Today I decided to get outside since the weather was nice and make my Field Test Shooting Video for the ASG TAC-6 CO2 Airsoft Rifle (actually outside in the filed!) After all the ASG TAC-6 CO2 Airsoft Rifle is a sniper rifle and so I wanted to test it out at longer ranges than my 30 foot indoor shooting range can allow for. So I setup two paper targets at around 40 feet and 80 feet out, the actually distance may have been longer than that?
Starting off my Field Test Review I placed five .25 gram plastic Airsoft BB’s through my Chronograph and averaged 446 fps which is 6 fps faster than the claimed 440 fps from ASG. And that was with .25 gram Airsoft BB’s so if I was using lighter .20 gram BB’s I would expect velocity closer to around 500fps so don’t be shooting anyone with this Airsoft Rifle at close ranges!
Next I proceeded with my accuracy test placing 5 rounds on the target setup around 40 feet downrange. I managed to get all 5 rounds within about 2 inches of each other, not bad since this is a good 10 feet more than I usually test my Airsoft Rifles at. With the remaining 10 rounds in my magazines I was hoping to get at least a couple shots on my paper target setup a good 80 feet away but did not have much luck, I even reloaded the 15 round stick magazine 2 more times and gave it a go but again with no success! The Airsoft BB’s seemed to want to angle off in all direction usually up and to the right or left right before the 80 foot target, perhaps I would have had much better luck at 60 feet?
All I can surmise from this higher range Field Test is that the ASG TAC-6 CO2 Airsoft Rifle is not really a long range Airsoft gun at least with the .25 gram Airsoft BB’s I was using, maybe heavier Airsoft BB’s would settle down a bit more? I can say at ranges up to 40 feet the ASG TAC-6 CO2 Airsoft Rifle did perform just fine so keep that in mind when looking into buying one of these as smoking cans at 30-40 feet will be no problem and make for some fun times in the back yard or even basement makeshift gun range.
Type: Airsoft Rifle. Manufacturer: ASG. Model:TAC-6. Materials: Plastic with some internal metal parts. Weight: 3.5 pounds (1588 grams). Barrel: 12 inches, metal non-rifled. Length: 36 inches. Propulsion: 12 gram CO2 x 1. Action: Semi auto, double action only. Ammunition Type: 6mm BB's. Ammunition Capacity: 15 round metal stick magazine. FPS: 440.
Trigger Pull: The double action only type trigger pull on the ASG TAC-6 CO2 Airsoft Rifle is not too heavy but it is rather long so really quick rapped fire shooting will require some finger work. The trigger reset is right at the begging of the pull so you need to make sure you allow the trigger full range of motion or you may miss the odd shot.
Accuracy: I haven't done my Field Test Shooting video just yet for the ASG TAC-6 CO2 Airsoft Rifle but will shortly so stay posted for that video. ASG claimed the fps to be right around 440 and I am assuming with .20 gram Airsoft BB’s, I will most likely busing .25 gram Airsfto BB’s for my testing so I am hoping for around 400 fps or so. With the fiber optic front sight and fully adjustable rear peep sight I shoudl be able to get some decent rounds on target downrange and hopefully get a nice grouping.
Build Quality: The ASG TAC-6 CO2 Airsoft Rifle is mostly plastic but feels pretty good in the hand with decent fit and finish. There are some metal internal part along with the outer barrel and top rail but for the most part the ASG TAC-6 CO2 Airsoft Rifle is all plastic including the trigger and front and rear sights.
Realism: The ASG TAC-6 CO2 Airsoft Rifle is not a replica of any modern rifle that I know of but it does look a bit like a Beretta CX4 Storm especially the back half of it. The flash hider and top and bottom raise add to the realism. Available From: The Replica Airguns Store.
Pros:
Very customizable with rails top and bottom.
Comes with a rather nice Bipod that can be used with other rifles.
Front and back removable Iron sights are very usable, fiber optic in front, peep in back.
Safety switch is in a great location for right handed shooters.
Canada version comes with black flash hider.
Mostly plastic but solid construction.
Rubber Butt Pad is nice and thick.
Removable barrel to reduce size for easier transportation.
Also come in 4.5mm Steel BB version.
Optional Integrated laser can be added.
Cons:
DOA Trigger pull is a bit long which will slow down rapid fire shooting a bit.
Mostly Plastic Polymer build.
Why not a longer inner barrel for possible more fps?
CO2 is in the Pistol grip and not the magazine so may not be great for on field battles.
Comments: This may not be the most exciting Airsoft Rifle I have reviewed, it does look kind of cool and the price is right compared to other Airsoft Rifles. Who is it really for? I would say someone looking for an Air Rifle for plinking in the backyard or basement that perhaps want's a little bit more safety in terms of using plastic BB’s rather than Steel BB’s. Sure you can use the ASG TAC-6 CO2 Airsoft Rifle for Airsoft wars but most people want something a bit more realistic in terms of looks and function. Because the ASG TAC-6 CO2 Airsoft Rifle does have built-in Popup it shoudl be able to reach out to longer ranges so we will have to see if it can perform decent at longer ranges when I do my Field test Shooting Video.
