Trigger Pull: The single action only trigger pull on the Umarex DX-17 Spring Powered BB Pistol is actually pretty good. It's fairly short with only a little bit of very light take up and then an easy release that has no added friction. So you will have to get use to when and where the release happens but it is a really decent trigger for such an inexpensive airgun.
Accuracy: I have only shot the Umarex DX-17 Spring Powered BB Pistol a few times to get use to the mechanical operation of using this spring powered pistol since there is a very specific order in which you need to cock and load the Umarex DX-17 for proper operation. I did find the DX-17 shot a bit high for me at 30 feet out so I had to adjust my aim point about 5-6 inches lower to hit targets at this range. For further out shooting you many not need to do so since the fps is fairly low and I would expect the BB to drop pretty quickly. In terms of power being that the Umarex DX-17 Spring Powered BB Pistol is only rated at 200fps, well it seems sufficient enough for plinking away at targets and should have no problem getting through a pop can.
Build Quality: I was expecting this $20 low cost BB airgun to be fairly low quality in general but when I took it out of the plastic clamshell packaging I was pleasantly surprised by the overall quality and how the Umarex DX-17 Spring Powered BB Pistol felt in my hand. It has a good weight to it and the fit and finish are really good. Mechanical parts tolerances feel snug and the plastic used feels of good quality.
Realism: The Umarex DX-17 Spring Powered BB Pistol as far as I know is not a replica of any specific real steel gun in production but it does kind of remind me of a Browning Hi-power at least the back half and the way the frame angles up a bit in front of the trigger. Other than that it looks the part of a real gun. The DX-17 has what looks like real working parts on it with the slide catch, magazine release and magazine but plat all moulded into the airgun. Available at the:Replica Airguns Store
Pros:
At $21 Canadian its great value for a target plinker.
It actually looks and feels pretty good in person, better than I expected build quality and weight to it.
No CO2 required so very cheap to shoot.
Single action trigger is actually really decent, better than most airguns.
Accessory rail for adding a red dot or perhaps a tactical light.
15 round reservoir makes followup shots quicker and no fumbling around loading BB’s in-between shots.
Lower fps means if you do do something stupid you are less likely to have to make a trip to the doctor
Cons:
Pretty low fps so don’t expect any long range shooting or great penetration.
Sights are not adjustable and it seems to shoot kind of high.
Why not rifle the barrel and make pellets an option?
Comments:
I rarely review these super low cost airguns especially spring powered ones with low fps, it almost seems like why would you want any of that? But you know the Umarex DX-17 Spring Powered BB Pistol is actually a great little airgun and you really can't beat the price tag. You are also going to save a bunch of money not having to buy CO2 and once you load 15 rounds into the BB reservoir you can empty the DX-17 fairly quickly. Sure the power seems a bit low but it gets the job done and like I said if there was an accident, you are less likely to break that window or require medical attention. I think this would be a great add on to an existing order you might be making with us, that way you wouldn't have to pay for shipping for this one item and you get a fun little plinker for only $20 more.
My Vimeo Videos for the Umarex DX-17 Spring Powered BB Pistol:
Trigger Pull: The trigger pull on the Umarex Beretta APX CO2 Blowback BB Pistol is a little different then that of the real steel APX. On the real steel APX there is actually a trigger safety and the actual gun uses a striker based system with a fairly short reset and take-up. On the replica Airgun version the trigger does not have a built in safety and the reset and take-up are much longer (full length). I have read that both the real steal and BB versions of the APX both have about 6 pounds trigger pulls but I personally felt like the Airgun version was heavier than that, perhaps because of the long pull. Overall the Umarex Beretta APX CO2 Blowback BB Pistol trigger is acceptable but not my favorite.
Accuracy: I have not shot the Umarex Beretta APX CO2 Blowback BB Pistol so far but based on similar blowback stick magazine BB air pistols from Umarex with around 400 fps performance, I know that it will have a medium blowback feel and should shoot pretty close to the claimed 395 fps. I also expect at least a 2 inch or smaller 10 shot grouping from 30 feet back.
Build Quality: Very good, the Umarex Beretta APX CO2 Blowback BB Pistol feels heavier than 1.5 pounds in the hand, perhaps because it is a more compact gun. The metal slide, metal stick mag and internal metal parts all help to balance off the polymer frame nicely. Fit and finish is also good.
Realism: The Umarex Beretta APX CO2 Blowback BB Pistol overall is a really close replica to the real steel APX other than the added safety and missing trigger safety. The added safety does not stand out too much and does serve a purpose while the missing trigger safety could of at least been there for show if not an actual working safety. Other than that the Umarex Beretta APX CO2 Blowback BB Pistol is very close to the Beretta APX with its full licensing, open ejection port, recessed barrel working slide catch release and blowback operation. Available at the:Replica Airguns Store
Pros:
Great weight and feel to it, build quality seems really good.
Really nice replica of the original Beretta APX in most ways.
Working slide catch and release.
Fully Beretta licensed.
Easy to see white dot sights front and back.
Recessed barrel and open ejection port for added realism.
Accessory rail for adding a laser or tactical light.
Stick magazine but plate gives the elusion of a full size magazine and covers the CO2 tab.
Warning instruction are nice and discreet!
Cons:
Trigger is a bit long and perhaps heavier than the real steel APX trigger. It also does not have the trigger safety.
Has a stick magazine rather than a full size magazine.
