in an Airgun. With features like enhanced Pro-Grips with brass marine inserts, MEU SOC 1911 licensing, three hole tactical trigger, ambidextrous safety, super smooth and light single action trigger, White dot adjustable sights and the included hard shell case with lanyard and Gemtech silencer you can not go wrong with the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol.
My Vimeo Video Review for the ASG Socom Gear US Marine MEU SOC 1911 GBB Airsoft Pistol:
During this Field Test Shooting Review Video I test out the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol by shooting some rounds through the Chronograph to get an idea on how powerful it really is. I also step back 30 feet and place some rounds down range on my paper target to see just how accurate this little surprise double shot Airsoft pistol is.
In terms of power, all I had to go on was the factory claimed power rating of .6 joules. So I filled up the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol with Propane gas, loaded two .20 gram BB's and shot them both one after the other though my Chrony. I did find that topping up the gas was necessary between loading this gun as the gas chamber is very small. You will only get three shots out of a fill but the last shot is really slow.
I did find that I consistently got right around 250 fps on the fist shot and pretty much bang on 200 fps for the follow-up shot. Not super fast but fast enough to hit a small paper target 30 feet away pretty much every shot. Shooting 6 rounds on my paper target from 30 feet back using a semi rested position I was able to get 5 out of 6 shots pretty well placed on my paper target. I am not sure what happened to the 6th shot but it seemed to hook really hard to the right, perhaps the Airsoft BB was deformed? My 6 shot grouping with the excepting of the one shot that went MIA ended up being about 5 inches, not bad for such a small little low fps pistol.
So in terms of usefulness what can you expect from the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol? Well you are for sure not going to be sniping anyone with it but it could for sure come in handy as a surprise back for your backup gun!
Action: Over-under double barrel single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 2 rounds.
Energy: .6 Joules.
Trigger Pull: The trigger pull on the ASG - Marushin Chrome Derringer is single action only so you will have to cock the hammer separately for each of the two shots. The action of the single action trigger is extremely short with virtually no take-up to speak of. The trigger pull is also very light.
Accuracy: This part of the review is yet to be determined as I have not done my Field Test or Shooting tests for this pistol. I will put a link in here when I have done my official Field Shooting Test. I have done a little bit of playing around with the ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol and can say it is not going to be the most accurate or powerful gun out there but that's not really what this ultra compact gun is meant for, more of a surprise, hey where did that come from kind of gun!
Build Quality: The ASG Chrome Derringer 6mm Gas Airsoft Pistol is built by Marushin and as a Japanese based company it is going to be mostly plastic but with that said this little pistol is built really well, the mechanical parts that need to be metal are, like the grips hammer, trigger, safety and many of the pins and screws. Everything is tight and the tolerances are excellent. The finish is also pretty much flawless.With the added metal parts this .5 pounds pistol actually feels pretty solid in the hand and it's hard to tell so much of it it is actually plastic.
Realism: The ASG - Marushin Chrome Derringer 6mm Gas Airsoft Pistol looks the part of a real steel Derringer in terms of size and mechanical parts all functioning as they would. Even the over-under barrels are recessed to look like a much larger caliber than 6mm. The only real give away would be the small gas valve located under the handle and of coursee the lighter weight.
Not a lot of meat parts but the metal grips, hammer, trigger and safety seem to add enough weight to make this Derringer feel pretty solid in the hand.
Nice recessed over-under barrels.
Mechanical part feel solid and tight.
Cons:
Main gun build is plastic, typical of Marushin guns.
Not a lot of power from my preliminary testing.
Only 2 shots so make them count!
Comments:
The ASG - Marushin Chrome Derringer is a rather unique 6mm Gas Airsoft Pistol and is not going to make a very good primary weapon or for that matter even a good secondary weapon, but on that off chance you want surprise on your side then this little guy would make a really great last resort gun for when you only have that one shot up close and personal and it's now or never... There's also the fact that it's a Derringer and how cool is that!
My Vimeo Table Top Video Review for this ASG Chrome Derringer 6mm Gas Airsoft Pistol:
In this Field Test Shooting video I test out the performance of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol using my Chronograph to get a real world (FPS) Feet Per Second rating. I also position myself 30 feet back and shoot 10 rounds at a paper target using a semi-rested shooting position (Sand bag up front and standing in the back).
In terms of velocity the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol shot a bit on the fast side at 414 FPS when averaging a 5 shot strong using .20 gram BB's with a brand new CO2. Keep in mind I was using the CO2 magazine which will have more power than the Gas Magazine version. I would assume the Gas mag version would shoot right around the mid 300's which may be more suited for indoor Airsoft games. For outside Airsoft wars you may want the extra power of the CO2 mag for shooting at targets further distances out.