My YouTube Table Top Review Video for the ASG TAC-6 CO2 Airsoft Rifle:
In this Field Test Shooting Video I put the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol through its paces to see how well it performs in the Replica Airguns Indoor Sea Can Airgun Shooting Range. I first place 5 rounds through the chronograph to see what the actual real world velocity is and then I shoot 10 rounds on my paper target 30 feet downrange to see how tight of a grouping I can get with it.
For my Chronograph Test I was using .25 gram Airsoft BB’s so the velocity will be a little bit under the claimed 370 using .20 gram Airsoft BB’s. The temperature was average, not hot or cold so right around room temperature. My 5 shot sting resulted in an average of 312 fps so I would guesstimate an additional 50-60 fps using the .20 gram BB’s since the Airsoft BB’s I was using where ab out 20% heavier than what was claimed. So 370 is for sure possible with the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol.
Going onto my accuracy test, again I used the same .25 gram Airsoft BB’s and placed 10 rounds back to back into my fresh paper target setup 30 feet away. As usually I had my hands resting on a sand bag up front and I was sitting in the back which helps get a fairly stable shooting position but not without some human factor involved. I did manage to place 4 rounds right inside the 1.5 inch bullseye but 6 did come out with my last shot being a bit of a flyer hitting rather low on the target. If I removed the flyer form the equation the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol did mange to shoot a 3 inch grouping. I do feel I can do better with this Airsoft pistol when I dial in the right Airsoft BB’s, hop-up and of course get a bit more use to shooting it.
All things considered, I really like the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol! It has one of the best triggers I have ever reviewed with a nice combination of short take up and light predictable trigger release. The blowback action is fast yet not overwhelming and the overall feel of shooting this gun is very satisfying. Make sure to also checkout my Table Top Video Review for the EMG TTI STI 2011 Combat Master John Wick GBB Airsoft Pistol where I go into more details about the specifications and features along with some nice close up video.
Type: GBB Airsoft Pistol. Manufacturer: Made by EMG. Model:TTI STI 2011 Combat Master. Materials: Aluminum & polymer components. Weight: 2.4 pounds (1100 grams). Barrel: 5 inches (127mm) metal non-rifled. Propulsion: Green gas. Action: Semi auto blowback, single action only trigger. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 28 round drop out full size metal magazine. FPS: Claimed 370.
Trigger Pull: The single action only trigger pull on the EMG TTI STI 2011 Combat Master is really great, there is virtually zero take-up with a light, crisp and easy release. You can double tap with ease making the EMG TTI STI 2011 Combat Master a great action pistol. One of the shortest and smoothest 1911 triggers I have tested, at least up there with the best for sure!
Accuracy: At this point I have not shot the EMG TTI STI 2011 Combat Master so I have no idea what the actual real world fps is going to be and how accurate it proves itself so my comments for this part of the review will ahed to wait till I perform my Field Test Shooting Video coming up shortly…
Build Quality: TheEMG TTI STI 2011 Combat Master is for the most part an all metal gun with a CNC Machined Aluminum Slide and metal slide along with mostly ,metal parts throughout. The guide rod is stainless steel and the barrel is also aluminum with an anodized rose gold finish. The fit and finish is awesome on the EMG TTI STI 2011 Combat Master with attention to detail everywhere. The only plastic I could find on this Airsoft pistol would be the grips and the skeletonized trigger.
Realism: The EMG TTI STI 2011 Combat Master is based off of the STI 2011 but is really a replica of the John Wick pistol used in the John Wick 3 movie and is virtually the spitting image to it. You will find licensing and trademarks where you would find them on the real steel version. Of course all the mechanical parts work like the real version and the EMG TTI STI 2011 Combat Master can be fully field stripped.
Pros:
Super crisp, light and short SAO trigger.
Fit and finish is excellent, very little slide wiggle.
Extremely close replica of the custom STI 2011 pistol used in the John Wick 3 movie.
Rear sight is fully adjustable and is not too bulky.
Fiber optic front sight helps with quick targets acquisition.
CNC machined two tone Aluminum slide with metal frame.
Rose Gold barrel looks great!
Full size high capacity 28 round double stack metal magazine.
Ambidextrous thumb safeties.
Working grip safety as you would expect on a 1911 based gun.
Most Mechanical parts work just like a steel version and can be easily field stripped to access hop-up.
Super crisp and fast blowback action, great for action shooting.
Licensing all over this gun true to the real steel version..
Cons:
Comes with the red tip but can be remove pretty easily.
Need a tool to remove the two part guide rod and barrel (don’t lose the screw!).
No dot’s on the rear sight.
Comments:
The EMG TTI STI 2011 Combat Master has got to be one of the most gorgeous and sticking Airsoft Pistols I have reviewed so far. Just everything about this pistol looks and feel great. For a $299 Canadian Pistol you get a really well made high quality product that will be a collectors item to own for years to come. It’s not a small or light gun but for it’s size it feels really well balanced in the hand but for those with small hands it may be a bit too much of a handful. If you see them in stock on our website, make sure to grab one while you can!
In this Update Preview Unboxing Video I take a look at 5 products that came across my table and that I have not reviewed so far on the Replica Airguns YouTube channel.
First I show off an HPA tank from Air Venturi that works perfectly for the Sig Sauer MPX and MCX Pellet Rifles allowing for more consistent fps and I would image a higher overall fps? We will find out when I test it out in the replica Airguns Indoor Sea Can Airgun Range.