Sights are non-adjustable which is common with airguns like this one.
Comments:
It's always nice to get another airgun replica for fans of that particular real steel gun so they have a low cost shooting option they can use in a lot more locations for some safe trigger time. The Umarex Beretta APX CO2 Blowback BB Pistol is a great addition for sure and it's also nice that it is somewhat Glock like in looks and operation for those Glock fans out there that are having a tuff time locating a Glock airgun replica :) Other than my trigger beef, I really like the Umarex Beretta APX CO2 Blowback BB Pistol. I hope it performs as good as it looks when I do my field test shooting video in a bit.
My Vimeo Videos for the Umarex Beretta APX CO2 Blowback BB Pistol:
Type: Air Rifle / Machine Gun. Distributer: Umarex Model: Legends MP 40. Materials: Mostly Metal build. Weight: 7.7 pounds (3.5 kilograms) Barrel: 10 inches - smooth bore steel. Propulsion: 2x12 gram CO2. Action: Internal BoltBlowback single action. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 52 round full size drop out magazine. Max FPS: 465.
Trigger Pull: The trigger pull on the Umarex Legends MP 40 Blowback CO2 BB Machine Gun is single action only and even though I have seen it tested at around 10 pounds pull, in person it does not feel that heavy and is actually fairly smooth. You will need ti charge the bolt for the first shot just like you would on the real steel MP 40.
Accuracy: I have not done my official Field Test Shooting Video for the Umarex Legends MP 40 Blowback CO2 BB Machine Gun but did take it outside for a quick test run. Like others have reported back you really need to take your time loading the double stack magazine properly or you can have some feeding issues. it may even be a good idea to use a little lubricant in the magazine to help with BB smoothness. I will know more after I ahed played around with the Umarex Legends MP 40 Blowback CO2 BB Machine Gun a little more and worked out the BB feeding issues.
Build Quality: The Umarex Legends MP 40 Blowback CO2 BB Machine Gun is pretty much all metal other than the stock and pistol grip. Pretty much everything that is black is going to be metal on this airgun. It weighs in at a hefty 7.7 pounds which is only a punt off form the real steel version. Overall the fit and finish is really good, all mechanical parts including the retractible stock work flawless.
Realism: The Umarex Legends MP 40 Blowback CO2 BB Machine Gun is a 1 to 1 replica of the real steel German made World War II Machine Gun. It is very authentic looking and has very similar operation. The BB version does have the ability to shoot in semi auto mode which the real steel version did not but this is a good feature for saving on CO2 and BB's It would have been nice if the bolt was abel to lock all the way back and up but since the movement is shortened this is not possible. Still the Umarex Legends MP 40 Blowback CO2 BB Machine Gun is a really nice replica and almost every way.
Great to have another full size Rifle / Machine Gun available to purchase in a BB gun version.
Mostly all metal design with good overall weight.
Semi and Full auto select-ability.
Dual CO2 design for increased shots and less cool down effect.
High capacity full size drop out metal magazine.
Great looking replica of the real steel MP 40 in looks, operation and weight.
Internal bolt blowback will give a bit of recoil feedback feel.
Adjustable rear sight for shooting at different ranges.
Price point is reasonable for this type of full size mostly metal rifle.
Cons:
Sights are not adjustable for windage.
Bolt does not go all the way back to the lockout position.
Some reviewers have said that a full mag load does not always work well in full auto mode.
Comments: When I first got my hand on the Umarex Legends MP 40 Blowback CO2 BB Machine Gun at this years SHOT Show I immediately knew it was going to be a hit. The Umarex Legends MP has a lot going for it... High fps, semi and full auto, nostalgia of being a war replica and super great build quality and fit and finish. The questions is really who wouldn't want one? Especially being a replica BB rifle which has to be one of the more limited areas when it comes to airgun replicas. I look forward to shooting this offering from Umarex a little more and sharing my experiences with everyone.
My Vimeo Table Top Review of the Umarex Legends MP 40 Blowback CO2 BB Machine Gun:
What's not to love about the Umarex Legends MP 40 CO2 Blowback 4.5mm Steel BB Full Auto Machine Gun? It's pretty much all metal weighing in at close to 8 pounds, The Legends MP has a max fps of up to 465, shoots in both semi and full auto and has a high capacity all metal 52 round magazine that holds not only 1 CO2 but 2 CO2 for close to 200 rounds of semi auto shooting or about 140 shots in full auto. I really look forward to my Field Test Shooting Review of the Umarex Legends MP 40!
Not to be out shadowed or forgotten in the preview video, I also show off another 2017 SHOT Show CO2 Blowback Air Pistol, the Umarex Beretta APX! Right away the Umarex Beretta APX feels nice and solid in the hand weighing in at around 1.5 pounds with a heavy metal slide and really high quality plastic or polymer frame. You will find some nice details like a cut out ejection port and recessed barrel and of course full Beretta licensing from Umarex. The Umarex Beretta APX CO2 Blowback BB Pistol has a pretty decent claimed fps of close to 400 and a 20 round stick magazine that when inserted has that full size magazine look to it.
You'll also find other nice details like white dot sights front and back and a working slide catch release. My only gripe with the Beretta APX is the trigger, it does not ahed the trigger safety you would find on the real steel Beretta APX and the action is very long and perhaps a bit heavy. Other than that the Umarex Beretta APX looks to be a really nice replica airgun.