Stepping back 30 feet and shooting at my paper target, the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol produced a decent 2 inch 10 shot grouping that was just a hair low but well centered left and right. The low factor could be adjusted up using some Hop-up tweaking. The trigger in single action mode is light and the release is crisp. Even the double action trigger is fairly light for double action, but there is a lot more take up since your finger is doing all the work that the blowback action would normally do for you when shooting in single action.
With the heavy blowback and high FPS the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol creates a really great shooting experience. It would be great for some target practice, getting some additional trigger time in if you are a Sig Sauer P226 owner and would make an excellent outdoor Airsfot war backup weapon. The quality is excellent and as a lover of the Sig Sauer lineup of guns I highly recommend this Airsoft pistol from KJWorks.
Trigger Pull: The trigger pull on the KJWorks KP01-E2 Sig Sauer P226 Airsoft Replica is good in both single and double action. Once the slide is pulled back and released the first round is chambered and the hammer will remain back placing the KJWorks P226 in single action mode, the pull is light and the take-up is nice and short, most of your shots will be in single action mode unless you use the de-cocker to lower the hammer for a subsequent double action follow-up shot, double action shots are still pretty light but much longer in order to cock the hammer back.
Accuracy: (I have not shot the KJWorks distributed CO2 Mag version but I have already done a Field Test Shootinng Review for the same KJWORKS gun distributed and licensed by Cybergun in the Gas Mag version. Here is what I had to say about the Cybergun Gas Magazine version: "Shooting the Cybergun Sig P226 from 20 feet out in semi rested position I was able to get very good results. I placed 10 rounds in about 1.5 inches with the shot placement being a bit low possibly due to my barrel mod, adjusting the hop-up may bring the aim point back up to where it should be. The Sig Sauer P226 Airsoft Replica shot right around the 316 fps range while conducting my 5 shot average chrony testing which was lower than advertised but I was using much heavier .20 gram BB's. You can expect to get a full magazine worth of shots out of each gas fill-up but I did notice that as the magazine got colder it did tend to become much less efficient and also seemed to vent a lot of vapor."
Build Quality: The build quality for all KJWorks guns in my opinion is one of the best in the business. Fit and finish is top notch with close tolerances in the working parts as you would find in a real steel gun. The paint is excellent and in general will wear much better than other Airsoft guns out there. The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is pretty much all metal and feels it, the recoil spring is nice and firm and all working parts are smooth and crisp when operated.
Realism: The KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol is a replica of the real steel Sig Sauer P226 with the exception of the licensing. The KJWorks KP01-E2 really is a great looking and functioning Airsoft Replica. You can field strip this gun exactly like a real Sig Sauer and all the mechanical parts work just the same including a working de-cocker and adjustable front sight. It is really hard to distinguish the Airsoft version from the real Sig P226 in both looks and feel.
All metal pistol with good overall realistic weight to it.
Very crisp and firm full blowback operation.
Some of the best fit and finish in the industry. Especially in price range.
Nice accurate looking and working Sig Sauer P226 Replica.
Working de-cocker.
White dot sights for quick target acquisition.
Front sight is adjustable for windage.
Full size drop out magazine holds Airsoft BB's and CO2.
Fully field strip-able.
Cons:
No actual Sig Sauer Licensing but very clean look.
CO2 Mag does stick out a bit and add to size
Comments:
I am a huge Sig Sauer fan so I have kind of high expectations with a replica gun! The KJWorks lineup as a whole is really fantastic, and what I say about the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol can be said about the entire lineup. KJWorks makes a super well built product that replicates the real steal version almost exactly other then they shoot Airsoft BB's instead of actual bullets. When holding a KJWorks gun in the hand you can feel the quality, in weight, ballence and especially when operating the slide, trigger and other working parts. Everything just feels so perfect and responsive. For the money you can not go wrong with the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol or any other KJWorks gun for that matter.
My Vimeo Table Top Review of the KJWorks KP01-E2 (Sig Sauer P226) CO2 Blowback Airsoft Pistol:
This First Person Shooting Clay Pigeons Video with my KJWorks M9A1 and 1911 Airsoft Pistol is to serve two purposes: Number one and really the only reason needed to make a video like this... To get outside on a nice warm summer day and practice some tactile shooting all while recording it in first person so you can come along and enjoy it with me :)
Secondly I wanted to inform everyone that the video uploads will be a bit lighter for the next week or so since I am on what I call a working holiday. I am focusing on a Fitness Contest this weekend along with a Fitness Expo the following weekend, nothing to do with Replica Airguns but it does coincide with my other Website and YouTube channelGetFitOver40.com. The Fitness contest is the Victoria Cup where I will be competing in the Men's Physique (Masters - Over 40) and (Open - All Ages) divisions. The Fitness Expo is called "theFitExpo" and it is in Anaheim California.