13 Oz Aluminum
10 Inches Long
2 Inches Diameter
Integrated Pressure Gauge
Includes Buttstock
CO2 Adaptor Included
3000 PSI Fill
1100 PSI Regulated
Next I take a look at the KJWorks M9A1 GBB Airsoft Pistol, I hover revived the CO2 version before but this version comes with the Gas magazine rather than the CO2 mag for those that prefer gas operated Blowback Airsoft Pistols. Because of the slightly lower FPS the Gas version comes with a barrel extension to make it Canada import friendly.
6mm Airsoft BB’s
Green Gas / Propane
370 fps
25 Round Magazine
2 Pounds
Probably one of the most interesting product I look at in this video at least for me is the EMG JW3 Combat Master GBB Airsoft Pistol. This Airsoft pistol is mainly aluminum with some polymer based off of the 2011 STI and was featured in the 2019 John Wick 3 Film. I’m really looking forward to testing this one out in the Sea Can Replica Airguns Airgun Range!
6mm Airsoft BB’s
Green Gas / Propane
9.4 Inches
366 fps
28 Round Magazine
2.4 Pounds
Moving along to another Air Pistol I finally get my hands on the Crosman P1 which is really just a KWC PT92 4.5mm Blowback CO2 BB Pistol but with Crosman Branding and an included laser. Since I have never shot a PT92 BB Pistol with a laser I will probably make a Field Test Shooting Video to see how well it performs.
4.5 mm Steel BB’s
CO2 x 1
4.2 Inch Barrel
330 fps
19 Round Magazine
2.4 Pounds
Comes with Laser Sight
Last up I take a look at the ASG TAC-6 which is pretty much the exact same ASG TAC-4.5 CO2 Air Rifle I tested a while back but in this case the 6 refers to it being a 6mm Airsoft Rifle rather than a 4.5mm Steel BB Riffle. I am not sure I will do a full Table Top Video since these guns are virtually identical but just in different Ammo types but I hope to get outside and see how well it performs shooting at a bit more distance than the 30 foot indoor range I usually test my Airgun in.
In this Field Test Shooting Video I perform my usual Chronograph and Accuracy tests in the Replica Airguns Indoor Sea Can Shooting Range to find out what the actual feet per second velocity is and how accurate the ICS CPX-APE SF1 AEG Airsoft Rifle is in both semi auto and full auto. Watch my Table Top Video if you are looking for more info on Specifications and Details along with a full tear down of the ICS CPX-APE SF1 AEG Airsoft Rifle.
First up I place 6 rounds through my Chronograph to see what the real world velocity is and the ICS CPX-APE SF1 AEG Airsoft Rifle was able to average 391 fps using .25 gram plastic Airsoft BB’s. ICS claims the ICS CPX-APE SF1 is capable of fps up to 460 fps but this would be using lighter .20 gram Airsoft BB’s which I believe is entirely possible!
Next I put a fresh paper target on my metal backstop 30 feet downrange and proceeded to shoot 10 round in semi auto to see how tight of a grouping I could get. I was happy to see that 7 of my 10 rounds all grouped nicely within the 1.5 inch bullseye and only 3 came out just slightly increasing the grouping to around 2 inches but still closer to 1.5 inches. When I switched over to full auto and emptied the 300 round magazine into the target, amazingly the grouping still seemed to stay pretty close to 2 inches in diameter with some stragglers. The ICS CPX-APE SF1 AEG Airsoft Rifle punched a satisfying hole in my target going through several layers of cardboard.
As you can see in this YouTube Field Test Shooting Video the ICS CPX-APE SF1 AEG Airsoft Rifle performed very well for me living up to its pristine price point. You will pay top dollar for the ICS CPX-APE SF1 AEG Airsoft Rifle but will also get top quality with a ton fo features including an almost all metal/aluminum build, ambidextrous controls throughout, tons of add on capabilities using the 5 sided Keymod hand-gurd, fully adjustable folding stock and exceptional performance.
Type: AEG EBB Airsoft. Manufacturer: ICS Model: CPX-APE SF1 Materials: Mostly Metal/Aluminum. Weight: 6.4 pounds (2900 grams). Length: 25.2 inches folded / 32.5-36.2 unfolded. Hop-up: Yes adjustable. Propulsion: AEG EBB (Electric Blowback). Action: Semi & Full Auto single action only electric trigger. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 300 rounds. FPS: 460 fps.
Trigger Pull: The trigger pull on the ICS CPX-APE SF1 AEG Airsoft Rifle is pretty much like most AEG Electric trigger operated Airsoft Rifles. Usually mid range, light and with no real noticeable release point since it is an electric on and on switch at the end of the day and not really mechanical. Of course you can elect between semi and full auto operation at will.
Accuracy: I have not done my actual Field Test Shooting video review for the ICS CPX-APE SF1 AEG Airsoft Rifle but plan to tackle this video next on my list so this week for sure, stay posted of this one as I have not Field Tested any ICS Airsoft Rifles to date and really don’t know what to expect!
Build Quality: The G&G ICS CPX-APE SF1 AEG Airsoft Rifle is extremely well made as the price tag would suggest. You are going to find metal almost everywhere on this product including the all aluminum upper receiver. The only plastic I could find on the ICS CPX-APE SF1 AEG Airsoft Rifle was in the magazine and the folding butt stock. Everything else is metal/aluminum including the upper and lowe receivers, the sights, the rails and all of the controls. Fit and finish feels great as-well!