I had a chance to take out my Swiss Arms SA 92 Stainless Version and Swiss Arms SA 1911 Tactical Rail System CO2 Blowback BB Pistols and see how they performed in the Sea Can Airgun Shooting range and they did pretty good, I have treated very similar KWC version of these guns in previous videos and for the most part the Swiss Arms Stainless Versions are just a little prettier cosmetically. I didn't test out the Swiss Arms SA 1911 Seventies Stainless Pistol since I expect it would have performed the same as the other 1911 in this Field Test Shooting Video.
So how did they do? First off I fired five rounds through my now almost perfectly working Chrony Chronograph and the SA 92 ended up shotgun a little faster with an average of right around 320 fps while the Swiss Arms SA 1911 Tactical shot an average of 302 fps. I was using brand new Sig Sauer CO2 and RWS Match Grade Precision Steel 4.5mm BB's for the entire review.
Moving on to the accuracy, I setup in my rested position which is about 30 feet back for the paper target. I was sitting and using a sand bag to rest the pistols on for stability. This gives me a very stable shooting position but there is still a little human factor involved since the guns are not locked in place. Both CO2 Blowback BB Pistols shot about a 2 inch 10 round grouping but the Swiss Arms SA 1911 had better shot placement pretty much hitting exactly where I aimed it, the Swiss Arms SA 92 Stainless on the other hand wanted to shot rather low, I had to place my aim at the top of the rings to get the SA 92 to hit near the bullseye. It did shoot really well left to right, unfortunately the Swiss Arms SA 92 Stainless does not seem to have a hop-up adjustment so you may have to adjust your aim point higher than normal with this one.
Both guns had great single action triggers with heavy blowback operation, I did find the Swiss Arms SA 1911 Stainless Tactical had a bit of a sticky slide when I first shot it but after a few shots it smoothed out. If you're looking for a KWA / Cybergun 1911 or Taurus PT 92 Blowback Airgun and want it ti have a little more curb appeal then make sure to checkout the Swiss Arms Stainless series of CO2 Blowback BB Pistols.
I know this video is going to excite many of you if you already like the basic KWC 1911 and PT92, also known as the Tanfoglio Witness, GSG 92 and many other almost exactly the same guns from Swiss Arms, Gletcher, Cybergun and even Umarex and Crosman.
There are tons of these KWC CO2 Blowback BB Pistols and Airsoft Pistols on the market in various versions with all kinds of different licensing on them and I have seen lots of custom modification photos from my viewers showing me how thy have striped and polished their KWC blowback Air Pistols and even added real wood grips.
That's why I think it's super cool that now you can get your already blinged out and polished Cybergun/KWC 1911 or PT92 and realy for not a lot more money at the end of the day! The real problems is availability since these stainless versions are in high demand.
So what are we looking at in this video? I have two Cybergun/KWC 1911's one is a basic 1911 A1 with a parkerized and stainless frame and slide, you also have a real wood look grip (Looks like wood but is not actually wood...) The basic Swiss Arms 1911 has been called the SA 1911 Seventies Stainless Pistol while the more tactical Swiss Arms SA 1911 is rightfully called the SA 1911 Tactical Rail System since it has a lot more tactical features like a rail, ambidextrous safety, white dot sights, and tactical trigger and hammer.
The Swiss Arms SA 92 Stainless which is essentially very similar to the GSG 92 or KWC PT92 again offers a parkerized and stainless frame and slide with the simulated wood grips.
Make sure to watch my update video for these three very attractive Swiss Arms CO2 Blowback BB Pistols from Cybergun/KWC and if you're interested in purchasing one you like then see if we have them in stock in our Canada Replica Airguns Store.
Type: Air Pistol. Manufacturer: Sig Sauer ASP Model:Sig Sauer ASP P320. Materials: Metal and plastic build. Weight: 1.81 pounds (821 Grams). Barrel: 4.75 inches - Rifled steel. Propulsion: 12 gram CO2. Action: Blowback single and double action. Ammunition Type: .177 caliber pellets and 4.5mm Steel BB's. Ammunition Capacity: 30 round belt fed stick magazine. Max FPS: 430.
Trigger Pull: The trigger pull on the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a lot better than I thought it was going to be considering each time you pull the trigger it has to advance the 30 round belt fed magazine and cock the internal hammer since it is double action only. The blowback operation is really only for show and feel since it does not cock the hammer for a more single action type trigger pull. You can expect a fairly long trigger pull because it is double action only but overall it is not too heavy.
Accuracy: I have not done my official Field Test Shooting Video for the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol but hope to have it done shortly. Since I also haven't really done an official shooting test for the Sig Sauer P350 and P226, I figure I will test out all three of them at the same time.
Build Quality: The Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a bit heavier (closer to 2 pounds) than the P250 which hits the scale at only 1.5 pounds , this does make the Sig Sauer P320 feel a bit more solid in the hand. The Sig Sauer P320 has a metal slide and polymer frames similar to the real steel version which gives it authentic weight, balance and handling. Sig claims that their entire APS line of pellet guns is life tested for 15,000 shots so you know this gun is going to last and provide years of shooting fun. The fit and finish seem really good, so far no real paint or finish problems and all mechanically everything is operating as it should.