So if you want to watch more of my videos then you will have to checkout my other fitness channel for the next week where I will be posting lots of related content on what's going on fitness wise in my life right now.
Trigger Pull: The trigger pull on the KJWorks Beretta M9 & M9A1 is very good in both single and double action. Double action is a bit longer and heavier than when shooting in single action but not heavy by any means. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks M9 and M9A1 Airsoft pistols but I did get the chance to make a short preview video where I shot both guns at some clay pigeons setup around 20 feet away. I was able to pop the center out of the clay pigeons no problem and found that even without any practice I was consistently hitting dead center on most shots. I am not sure exactly what the FPS will be but considering both theses versions of the KJWorks M9 & M9A1 have the CO2 mags they should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slides cycle full length. Keep posted for my upcoming Field Test Shooting Video for both pistols.
Build Quality: As expected, the KJWorks M9 & M9A1 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to my my 4.5mm steel BB shooters. When using these guns regularly, areas that are painted like the metal friction areas show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWorks.
Realism: Both the KJWorks M9 & M9A1 are copies of the real steel popular Beretta M9 & M9A1, it is really hard to tell them apart from the real versions. Both the M9 and M9A1 are very similar in design with the M9A1 having some slight cosmetic differences, the biggest being the addition of a tactical rail built into the frame. Both KJWorks Beretta's can be field stripped in the same manor as a real Beretta M9 Semi Auto pistol and all parts function the same.
Pretty much all metal pistols with good weight to them.
Full heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seem to be very accuracy and well centered on target.
White dot sights make it easy to shoot an most backgrounds.
Ambidextrous safeties.
Field strip-able like the real steel versions.
Cons:
Sight are non-adjustable but elevation can be adjusted using the hop-up.
Grips may be a bit wide for some small handed people.
CO2 magazines sticks out a bit when using the CO2 mags.
Comments: The KJWorks Full Metal M9 & M9A1 are yet more examples of excellent full blowback Airsoft pistols from KJWorks. They are built to very high standards, are near perfect replicas of the real steel Beretta M9 & M9A1 and performance is also excellent. Yes the price is slightly higher than a similar Airsoft gun from KWC but the quality on the KJWorks is definitely worth the extra cost. Make sure to drop by our Replica Airguns Canada Store and checkout our new lower pricing on the KJWorks line of Airsoft guns.
My YouTube Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the KJWorks 1911 is very good since it is modeled after a real steel 1911 which makes it short and crisp with a very light trigger pull. There is a very slight take-up at the very beginning of the pull but once your get past this the release is crisp and perceptible. Since it is not a double action trigger you will need to either rack the slide for your first shot or pull the hammer back if you have already chambered a round.
Accuracy: I have not done my actual Field Test Shooting video review for the KJWorks 1911 Airsoft Pistol but I did get the chance to make a short preview video where I shot some clay pigeons setup around 20 feet away. The KJWorks Full Metal CO2 Airsoft 1911 was a lot of fun to shoot at the clay pigeons and I had no trouble hitting them form that range over and over again. I am not sure exactly what the FPS will be but considering this version of the KJWorks 1911 has the CO2 mag it should shoot up into the 360+ fps range using .20 gram Airsoft BB's. Blowback operation is strong and the slide cycles full length. Keep posted for my upcoming Field Test Shooting Video for the KJWorks Full Metal 1911 CO2 Airsoft Pistol.
Build Quality: As expected, the KJWorks 1911 build quality is just like all the other KJWorks Airsoft guns I've tested so far, excellent the fit and finish is the best in my opinion even when compared to any of my 4.5mm steel BB shooters or 6 mm Airsoft pistols. When using KJWorks guns regularly, areas that are painted like the metal friction areas and high spots show very light wear which is rarely the case with metal built blowback Airguns. Again the tolerances between the moving parts like the slide and frame are extremely tight showing excellent workmanship and machining from KJWorks.
Realism: The KJWorks CO2 Full Metal 1911 Blowback Airsoft Pistol copies the real steel very popular even today Colt 1911 A1, it is really hard to tell the KJWorks Airsoft 1911 apart from the real 45 caliber version. The KJWorks 1911 can be field stripped very similarly to a real 1911 Semi Auto pistol and all parts function virtually the same including a working safety, grip safety, slide catch-release, magazine release and hammer.