Realism: The ICS CPX-APE SF1 AEG Airsoft Rifle is not a replica so to speak of any one particular gun in production but does have some AR and perhaps SCAR attributes to it. Perhaps there needs to be a real steel version of this gun as it does combine a bit of the best of a both platforms. The ICS CPX-APE SF1 AEG Airsoft Rifle is sold for sure with great weigth and feel to it being that it is mostly metal. All the controls work exactly like you would expect on a the real powder burner and you can totally take this Airsoft rifle apart in just a minute or two with virtually no tools.
Mostly metal construction with full aluminum upper receiver.
Tons of rail attachment options with the 5 sided Keymod rail hand-guard.
Fully adjustable pop-up iron sights.
Most everything is ambidextrous: Selector switch, Magazine release, Charging handle, Sling mount.
Rear folding stock has tons of positions, 6 in length and 5 for cheek rest.
Super easy access to everything, hop-up, gear box, inner barrel, outer barrel.
Electric blowback system for slight recoil effect.
T-window in magazine for quick ammunition checks.
FPS is nice and high, great for longer range shooting.
Cons:
On the expensive side but very high quality.
Limited battery options as space for a battery is tight.
May have a bit too high of fps for closer quarter indoor Airsoft games.
Comments:
The ICS CPX-APE SF1 AEG Airsoft Rifle is not an inexpensive product and may be a bit out of touch for Airsofters on a tighter budget. That said it is really well thought out and well built Airsoft product that is ready to go with no real upgrading required. You may want to show on an optical or red dot sigh, perhaps a tac light or fore grip? Nothing you need right away. There really isn’t one thing I can point out that makes this gun so great, it is a combination of everything. when it comes down to it the ICS CPX-APE SF1 AEG Airsoft Rifle kind of has it all going for it. I am looking forward to seeing just how well it performs during my Indoor Field Test. I have high hopes!
It was a decent day today, not too cold and not raining at least at the time I and ethics video :) I figured with my new Insta60 One R and iVUE Vista cameras it would be a great day to test them out outside shooting with my G&G SMC-9 Full Auto Airsoft Carbine. I like the bak for more regulated Indoor Field Tests, these outside usually clay pigeon shooting videos are a lot more fun and I think a nice break for everyone.
So in this video I have three cameras rolling and switch camera switch back and forth throughout the video to make the experience more immersive. I have cameras setup front and back (Sony RX100 IV in front & Sony HDR-AS15 Back), along with my iVUE camera glasses and my Insta360 One R mounted to the barrel of my G&G SMC-9. All in all I think the video turned out well. It may be time to upgrade my Sony Action Camera as it is probably the oldest camera in my collection and you can see in the video it does not look as good as the other cameras.
I wanted to compare the KWC/Cybergun PT 24/7 G1/G2 BB and Airsoft Pistols to each other in the Replica Airguns Indoor Airgun Shooting Range to see how they compare side by side not only in terms of accuracy but also what their Feet Per Second Velocity performance would be.
Like all my Field Test Shooting Videos I place 5 rounds through my Chronograph and average out the fps to see what their real world velocity is using a brand new CO2 along with standard 4.5mm Steel BB’s and .25 gram 6mm Plastic Airsoft BB’s. I then place a paper target 30 feet down range and proceed to put 10 rounds from each gun into a fresh paper target to see not only how close the Airguns shoot to the bullseye out of the box but also how close each 10 round grouping is.
All of the KWC Cybergun Taurus PT 24/7 G1/G2 BB and Airsoft Pistols performed fairly well, the KWC PT 24/7 G1 NBB Steel BB Pistol as expected had the highest velocity at close to 400 fps while the KWC PT 24/7 G2 Blowback Airsoft Pistol with the slightly heavier then normal Airsoft Plastic BB’s shot closer to 300 fps. The KWC PT 24/7 G2 Blowback Steel BB Pistol shot just over 300 fps.
In terms of accuracy The KWC PT 24/7 G1 NBB Steel BB Pistol had one of the tighter grouping close to 2 inches but shot a fair amount to the left of the bullseye. The KWC PT 24/7 G2 Blowback Airsoft Pistol shot well centered left to right but low on the target with a spread of just over two inches and the KWC PT 24/7 G2 Blowback Steel BB Pistol was the most centered on target getting again close to a two inch grouping.
I do like the KWC Cybergun Taurus PT 24/7 G1/G2 BB and Airsoft series of Airguns and personally prefer the newer Blowback G2 models but to each their own.
When we have multi potions for a specificities model of Airgun I like to compare them to each other to understand the similarities and differences of each Airgun. Often time the differences are as simple as what ammo they use, if they have licensing or not, who they are distributed through, slightly model revision and of course some cosmetic differences.
In this YouTube Video Comparison I lock at the the KWC Cybergun Taurus PT 24/7 G1/G2 BB and Airsoft lineup and go over their similarities and differences so you can decide which one may be right for you.
At one point in time the KWC Cybergun Taurus PT 24/7 G1/G2 BB and Airsoft Pistols came in these version:
In this Field Test Shooting Video I test out the G&G SMC-9 GBB Airsoft Carbine in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see if the real world performance matches the manufacturers claims. I first place 5 rounds through my Chronograph using .25 gram Airsoft BB’s with a fully gassed up extended magazine to find out what the actual FPS is. I then shoot 10 rounds from a seated and rested shooting position into a fresh paper target setup 30 feet down range to see just what we can expect and then just for fun I shoot the 40 rounds left in the 50 round magazine in full auto to see how this also effects accuracy.