Realism: The Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol is a very close replica of the real steel Sig Sauer P320. The hammer, slide catch release and take down leaver are purely for show with the hammer being moulded into the slide and frame. One slight disappointment for me is when a gun does not have a cut out ejection port, that is also the case with the otters ASP Sig Sauer airguns like the P226 and P250 but it does not take away from the shooting fun in any way.
Good overall replica of the real steel Sig Sauer P320.
Designed by Sig Sauer and made in Japan, fully Sig Sauer licensed.
Should have nice heavy blowback operation like the ASP P250 and P226.
Has better weight than the P250, almost half a pound heavier.
White dot sights for easy target acquisition and accessory rail for add ons.
Super high capacity 30 round belt feed magazine.
Decent feel to the trigger not heavy or as sticky as I thought it might be having a 30 round belt fed magazine.
Cons:
Hammer is moulded into the slide and frame, does not function at all.
Sight are non adjustable.
Ejection port is not cut out and there is no working slide catch.
Comments: I was happy when Sig Sauer released their ASP Sig P250 and P226 CO2 Blowback Pellet Pistols with their 16 round double sided stick magazines like we have seen in several otters CO2 Pellet Pistols. But I love the introduction of the 30 round belt fed magazine. I am hoping the belt fed magazine performs while actually shooting pellets as good as it feels when dry firing it, I guess we will have to wait and see when I do my Field Test Shooting Video :) Overall the new Sig Sauer ASP P320 Pellet Pistol looks to be an upgrade of sure to the P250 in terms of improved weight and a higher capacity magazine.
My Vimeo Table Top Review of the Sig Sauer ASP P320 CO2 Blowback .177 Caliber Pellet Pistol:
Another 4.5mm Steel BB Field Test Shooting Review from the new Sea Can Airgun Shipping Container Shooting Range. Yes it's a Crosman but it's really made by KWC and is based on the KWC Beretta / Taurus M92. Depending on which version you get, it came in either semi auto only or semi auto and full auto selectable. The Crosman version does shoot right out of the box in both semi and full auto which is nice.
On to my performance results with the Crosman PFAM98 Taurus PT-92 CO2 Blowback BB Pistol. My feet per second velocity results using a brand new CO2 in a 22-23 celcius environment where right up around 333 fps from a 5 shot string. This is about what we are use to from KWC full blowback CO2 BB Pistols.
Moving on to accuracy, I shot 10 rounds at my paper target which is setup about 30 feet away. I was also using a rested seated shooting position with my hands and gun resting on a sandbag upfront. I did have to reset this test as one of my cameras did not cooperate the first time around and this may have effected the accuracy juts a bit as velocity spread can make the BB's spread out a bit especially high and low on target. I did get a nice 5 shot group that was in a tight under one inch group but some of the other 4.5mm Steel BB's did shot higher and lower leaving the tighter grouping.
When I put the Crosman PFAM98 Taurus PT-92 CO2 Blowback BB Pistol in full auto mode and released the last 10 or so BB's they of course sprayed the target randomly. This was expected with the heavy blowback and fast shooting.
Another Airgun Shipping Container (Sea Can) Shooting video and for this indoor filed test I put the KWC - Cybergun M45A1 1911 CO2 Blowback Airsoft Pistol through its paces.
What I am super happy about is that my Chrony Chronograph seems to be working really well as I tested a pellet, steel BB and Airsoft pistol out today and every single round through my Chrony got a reading :)
Now back to the Field Test Shooting Review at hand... I started off by placing 5 shots through my Chrony Chronograph using a brand new CO2 with .20 gram Airsoft BB's and got a really consistent reading for all 5 shots with an average of 357. The lowest shot was 353 and the fastest shot was 364 so all shots where really close in velocity. The container temperature was a near perfect shooting temperature of 23 degrees Celsius which was ideal for optimal CO2 velocity testing.
During my accuracy portion of this Field Shooting Test. I used my new seated in the back and sand bag rested up front shooting position which is about 30 feet back from my paper target. I did notice during my Chrony testing that the Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol liked to shoot a bit high, perhaps the hop-up needs a bit of twerking? So for my accuracy testing I shot at the bottom ring of the target, this helped me get more shots on the paper for sure but the Airsoft BB's still moved around a bit vertically. I was able to get about a 4-5 inch 10 shot grouping which is totally acceptable for a close range Airsoft sidearm and in an Airsoft battle I would think even shooting at about 50 feet or so I could easily hit a persons mid section consistently.
The Cybergun KWC Colt 1911 Rail Gun M45 A1 CO2 Blowback BB Pistol has a ton of blowback kick to it and a super nice single action trigger like all the KWC 1911's The modern Tactical coloration and trimmings makes this pistol a great choice as a present day side arm. It's real looker for sure with performance to match!
Well the Shipping Container Office and Airgun Shooting Range is finally all ready to use and so for this first ever airguns shooting video in it, I simply wanted to try out a couple of airguns and see how this new setup worked. I also wanted to play around with some camera position setup to see how it all looked and if there will be any additional lighting or placement considerations.
Type: Blowback Airsoft Pistol. Manufacturer: KWC - Distributed by Cybergun. Model: Colt 1911 M45A1. Materials: Almost all metal. Weight: 2 pounds (907 grams). Barrel: Metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 17 round full size metal magazine. FPS: 340+ using .20 gram BB's.
Trigger Pull: The trigger pull on the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol is what you would expect from a true single action 1911 styled pistol and typical to all the other KWC 1911's on the market. It has a short take up and then a nice light and crisp release. The working grip safety is a nice touch requiring your palm to be pressed against it for the trigger and hammer to operate..