Pretty much all metal pistol with good realistic weight to it.
Full cycle heavy blowback operation.
Excellent fit and finish as always with KJWorks pistols.
High capacity 28 round full size drop out magazine that holds the Airsoft BB’s and CO2. (Can get Green Gas mags)
Seems to be accurate and well centered on target.
Nice two tone finish.
Working grip safety.
Nice light true single action only trigger.
Field strip-able.
Cons:
Sights are non-adjustable but you can adjust elevation using the hop-up.
Field strips a little different than a real 1911.
CO2 magazine sticks out a bit but KJWorks makes Gas Mags also.
Comments:
I am a big fan of 1911 pistols and love getting my hands on pretty much any version weather it be a Real Steel 45 caliber 1911, a 4.5mm Steel BB version or 6mm Airsoft Pistol. As long as it has that true 1911 single action short light trigger to it. I love the way the slide cycles a bit slower than most semi auto pistols and this can be found in many Airgun and Airsoft version like this KJWorks 1911 making the shooting experience even more realistic. The fit, Finish and overall quality of the KJWorks 1911 over other brands is worth the slight additional costs so if you don't mind paying juts a tad bit more for that extra quality and you're looking for a CO2 1911 then you will not be disappointed with the KJWorks Full Metal CO2 Airsoft 1911.
My Vimeo Table Top Review of the KJWorks M9and M9A1 Full Metal Blowback Airsoft Pistol:
We recently received some new pistols from KJWorks, The CO2 versions in Full Metal of the Colt 1911, the Berretta M9 and the Berretta M9A1. All of these guns are really well made, the fit and finish is excellent. Definitely a very high quality Airsoft pistol and worth spending a little bit more to get this extra quality. We have even lowered the price on many of our new KJWorks guns to make them even more affordable so check them out in our Canada Replica Airguns Store!
So I made a quick demo preview video where I get away from my table top and go outside to show them off a bit and shoot a few rounds through them at some clay pigeons. I did have some camera issues but you will get a good idea on how these guns look and perform.
My main goal in this Shooting Performance Test was to see how the ANT Advanced Novelty Tech CO2 HPAConversion Kit performed side by side with a standard 12 gram CO2. Keep in mind that you can also switch over at any time to a regular 12 gram CO2 even after installing the ANT adaptor system in the gun or magazine.
My choice of Airgun for this test was the KWC - Cybergun Mini UZIConverted to Full Auto. I chose this Blowback 4.5mm CO2 BB Gun because it uses a lot of CO2 with each shot and when shooting in full auto it literally eats CO2. I knew this airguns would really put the ANT Advanced Novelty Tech CO2 HPA Conversion Kit to the test.
My first performance test was to comparing both systems using a Chronograph so I could see how the fps velocity slowed down because of the CO2 cool down effect. The 12 gram CO2 did pretty well emptying a full 25 round magazine but keep in mind I was shooting in semi auto only for the sake of using a Chronograph. I did notice a drop in velocity from a high of over 300 fps to a low of around 260. When I switched over to the Bulk CO2 ANT System and performed the same test the fps started out a bit lower but stayed pretty much about the same with a few ups and downs. The initial lower fps may have been a result of using separate magazines for each test since the valves in each magazine are most likely tuned a bit differently to let out more or less CO2 with each shot.
My second and most impressive test was to empty a full 25 round magazine in full auto mode! Again a started out using the standard 12 gram CO2 and to make this a real world test, I did not replace the 12 gram CO2 form the previous test. I figured 50 shots was a realist amount of shots to get from a single 12 gram CO2 and after all I was only shooting in semi auto which uses a lot less CO2 then shooting in full auto.
My KWC Blowback Mini UZI rocked pretty good using the 12 gram CO2 until it hit about a third the way through the magazine and then it stated to slow down and pretty much stop dead in its tracks with about 5-6 rounds still left in the magazine. The CO2 was all gone and I was left a bit unsatisfied :(
Without any significant break time to let my KWC Mini UZI warm up again, I switched over to the ANT Advanced Novelty Tech CO2 HPA Conversion Kit magazine and unloaded the full magazine in no time with no cycle rate slow down at all, even after the magazine was deprived of Steel BB's I kept squeezing the trigger and letting the blowback hammer my shoulder for several more satisfying bursts. Now that is what you expect from a full auto Blowback BB Machine gun!