Starting with my Chronograph test, the G&G SMC-9 GBB Airsoft Carbine averaged 339 FPS with the fastest shot recorded at 350 fps and the slowest being 324 fps, so very consistent in terms of sustained fps during my Chronograph velocity testing. The velocity was a bit under the claimed 366-375 fps but I was using slightly heavier BB’s and it wasn’t super warm temperatures in the Sea Can on this testing day, around room temperature, (20 degrees Celsius or 68 degrees Fahrenheit).
Moving onto the accuracy testing for the G&G SMC-9 GBB Airsoft Carbine, it performed pretty decent shooting about a 10 round 4 inch grouping but if I removed two flyers top and bottom the grouping would have been loser to 1.5 inches. The grouping was well centered on the target but I did adjust the sights up a bit as initially out of the box the G&G SMC-9 GBB Airsoft Carbine was shooting fairly low at 30 feet out. The good news is the G&G SMC-9 GBB Airsoft Carbine has fully adjustable sights for windage and elevation along with the 120 clicks of hop-up adjustment. When it came to my full auto testing I found I was shooting really low, perhaps from the blowback recoil pushing me of target? This was the case at least when I did a 40 round mag dump. When I performed the test using shorter bursts I was able to keep more rounds centered on the target for sure but accuracy in full auto was not nearly as good as in semi auto because of the heavy blowback.
Over all the G&G SMC-9 GBB Airsoft Carbine performed decent for me, the velocity was bang on right around what is claimed by G&G allowing this GBB Airsoft Carbine to shoot targets at further out ranges. Accuracy in semi auto was also very good but again shooting in full auto will take a bit more of your attention keeping the blowback recoil under control, for this reason burst fire in full auto will give you better accuracy which is more than likely how you would be shooting the G&G SMC-9 GBB Airsoft Carbine anyways. I really like the diversity you get with the G&G SMC-9 GBB Airsoft Carbine and if you are into Gas Blowback Airsoft guns, then I feel you get similar performance to an AEG but with a lower capacity magazines, but then again I may just have to get my hands on a drum magazine for the G&G SMC-9 GBB Airsoft Carbine and see how that changes things.
Type: Gas Blowback Airsoft Carbine. Manufacturer: G&G Model: SMC-9 Materials: Metal/Aluminum & Polymer. Weight: 4.7 pounds (2125 grams). Length: 410/620mm folded/unfolded length Hop-up: Yes - 120 click adjustment. Propulsion: Green gas or propane. Action: Semi & Full AutoBlowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 50 rounds. FPS: 366-375 fps.
Trigger Pull: The trigger pull on the G&G SMC-9 GBB Airsoft Carbine is typical single action only with a soft short take-up and light release point. I would not call this a crips trigger since it does have a rather spongy feel to it but this is only noticeable when you are easing the trigger slowly. In reality you will be engaging the trigger quickly when shooting it on the field and won’t notice any of the creep or take-up. I would consider it to be a decent trigger pull over all.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G SMC-9 GBB Airsoft Carbine but as with most of my Full auto Airguns I find it hard not resist going outside and blasting off at least one magazine in full auto. Of course this was the case with the G&G SMC-9 GBB Airsoft Carbine and I can tell you I went through all 50 rounds in not time and the G&G SMC-9 GBB Airsoft Carbine rounds went exactly where I pointed the gun short and long range so I expect my Field Test Shooting video to produce good results.
Build Quality: The G&G SMC-9 GBB Airsoft Carbine feels amazing in the hand with a lot of metal going on in the upper Carbine conversion kit portion, the front rail assembly is CNC Aluminum and the Pop-up iron sights are actually metal. The rear fold out stock is plastic but it is sold and just like the rest of the G&G SMC-9 GBB Airsoft Carbine very well made with great fit and finish. Of course the lower polymer frame is from the G&G GTP9 and just like all of the G&G pistols is very well made.
Realism: The G&G SMC-9 GBB Airsoft Carbine genuinely feels like a real steel firearm when holding it in the hand. Shooting it feels much the same but obviously with a lot less recoil than a powder burner. Just like a real steel 9mm Carbine the G&G SMC-9 GBB Airsoft Carbine mechanically works virtually the same with working slide catch release, charging handles, magazine release, and duel safeties, all ambidextrous by the way. As expected you can fully field strip the G&G SMC-9 GBB Airsoft Carbine.
Lots of metal parts giving the G&G SMC-9 GBB Airsoft Carbine really good weigth and feel.
Fold out stock sits nice and tight using magnets when not in use.
Integrated QD sling swivel.
Comes with two different sized Back-straps to accommodate small and larger hands.
Super high capacity extended 50 round magazine that holds a ton of gas for consistent power and lots of shots per fill.
Converts the standard GTP9 semi auto pistol into a full auto Carbine.
Almost everything is ambidextrous.
CNC 20mm / MLOK Rail for lots of accessories options.
Actual metal pop-up fully adjustable sights.
Easy to adjust hop-up without disassembly.
Dual safety system, cross bolt on frame and trigger safety.
Cons:
Fold out stock is not adjustable which makes the sights are a bit tight.