Accuracy: At this point I have not shot the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol, I imagine it should perform well considering it has adjustable spin-up or hop-up. According to the manufacturers claimed fps, we should get somewhere in the mid to high 300 fps range using .20 gram Plastic Airsoft BB's. I'll add this one to the list of airguns I need to field test review!
Build Quality: Most KWC built full blowback airguns are built pretty well with an almost all metal build and good overall fit but sometimes the finish can wear off a bit especially in the high points. The Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol seems to have a bit heavier finish on it. I looks really good and seems to be holding up well.
Realism: The Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol is a close replica of the real steel Colt 1911 M45A1 in almost every way other than the fact that it shoot s6mm airsoft BB's rather than 45 auto bullets :) The only real notable cosmetic difference I saw was the rail having less notches in it. Other than that it is bang on including the layered grips. Available From: The Replica Airguns Store.
Pros:
All metal construction - Good weight and solid feeling gun.
Nice heavy blowback action.
Very Accurate 1911 M45A1 styled replica.
True 1911 Single action trigger, excellent pull, very smooth and light.
Accurate trigger design and working grip safety.
Lots of tactical upgrades on this version (Tac style trigger and hammer, textured grips, ambidextrous safety, white dot sights, Rail for accessories)
Love the desert tan color and layered grips.
Cons:
Sacrifice fps and shots per CO2 because of the heavy blowback but worth it.
Finish on the Cybergun and KWC guns can were off on the high points a bit but some people like the look.
Comes with the orange tip (I took mine off).
Comments:
I have always been a big fan of the KWC line of full blowback airguns and this one is no exception. It's kind of interesting that KWC does not seem to make there own blinded out versions of these guns and that a company like Cybergun is distributing them? They do look really great and this entire line with all the variations and new models will for sure keep selling these airguns. And they don't just come in Airsoft versions, I will also be taking a look at some similar 4.5mm Steel BB KWC made airguns shortly!
My Vimeo Video Review for the Cybergun KWC Colt 1911 M45A1 CO2 Blowback Airsoft Pistol:
Trigger Pull: The trigger pull on the ASG/KJWorks Beretta X9 Classic is very good in both single and double action. Double action is a bit longer and heavier than when shooting in single action since the hammer is being drawn back, but not overly heavy by any means. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the ASG/KJWorks Beretta X9 Classic CO2 BB Pistol but I did get the chance to make a short preview video where I shot the Airsoft version of this M9 Beretta at some clay pigeons setup around 20 feet away. I was able to pop the center out of the clay pigeons no problem and found that even without any practice I was consistently hitting dead center on most shots. I am not sure exactly what the FPS will be btu it shoudl for sure get at least the claimed 312 fps if not a bit more.
Build Quality: As expected, the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol build quality is just like all the other KJWorks Airsoft guns I've tested so far. The ASG 4.5mm Steel BB shooting X9 Classic has more of a Matt finish but I kind of like it, not so many finger prints on the gun. All the tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining from KJWorks.
Realism: The ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol is an excellent copy of the real steel popular Beretta M9, it is really hard to tell it apart from the real version and the ASG X9 Classic can even be field stripped in the same manor as a real Beretta M9 Semi Auto pistol with the similar functioning parts. The only missing aspect would be Beretta Licensing since the ASG version is unlicensed.
All metal design, fit and finish is very good as is with all KJWorks made guns.
Strong slide spring so should have nice heavy blowback action.
Realistic working safety and working slide catch and release.
Full size dropout metal magazine that holds steel BB's and CO2.
Can be field stripped like original Beretta M9.
KJWorks quality.
Cons:
Not licensed like the Umarex version.
None adjustable sights and white dot sights are kind of light.
Will eat up CO2 pretty quickly.
Comments:
There are very few 4.5mm Steel BB guns made by KJWorks and it seems that ASG as far as I know is the only distributer that has teamed up with KJWork to have them make some of their guns, I reviewed the ASG CZ 75 which is another ASG/KJWorks distributer 4.5mm CO2 Blowback Pistol. I don't even think you can get the 4.5mm Steel BB shooting version direct from KJWork? What I love most of all about the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol is that it is made by KJWorks since there are already a lot of Beretta M9's and Mod. 92's already out there but if I could only have one it would probably be the ASG X9 Classsic!
My Vimeo Table Top Review of the ASG X9 Classic Beretta M9 CO2 Blowback 4.5mm BB Pistol:
Last but now least to show you in this update video is the ASG CZ Scorpion EVO 3 A1. This product was developed by ASG in cooperation with CZ and is made to give the Airsoft Player the closest shooting experience they can possibly get to handling and shooting a real CZ Scorpion EVO 3 A1!
First off, I want to thank Crosman for providing these two guns for review! Now they're not exactly new guns by any means but for sure worth showing and doing some update reviews for.
Starting with the Crosman PFAM98 Taurus PT-92:
The Crosman PFAM98 Taurus PT-92 is essential a KWC made M92 also branded as the same gun as the Cybergun GSG 92 and the Swiss Arms P92.
So for all intense and purposes if you have watched any of my other revise on this line of KWC Beretta /Taurus BB pistols and even Airsoft versions then this BB gun should be really familiar to you.