In conclusion, when shooting in semi auto you will see better fps consistency using the ANT Advanced Novelty Tech CO2 HPA Conversion Kit but where this system really shines at least for me is I can shoot as fast as as long as I want and it will feel same as the very first shoot I take even when using a full auto system. No more switching out 12 gram CO2 every few magazines, just speed load some more BB's in and your good to go.
I was sent a really cool new product form a company called ANT (Advanced Novelty Tech). Their CO2/HPA Converter allows you to hook up either a large CO2 tank or High Pressure Air system using standard Paintball hose system.
What's kind of neat with the Advanced Novelty Tech CO2 HPA Conversion Kit, is that you can still interchange your 12 gram CO2 if you want to even after modifying your gun to use Bulk CO2 or HPA!
The ANT Advanced Novelty Tech CO2 HPA Conversion Kit works with well over 100 BB, Pellet and Airsoft guns most of which would be Pistols but some rifles are included in this list.
The main advantages over using standard 12 gram CO2 cartridges would be a significant lower cost for CO2, along with less fps velocity fall off, so better performance overall.
Stay posted as I will be making a field test performance test using the ANT Advanced Novelty Tech CO2 HPA Conversion Kit with my KWC Mini UZI Full Auto BB Machine gun :)
The best way to describe a Blank Gun is to imagine it as a real gun in just about every way except one… There are no dangerous bullets flying out the front of it. That’s right, a Blank Gun just like a real gun uses a brass or metal shells, loaded with a primer and gun powder, but for what ever reason reason, some rocket scientists forgot to put a bullet at the end of the Blank shell.
Why Would You Want a Blank Gun?
Isn’t the entire purpose of a gun to shoot something? So why on earth would you buy a gun that doesn't shoot anything at all, what purpose would it serve? Even Nerf guns, water guns, potato guns all shoot something…
One way to look at a Blank Gun is to imagine it as a cap gun, but for grown ups. Similar to how kids like to shoot their cap guns because they go bang and sparks and smoke fly out of them, Blank Guns do the same thing but on a much grander scale and in most cases they look and sound a lot more like a real gun than a cap gun does.
So Blank Guns don’t actually do the main function of a real gun (that is to shoot a bullet), but they do look and sound the part of a gun. So how could this be of practical use to anyone?
Signalling Devices:
First off, have you ever heard of a Starter Pistol or a Flare Gun? Blank Guns have been historically used to signal the start of races. Many Blank Guns also have the ability to shoot flares by adding a flare adaptor to them so a person can shoot a flare into the air to signal distress if they are lost or hurt.
Gun Handling and Training:
Since many Blank Guns look, operate and feel almost exactly like real guns, Blank Guns are a great place to start out when training a person on proper gun handling and operation. If they make a mistake while using a Blank Gun, the consequences are far less severe than with a real gun. There is also much less kick from a Blank Gun so shooting a Blank Gun is less scary or intimidating for new shooters.
Dog Training:
Dogs used for police, military and hunting are required to stay calm around loud noises like gun shots, trained dogs also need to get used to the presence of guns and even how to attack the gun hand of a person who could be a potential threat. Again using Blank Guns in this training situation is a much better option than using a real gun for obvious reasons.
Movies, Video TV and Stage:
Introducing live ammunition on a movie set would be ridiculous, there is absolutely no need to shoot a bullet in this type of situation. Blank Guns make perfect stage props since they again look the part and sound the part without the dangerous bullets flying all over the place…
Collectors:
Many collectors want to own guns but for reasons like gun restrictions in their area, they may not be able to own a real gun or certain types of real guns. Blank Guns can offer a person with heavy gun restrictions in their area the ability to own similar Blank Gun versions. Perhaps they can own real guns but just simply don’t want to go through the licensing and registration hassle of owning a real gun. Blank Guns can generally be purchased for far less money than a real gun which is appealing to collectors who in many cases may not even shoot them.
Celebration:
In places like Turkey, people celebrate holidays and events by shooting Blank Guns into the air, at one time they actually shoot real guns, but people where getting injured or even killed by the falling bullets. Because of this, Blank Gun production became an industry in places like Turkey as Blank Gun manufacturers like EKOL, Retay and Zoraki (also know as ATAK Arms) are Turkish companies.
So now you know some of the reasons why a person would want to own a Blank Gun. I have Blank Guns and I also own real guns too. One reason is because there are many Blank Guns I own that I can not own in their real steel versions because of Canadian gun restrictions so obtaining a similar version in a Blank Gun allows me to own these models.
If a Blank Gun is not for you, then by all means get a real gun, but please understand that there is a place for Blank Guns, and in those environments, a Blank Gun is actually a better choice than a real gun.