Does not come with the pistol slide if you want to covert it back to the GTP9.
Comments:
I am a big fan of the full line of G&G Airsoft guns and so far their GBB pistol lineup has been a treat to review, adding their new G&G SMC-9 GBB Airsoft Carbine to the lineup for me is the perfect mix between their GBB Pistol lineup and their mostly AEG Rifle lineup. I am hoping to see if I can acquire the drum magazine and eventually see how that works with the G&G SMC-9 GBB Airsoft Carbine, for now the 50 round extended magazine will have to do. Really looking forward to testing out the G&G SMC-9 GBB Airsoft Carbine so stay posted for those results shortly!
My YouTube Table Top Review of the G&G SMC-9 GBB Airsoft Carbine:
I often have people ask me what is more powerful in terms of one gun over another and which Airguns have more raw power, BB versus, Pellet, versus Airsoft, versus Paintball?
Well in this indoor field test shooting video I compare all of the above head to head to see which Airgun not only has the most raw power but also how well they perform on a target setup 30 feet down range since after all what does it matter how powerful a gun is if it can not hit the target!
The Airguns I used in this head to head shooting performance test where as follows:
Keep in mind the ammunition for each Airgun is very different not just in terms of materials but also their weight which will have a big effect on the energy they produce. For example for this test I used 4.6 grain 4.5mm Steel BBs, 4.6 grain 6mm Aluminum Airsoft BB’s. 6.9 grain .177 cal. Lead Pellets and 17.7 grain .50 cal. Rubber Paintballs.
Watch my YouTube Video to see how well each Airgun did in this comparison shooting test!
In this Field Test Shooting Video I test out the G&G Piranha MK I & TR GBB Airsoft Pistols in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see what the real world performance is for these very similar Airsoft Pistols. I first place 5 rounds through my Chronograph for each Airsoft Gun using .25 gram Airsoft BB’s with fully gassed up magazines to find out what the actual fps velocity is. I then shoot 10 rounds from a seated and rested shooting position into fresh paper targets setup 30 feet down range to see just what we can expect in terms of accuracy from the G&G Piranha series.
Starting with my Chronograph test, a placed 5 rounds through my Chronograph with both the G&G Piranha MK I and G&G Piranha TR GBB Airsoft Pistols. Technically they should have performed nearly identical but not all guns are setup exactly the same out of the box and so the G&G Piranha MK I GBB Airsoft Pistol did shoot a bit hotter than the G&G Piranha & TR GBB Airsoft Pistol averaging 290 fps versus 257 fps. As a quick test I placed the magazine from the MK I into the TR and the G&G Piranha TR GBB Airsoft Pistol did shoot much hotter and very close to the G&G Piranha MK resultsI. I would assume the valves in these magazines where perhaps not letting out the same amount of Gas hence the difference in velocity. The velocity was well under the claimed 370+but I was using slightly heavier BB’s and it was a little cold in the Sea Can on this testing day, not quite room temperature. Around 19 degrees Celsius or 66 degrees Fahrenheit.
Moving onto the accuracy testing for the G&G Piranha MK I & TR GBB Airsoft Pistols, they performed pretty well shooting 10 round 2 inch groupings with both Airsoft Pistols shooting on the money vertically while the G&G Piranha MK I shot a bit to the left and the G&G Piranha TR shooting well centered all around.
All in both of the G&G Piranha MK I & TR GBB Airsoft Pistols performed good for me, I would have liked to have seen the fps higher since both guns where well under the claimed 370+ fps but for close quarter shooting you should have no problem with either of them and again maybe your magazine will shoot a bit hotter than mine did. The partial blowback action is snappy and quick with just enough recoil action to give that realistic shooting experience. The triggers on the G&G Piranha MK I & TR GBB Airsoft Pistols are really nice allowing for quick tight followup shots and again if you like the look and feel of a Glock but perhaps want something a bit more unique then you will want to consider one of the G&G Piranha series Airsoft Pistols know doubt.
In this Field Test Shooting Video I test out the G&G GPM92 GP2 GBB Airsoft Pistol in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see what the real world performance is for this Beretta 92 styled G&G Airsoft Pistol. I first place 5 rounds through my Chronograph using .25 gram Airsoft BB’s with a fully gassed up magazine to find out what the actual FPS is. I then shoot 10 rounds from a seated and rested shooting position into a fresh paper target setup 30 feet down range to see just what we can expect in terms of accuracy from the G&G GPM92 GP2 GBB Airsoft Pistol.
Starting with my Chronograph test, the G&G GPM92 GP2 GBB Airsoft Pistol averaged 275 FPS with the fastest shot recorded at 278 FPS and the slowest being 274 FPS, so very consistent in terms of sustained FPS doing my testing. The velocity was well under the claimed 366 but I was using slightly heavier BB’s and it was a little cold in the Sea Can on this testing day, not quite room temperature. Around 19 degrees Celsius or 66 degrees Fahrenheit.
Moving onto the accuracy testing for the G&G GPM92 GP2 GBB Airsoft Pistol, it performed pretty decent shooting about a 10 round 1.5 inch grouping if I removed one flyer that pulled a bit to the left. The grouping was a little bit low but well centered left and right so even though the sights are none adjustable I should be able to pull up the shot placement a bit using the hop-up adjustment.