History of the Taurus PT-92:
It is often referred to as a Berate 92 copy but in fact it is a Taurus PT-92 replica. The Taurus PT-92 is a product of Brazil, Taurus actually bought the entire Brazilian Beretta factory back in 1980 including drawings, tooling, machinery, and a very experienced work force to make the guns. Taurusimmediately sought to improve on the Beretta design, resulting in the popular and acclaimed Taurus PT-92.
Specifications for the Crosman PFAM98 Taurus PT-92:
Crosman use to make a similar version of the Crosman American Classic P1322 called the Back Packer which had a slightly longer barrel and came with a removable stock. You can kind of replicate this gun by adding the stock but it will have a shorter barrel. Keep in mind there are a ton of mods available for this series of Crosman airguns including barrels, bolts, trigger, Internals stocks, scope mounts…
PHOTOSpecifications for the Crosman American Classic P1322:
Metal and plastic construction.
Pneumatic pump.
.22 caliber lead pellets.
Single shot bolt action.
Rifled metal barrel.
Single action only.
Up to 460fps using lead pellets (10 pumps).
1.88 pounds (853 grams)
Keep posted for my full update reviews for these airguns...
I've already done Table Top Video Review for both the ASG CZ Scorpion VZ61 and the ASG B&T BT5 AEG 6mm Airsoft Guns so make sure to checkout both those videos.
What I hav not done so far is make a Filed Test Shooting video for either gun since this winter has been rather brutal here in BC Canada. Today I did manage to get outside and put some rounds through both the ASG CZ Scorpion VZ61 and the ASG B&T BT5 AEG 6mm Airsoft Guns so at least I can report back to everyone on how they performed for me. Sorry still no actual shooting video as my outside time was kind of limited due to it still being cold, we are even expecting some more snow tonight and over the next few days and it's March!
Getting back to my preliminary shooting testing, the ASG CZ Scorpion VZ61 only shot a slight bit higher then 250 but it was the more accurate of the two AEG Airsoft Guns getting close to a 1 inch 10 shot grouping using my standard 30 foot back semi rested shooting position. It did shoot a bit low but perhaps a hop-up adjustment should fix that problem.
Next up I tested out the ASG B&T BT5 MP5 PDW Replica and it did have a little more power hitting closer to 300 fps but it was not as accurate as the CZ shooting a bit high and to the left with most shots within about 1.5 inches, still pretty decent from 30 feet back.
Overall both AEG Airsoft Guns where fun to shoot and when I did let them lose to shoot in full auto mode they performed as expected laying down a stream of Airsoft BB's till the mags where empty :)
Materials: Steel, aluminum and plastic (polymer) construction.
Weight: 3.22 pounds (1460 grams).
Length: 15.7 inches (398mm).
Propulsion: AEG.
Action: Full auto only.
Ammunition Type: 6mm Airsoft BB's
Ammunition Capacity: 90 round magazines (Comes with 2).
FPS: 360+.
Trigger Pull: The trigger pull on the RWA KG-9 AEG Airsoft Machine Pistol is what you would expect form an AEG pistol as it is basically an on/off switch. Since the RWA KG-9 AEG Airsoft Machine Pistol is full auto only it is not easy to shoot a single shot, it can be done with a very short trigger pull but even then you get the occasional multiple shot. The RWA KG-9 AEG Airsoft Machine Pistol like the real steel original version is full auto only and that's what makes it so fun!
Accuracy: I did get a chance to take the RWA KG-9 AEG Airsoft Machine Pistol outside and put some rounds through my Chronograph and down range at a paper target. I averaged just under 340 fps using .20 gram 6mm Airsoft BB's which is about perfect for this compact machine pistol. I also placed about 10 rounds down range 30 feet back using my standard semi rested shooting position while trying to shoot in semi auto and got a pretty decent 1.5 to 2 inch grouping that was a little high but well centered left to right. Elevation could be adjusted using the hop-up.
Build Quality: The RWA KG-9 AEG Airsoft Machine Pistol is really one of the best made Airsoft guns I have seen in a while, all the metal parst are going to be real steel or aluminum, not your standard zinc alloy found in most airguns these days. The full upper is stamped steel along with the 90 round magazines, the lower is plastic with a few aluminum parts here and there. The fit and finish is also excellent!
Realism: The RWA KG-9 AEG Airsoft Machine Pistol is a replica of the Swedish made Interdynamic KG9 Open Bolt SMP, not the ntratec Tec-9 which was the American version of the KG9. For the most part the RWA Airsoft version is exact with the exception of the barrel shroud being slightly longer to accommodate the 7.4v LiPo batteries.
Pros:
Lots of steel in this gun including full upper, barrel, pins and magazines.
Very high quality build with a solid weight and excellent fit and finish.
Fairly high rate full auto fire.
Comes with battery and two magazines.
Has almost perfect usable working rate of fire averaging around 340 fps with decent overall accuracy.
Working cocking handle.
Fully Licensed.
Cons:
No blowback but there is some recoil feel from the heavy spring action.
No semi auto mode, full auto only.
Sights are not adjustable, can only use hop-up to adjust elevation.
Limited on battery choices.
Comments:
The RWA KG-9 AEG Airsoft Machine Pistol is a really cool looking Airsoft gun, it is a bit larger than most hand guns but could still be used like one since it does not have a stock and can be used for similar shooting situations. The advantage is you have 90 rounds of full auto ammo at your disposal in a size format that is super compact and easy to manoeuvre. You also get some pretty decent power for longer range shooting and the accuracy out of the box at a variety of ranges is also really good. You could even use the RWA KG-9 AEG Airsoft Machine Pistol easily as a primary or even kick ass backup gun as it is super versatile.
Watch my Vimeo Table Top Review of the RWA KG-9 AEG Airsoft Machine Pistol:
This year at SHOT Show 2017 in Las Vegas, I found there wasn’t a lot of new Airgun products but as always there are some that stood out for me. If you want more info on each Airgun Company then make sure to watch my full interviews for this years SHOT Show 2017. So without prolonging this video any longer let’s get right into it…
Umarex Legends MP CO2 Full Auto German MP40 Replica Machine-gun:
What’s not to like about the Umarex Legends MP? It has lots of metal parts weighing in at 7.7 pounds, a 60 round steel BB magazine with a dual 12 gram CO2 system. You also get your choice of shooting either in semi auto or full auto at up to 400 fps. Personally the Umarex Legends MP was the most interesting Airgun at the show this year for me and I really think it is going to be a hit!
Umarex SA10 Blowback Pellet and BB CO2 Pistol:
Another interesting product from Umarex this year was the SA10, I am not really sure what it is exactly styled after, it’s more of a futuristic looking gun with slide venting and a thread barrel for adding a mock suppressor or compensator. What appealed to me most about the Umarex SA10 was the new magazine design that incorporates a full size drop out metal magazine with 4 rotary 8 round magazines that can be loaded with either pellets or BB’s. When you empty one 8 shot magazine you simply drop the entire mag out and swap your empty 8 shot rotary magazine for a full one. The SA10 has a nice weight of around 2 pounds and shoots up to 426 fps.
Sig Sauer ASP P320 CO2 Blowback Pellet Pistol:
Sig Sauer introduced their new Sig Sauer ASP P320 CO2 Pellet Pistol this year that will be replacing the P250. Like the P250 the Sig P320 has a metal slide and polymer frame but instead of a double sided 16 shot rotary magazine, the Sig ASP P320 has a newly designed and very unique 30 round belt fed magazine. That’s nearly double the capacity without having to flip the magazine around part way through shooting. It’s great to see innovations like this happening in the airgun market.
Crosman Remington 1875 Shell Loading CO2 Pellet and BB Revolver:
Crosman introduced their own Single Action Old West Revolver this year in the form of the Remington 1875. Like the super popular Umarex Single Action Army Revolvers, the Remington 1875 is also shell loading and uses 12 gram CO2. You have the option of shooting either Pellets or BB’s out of its smooth bore barrel. I expect the Crosman Remington 1875 Shell Loading Revolver to be another popular Old West Airgun Revolver.
Crosman PSM45 Single Shot Spring Powered BB Pistol:
The Crosman PSM45 at first glance may not seem that interesting, after all it’s all plastic on the outside and only shoots about 200 fps! On the plus side it kind of looks like a Glock and we all know how hard it is to find airguns these days that resemble a Glock. I also like the fact that there is no need for any CO2, and most springers out there look like springers while the Crosman PSM45 looks like a real semi auto pistol. The PSM45 even has pretty decent weight to it since there are lots of internal metal parts and a full size drop out metal magazine which was a real surprise in such an entry level low cost pistol. If you’re looking for a fun inexpensive replica plinker than the Crosman PSM45 should fit the bill. On a side not the PSM45 would also make a really great low cost prop since the slide does work and it has that full size drop out magazine!
ASG Dan Wesson 715 2.5 and 4 inch Shell Loading CO2 Revolvers:
The ASG Dan Wesson Revolver has always been a popular choice, and then the Dan Wesson 715 came out improving on the design by adding extra weight and smoothing out the mechanics. How do you top that? Well by giving us some more options like barrel lengths. You now have your choice of a 2.5, 4 or 6 inch barrel for the Dan Wesson 715 and of course you will be able to buy your 715 pick in 4.5mm Steel BB, 6mm Plastic Airsoft or .177 Caliber Pellet ammunition versions. My personal choice may be the 4 inch Dan Wesson 715 since it has the addition of an integrated accessory rail machined into the outer barrel for lasers or tach lights.
Gletcher M1944 Mosin Nogant CO2 BB Rifle:
The Gletcher M1944 Mosin Nogant CO2 BB Rifle is not a new replica gun this year but it has been a hard one to get your hands on. In fact up until SHOT Show 2017 I had never seen one in person and so the Gletcher M1944 is new to me. I was very impressed with the quality of the Gletcher M1944 Mosin Nogant, it has a lot of metal parts including the swing out bayonet and even the simulated wood stock looks like real wood. I even had to take a second look and ask before confirming that the stock is in fact plastic on the Gletcher M1944 Mosin Nogant. I am looking forward to reviewing this rifle in the future when I do finally get one!
Of course there where other interesting products at SHOT Show 2017 this year but those are the products that stood out the most for me. Again make sure to watch my full interview videos to find out more about all the new products at this years SHOT Show.
My last Interview for SHOT Show 2017 in Las Vegas, well at least till next year and I am already looking forward to going back and doing it all over again :) I met with Boris Shekhman from Gletcher and Boris showed me several of their Gletcher Airguns along with a new accessory introduced this year.