All in all the G&G GPM92 GP2 GBB Airsoft Pistol performed well for me, I would have liked to see the FPS just a bit higher but for close quarter shooting you should have no problem with it. The blowback action is nice and firm and the typical Beretta single and double action trigger is true to form allowing for a round in the pipe with the hammer safely decocted but ready to go with a quick release of the safety and a double action pull of the first round. The G&G GPM92 GP2 GBB Airsoft Pistol may be a bit bulky and heavy for some smaller handed shooter so keep that in mind.
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: Piranha TR Materials: Metal & Polymer. Weight: 1.5 pounds (670 grams). Length: 7.8 inches total Barrel: 4.01 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 370+ fps.
Trigger Pull: The trigger pull on the G&G Piranha TR GBB Airsoft Pistol is typical single action only with a easy short take up (some of which is the trigger safety engaging), followed by a crisp predictable light release. The quick slide cycle allows for quick semi auto shooting with the G&G Piranha TR GBB Airsoft Pistol making it a great fast action shooter with quick target acquisition between shots.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G Piranha TR GBB Airsoft Pistol but I expect it to perform similar to most G&G Blowback Gas Operated Airsoft Pistols and shoot consistently in the mid 300 fps with a 10 round grouping around 1-2 inches. Stay posted for my Field Test Shooting Video where I hope to confirm these predictions in the Sea Can indoor Airgun Shooting Range.
Build Quality: Like most off theG&G Airsoft guns, the G&G Piranha TR GBB Airsoft Pistol build quality is really nice. Fit and finish are excellent with virtually zero slide wiggle, you can also get the G&G Piranha TR GBB Airsoft Pistol in a two tone stainless slide and chrome finish barrel that looks really sharp. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust using a special tool without taking the Airsoft gun apart.
Realism: The G&G Piranha TR GBB Airsoft Pistol as far as I can determines not an exact replica of any specific real steel gun in production but it does share looks, size and feel to that of the Glock but perhaps with an even more modernized look to it. You will find realistic function to the G&G Piranha MK I GBB Airsoft Pistoling terms of it’s operation with its full blowback action, working slide catch release, magazine release trigger safety and takedown lever allowing for it to be easily and quickly field stripped.
Good balance of metal and plastic for a balanced and light feel.
Partial slide Blowback operation should allow for even better gas performance and snappy operation.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice two tone slide.
Has a working trigger safety.
Smaller spit grip perfect for people smaller hands.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
Dual 20mm top and bottom Rails for accessories.
Comes in all black and two tone black and sliver.
Comes with high quality speed loader
Threaded barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Not an actual replica of any specific gun I know of but does share some Glock attributes.
No actual frame safety other than the trigger safeties, (not always a bad thing).
Comments:
Overall I really like the new G&G Piranha TR GBB Airsoft Pistol, it has a really modern look to it yet has a familiar feel. The G&G Piranha TR GBB Airsoft Pistol is fairly light weight with that quick and snappy partial slide allowing for very quick follow up shots. Combine all of that with the new Gas saving Ceramic Whirl Cylinder Valve I expect the G&G Piranha TR GBB Airsoft Pistol to perform really well when in action. I like that you have the option of the more subdued all black version or if you like your guns to be a little bit more flashy you can also get it in the two tone with black and stainless version. The TR version over MK 1 does allow for optics on top which personally would not be my choice for this gun but it’s nice that you have this option.
My Table Top Review Video of the G&G Piranha TR GBB Airsoft Pistol:
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: Piranha MK I Materials: Metal & Polymer. Weight: 1.5 pounds (670 grams). Length: 7.8 inches total Barrel: 4.01 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 370+ fps.
Trigger Pull: The trigger pull on the G&G Piranha MK I GBB Airsoft Pistol is typical single action only with a easy short take up (some of which is the trigger safety engaging), followed by a crisp predictable light release. The quick slide cycle allows for some pretty quick semi auto shooting with the G&G Piranha MK I GBB Airsoft Pistol making it a great fast action shooter.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G Piranha MK I GBB Airsoft Pistol but I expect it to perform similar to most G&G Blowback Gas Operated Airsoft Pistols and shoot consistently in the mid 300 fps with a 10 round grouping around 1-2 inches. Stay posted for my Field Test Shooting Video where I will confirm these predictions.
Build Quality: Like pretty much all G&G Airsoft guns, the G&G Piranha MK I GBB Airsoft Pistol build quality is really good. Fit and finish are excellent with virtually zero slide wiggle, the two tone stainless slide and chrome finish barrel look really good. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust without taking the Airsoft gun apart.
Realism: The G&G Piranha MK I GBB Airsoft Pistol as far as I can determines not an exact replica of any specific real steel gun in production but it does share looks, size and feel to that of the Glock but perhaps with an even more modernized look to it. You will find realistic function to the G&G Piranha MK I GBB Airsoft Pistoling terms of it’s operation with its full blowback action, working slide catch release, magazine release trigger safety and takedown lever allowing for it to be field stripped.
Good balance of metal and plastic for a balanced and light feel.
Partial slide Blowback operation should allow for even better gas performance and snappy operation.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice two tone slide.
Has a working trigger safety.
Smaller spit grip perfect for people smaller hands.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
20mm Rail for accessories.
Comes in all black and two tone black and sliver.