Probably the highlight at the Gletcher booth was the Gletcher M1944 Mosin Nagant CO2 4.5mm Steel BB Bolt Action full stock air rifle! I already reviewed the Gletcher M1891 short stock version but have been really looking forward to seeing the Gletcher M1944 Mosin Nagant in person. Interestingly, Boris was asked by the SHOT Show staff to remove the Gletcher M1944 Mosin Nagant from his display because the real metal swing out bayonet was a concern for them. Boris was kind enough to bring out the Gletcher M1944 for me to see and video for everyone. The full stock however is not real wood but you need to look super close to figure this out as the reproduction is incredible.
We took a look at another Gletcher Airgun I have reviewed in the past, the Gletcher NGT and Gletcher NGT R which are very acurate Steel BB and Pellet shooting reproductions of the Belgian Nagant Revolver. Both these BB and Pellet shooting NGT's are getting a slight make-over with the addition of a safety on them, the real steel versions do not have a safety but some dealers felt it was a concern so Gletcher moving forward will be including a safety on all new NGT's. So if you want a more original Gletcher NGT Nagant Revolver then hurry up and pickup the older non-safety versions while they are still available!
Last on the list of new products from Gletcher are some really great looking leather holsters that not only work for several Gletcher airgun products but can also be used for the same real steel versions. Some of the pistols these new leather holsters will accommodate are the Gletcher TT Tokarev, 1911, Grach, PM 1951 Makarov, and the Stechkin.
Enjoy my latest SHOT Show Interview with Jesse Caster from Crosman. Jesse shows me Crosman’s latest old west single action revolver, the Remington 1875 which shares a lot with the super popular Colt Single Action Army revolvers. Jesse also goes over some new airgun pistols with me, a CO2 powered non blowback 1 to 1 replica of the Remington RP45, a very interesting single shot spring piston “Glock-ish looking pistol called the PSM45. And last but not least, Crosman has now got on the Beretta / Taurus bandwagon and added the PFAM98 to their lineup.
Crosman’s new Remington 1875 should be a welcome addition for anyone looking to add something new to their Old West Airgun lineup. The Crosman Remington 1875 like the Colt Single Action Army Revolver is shell loading, shoots in single action only and has that super slick ratcheting cylinder we all love. The Crosman Remington 1875 shoots both .177 caliber pellets and 4.5 mm steel BB’s from its smooth bore barrel, but Jesse has gone on record to claim that the pellets work well and shoots pellets and BB’s accurately at ranges typical for this type of Airgun.
Another Remington Licensed Airgun from Crosman this year is the Remington PR45. The PR45 is a 1 to 1 replica of the real steal Remington RP45 but in a CO2 non-blowback 4.5mm BB shooting version. The Crosman PR45 has a metal slide and polymer frame with a drop out all metal stick magazine. Some other notable features for the Crosman PR45 are a working trigger safety and white dot sights front and back.
If you are looking for something a little different from Crosman this year then checkout the single shot spring piston PSM45. This super affordable air pistol kind of looks "similar" to a Glock and lord knows how many times I get asked what is available in an airgun that resembles a Glock. The Crosman PSM45 is not going to win any fps awards (shoots around 200 fps), but there is no need to buy any CO2 and you can shoot this airgun in virtually any temperature for only the cost of steel BB’s. The frame and slide on the Crosman PSM45 are plastic but it does have decent weight do some internal metal parts and an unexpected full metal full size drop out magazine.
Crosman this year is adding a Beretta/Taurus full metal and full blowback CO2 BB Pistol to their product lineup. You may have already guessed it, it’s essentially a KWC Beretta / Taurus which really isn’t a bad thing since the KWC Blowback Beretta / Taurus has been very popular with replica airguners. A nice little treat with the Crosman PFAM98 Beretta / Taurus is that right out of the box it shoots in both semi and full auto using the ambidextrous selector safety switch.
Another SHOT Show 2017 interview video, this interview is with Bob Li from ASG (Action Sport Games), Bob shares with me some updates to the super popular Dan Wesson 715 along with the reintroduced EVO Scorpion Inferno powered Airsoft Rifle. Bob finishes up with a new X9 Classic which is a Beretta M9 in 4.5mm Steel BB.
You may have thought the Dan Wesson 715 was already pretty much perfect as is so what could ASG to make it even better? How about different barrel lengths. ASG has introduce the Dan Wesson 715 in both a new 2.5 inch and 4 inch version. Both lengths will be hitting stores shortly and will come in .177 caliber pellet and 4.5mm steel BB options. 6mm Airsoft will be out later on. The 4 inch version also includes an integrated accessory rail machined into the outer barrel for those of you wanted to add items like lasers and tactical lights to your Dan Wesson 715.
Last year at SHOT Show ASG introduced the EVO CZ Scorpion 3 A1 Inferno powered Airsoft Rifle but is again reintroducing it this year since they decided to take their time and get it perfect before releasing it in stores this March. The EVO CZ Scorpion 3 A1 is Inferno powered using an HPA system with a custom chip set that allows for a three round burst option an empty magazine detection.
ASG has sourced out not just any 4.5mm Steel BB shooting M9, they are actually getting their new ASG X9 Classic built by KJWorks. KJWorks is known for their Airsoft guns and I have reviewed several of them to date. If you have been looking for a KJWorks M9 but would prefer it to be in 4.5mm Steel BB then the new X9 Classic 4.5mm Steel BB KJWorks M9 exclusive to ASG is where you can get one!