Comes with high quality speed loader
Threaded barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Not an actual replica of any specific gun I know of but does share some Glock attributes.
No actual frame safety other than the trigger safeties, (not always a bad thing).
Comments:
Overall I really like the new G&G Piranha MK I GBB Airsoft Pistol, it has a really modern look to it yet has a familiar feel. The G&G Piranha MK I GBB Airsoft Pistol is fairly light weight with a quick and snappy slide allowing for very quick follow up shots. Combine all of that with the new Gas saving Ceramic Whirl Cylinder Valve I expect the G&G Piranha MK I GBB Airsoft Pistol to perform really well when in action. I like that you have the option of the more subdued all black version or if you like your guns to be a little bit more flashy you can also get it in the two tone with black and stainless version.
My Table Top Review Video of the G&G Piranha MK I GBB Airsoft Pistol:
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: GPM92 GP2 Materials: Metal slide & frame, real wood grips. Weight: 2.3 pounds (1040 grams). Length: 8.9 inches total Barrel: 4.6 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single and double action. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 28rounds. FPS: 366+ fps.
Trigger Pull: The trigger pull on the G&G GPM92 GP2 GBB Airsoft Pistol is very good in both single and double action. Double action is a bit longer but not that much heavier when shooting in single action. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM92 GP2 GBB Airsoft Pistol but it should perform similar to my earlier review of the G&G GPM92 GBB Airsoft Pistol where it performed fairly well shooting in the mid 300 fps with a nice under 1 inch 10 round shot placement for 30 feet down range.
Build Quality: Like pretty much all G&G Airsoft guns, the G&G GPM92 GP2 GBB Airsoft Pistol build quality is right inline. Fit and finish where excellent and a lot of attention to detail was seen all over this Replica Airsoft Pistol. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust without taking the Airsoft gun apart.
Realism: The G&G GPM92 GP2 GBB Airsoft Pistol is an excellent replica of the real steel Beretta Mod. 92FS, the safety even acts as a working de-cocker. You'll also find 5, 10, and 15 numbered markings on the backside of the magazine that would normally indicate how many bullets are in the magazine, a nice touch for sure! Everything works pretty much the same as it would on a real Beretta M9 including the ability to fully field strip the G&G GPM92 GP2 GBB Airsoft Pistol. I like the addition of th real wood grips that are a bit thicker than the plastic ones but if you ahed decent sized hands this shoudl not be a problem for you.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice real wood grips.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
20mm Rail for accessories.
comes in three different color schemes. Black, Silver, Gold.
Comes with high quality speed loader
Safety also works as a de-cocker.
Threaded removable barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Wood grips make the grips a bit thicker than plastic grips.
Price does go up especially if yo want the silver or gold version.
Comments:
I would have to say the new G&G GPM92 GP2 is one of the nicest Beretta Model 92FS Airsoft Pistols you are going to find out there, even a step up over the previous GPM92 model. There is a ton of attention to detail for sure, You also get the hard shell case with included high quality speed loader and G&G's updated Ceramic Valve and Revolutionary Whirl Cylinder Valve that help with freeze-up issues. It’s also nice that you no longer are required to filed strip the G&G GPM92 GP2 GBB Airsoft Pistol in order to adjust hop-up and the real wood grips just really finish off this quality product from G&G.
My Table Top Review of the G&G GPM92 GP2 GBB Airsoft Pistol:
In this Preview Unboxing Video I take a look at five Gas Blowback Airsoft Pistols. Three of them are from G&G and two are from ICS. All offer full blowback operation and are green gas or propane powered with full size metal drop out magazines.
I am super excite to showcase three awesome rifles in this Update Preview Unboxing Video. Two of which are Airsoft and one is a Steel BB shooter, all of which are semi and full auto selectable. In this video I do a bit of an unboxing and preview of each Rifle not going into too much detail as I want to leave most of the information for my Table Top and Filed Test Videos. The main purpose of this video is to let everyone know we have these Rifles in our Canada Replica Airguns Store now for sale.
I may as well talk about them in the order they appear in my video so lets start with the ICS CXP APE AEG Airsoft Rifle. The ICS CXP APE AEG Airsoft Rifle is a mostly metal Electric Airsoft Rifle with realistic electronic blowback operation along with a CNC machined aluminum upper and lower receiver. It comes with a hi-cap 300 round magazine and a Ver 2 Full Metal ICS Split Type Gearbox. The ICS CXP APE AEG Airsoft Rifle weighs in at just under 3kg.
Next I showcase the G&G SMC9 GBB Airsoft Carbine, a unique product that converts the G&G GTP9 pistol into a a semi and full auto Carbine and includes a 50 round extended magazine, there is an even higher capacity drum magazine made for this product! You will find a fold out stock along with a CNC Machined MLOK Rail for additional mounting options.
Last but perhaps one that I have been the most eagerly anticipating is the Crosman AK1 CO2 Blowback BB Rifle a twin CO2 Blowback 4.5mm Semi and Full auto AK style BB Rifle, finally a decent AK BB Rifle! The Crosman AK1 CO2 Blowback BB Rifle has a claimed fps of 430 and shoots 1400 rounds per minute in full auto, very similar to the Crosman DPMS series of AR styled CO2 Blowback Full Auto BB Rifles. The Crosman AK1 CO2 Blowback BB Rifle comes with a 25 round magazine and swing out rear adjustable stock.
