A bit of a heads up, one of our most poplar BB and Airsoft Pistols, the Dan Wesson line is for the most part fairly well stocked right now in the Canada Replica Airguns Store and ready for the Christmas rush! With that said don't hold off too long because we always run out of at least a few of the most popular versions...
Buy Dan Wesson BB Revolvers in Canada - Buy Dan Wesson Airsoft Revolvers in Canada
Type: Airsoft AEG.
Manufacturer: Bolt Airsoft.
Model:B4A1 with BRRS (Bolt Recoil Shock System).
Materials: Metal & Nylon.
Weight: 6 pounds.
Barrel: 15 inches, metal.
Propulsion: AEG with BRSS
Action: Semi/full auto, single action.
Ammunition Type: 6mm Plastic Airsoft BB (recommended .20 gram plus).
Ammunition Capacity: 300+ round magazine.
FPS: 366-400.
Trigger Pull: The trigger pull on the Bolt Airsoft B4A1 is fairly short and light as it is essentially just an on off switch for the internal electronic components. You can shoot this gun very quickly in semi auto mode, and of course in full auto when full auto position is selected. As is with all AEG rifles there is a bit of a delay while the spring is retracted and released, this is not as noticeable in full auto.
Accuracy: I tested the B4A1 Airsoft rifle by putting around 10 rounds into a target from 30 feet with .36 gram Airsoft 6mm BB's while using a semi rested position (sand bag in the front - standing in the rear). I used a non-magnified red dot scope for this test rather than using the built in iron sights. I got very good result in semi auto and even with the recoil making my sights jump around a bit in full auto still stayed well centered on target and got about a 1.5 inch group in both semi and full auto. My chronograph testing with lighter .20 gram BB's resulted in a 421 fps 5 shot average.
Build Quality: The Bolt Airsoft B4A1 Metal AEG Carbine is very well made with a full Metal upper and lower receiver, along with metal and polymer parts exactly where they would be on the real steel version of an actual Colt M4. The only plastic or nylon components are the stocks and the grips and perhaps some internal parts. I found the adjustable stock and magazine tolerance to be tighter than my King Arms M4A1 I previously reviewed which showed the Bolt B4A1 had a bit higher quality in the workmanship, for the most part the fit and finish was very good!
Realism: As with many Airsoft guns, there is great attention to realism and the Bolt Airsoft BRSS B4A1 Carbine is another great example of an Airsoft Carbine based on the Colt M4 platform. It is an AEG but because of the BRSS (Bolt Recoil Shock System) you get a very nice compromise between a conventional AEG and a GBB (Gas Blow Back Airsoft) gun. In other words, like a standard AEG I get that endless stream of consistent BB's flying down range on target but unlike a true Gas Blow Back Airsoft gun, I don't get that drop off in power and limitation to about 30 usable rounds per magazine . What I do get similar to a GBB is that recoil action that helps make the shooting experience so much more believable! Even the sound from the Bolt B4A1 is much snapper than a standard AEG and more like a GBB. I also like the fact that the charging handle and forward assist work similarly to a real M4 and also the dust cover cleverly exposes the bolt and internal hop-up for easy adjustment along with the bolt cycling just like a GBB rifle would cycle which is similar to a real steel M4.
Purchased From: The Replica Airguns Store.
Pros:
Great attention to detail with lots of working parts.
All Metal upper and lower receiver, lots of metal parts throughout.
Semi auto & full auto selectable.
High capacity 300+ round magazine.
Removable carry handle with Weaver/Picatinny rail underneath.
Nice high 420 real FPS.
Extremely accurate for plastic BB's.
Fully adjustable sights with two position Peep sights.
6 position adjustable stock.
Easy access to internal hop-up system.
Realistic Blowback Recoil system (BRSS) for a very believable shooting experience!
Cons:
May not get off as many shots per battery charge as a traditional AEG because of the Bolt Recoil Shock System.
Does not come with battery or charger but most higher end AEG's also do not.
Not yet readily available in Canada, maybe we can change that :)
Comments:
The Bolt Airsoft B4A1 Blowback Airsoft Carbine is a great compromise for the avid Airsofter looking for a practical skirmish weapon, but also craving the realistic experience of having blowback with recoil which up until now was really only provided by Gas Blow Back systems. I really like this concept and find it great fun to shoot even if its just for plinking in the yard. The overall quality is very good and you just have to love the M4 platform it's based on. If you're into customizing you can mix and match many external and internal parts with other existing Airsoft mechanical parts and I would imagine real steel accessories. I like mine as is with my addition of a riser and Red Dot and if I every get a chance to get out for a skirmish this will be my weapon of choice for sure!
I got a few sample products I wanted to quickly share with everyone :) First off Bolt Airsoft, a Taiwanese based company, sent me one of their B4A1 (M4A1 Copy) AEG Airsoft rifles featuring BRSS - (Bolt Recoil Shock System) which has Blowback with simulated recoil.
The Bolt B4A1 is designed after the M4A1 and looks and works like most AEG Airsoft rifles giving you sustained performance and the use of high capacity magazines but Bolt has added their BRSS - (Bolt Recoil Shock System) which gives you the feedback and recoil you would normally only get with a true GBB (Gas Blow Back) Airsoft gun.
I will be doing a full review very shortly so watch for it!
I also received from ASG (Action Sport Games) a few Mock Airsoft Suppressors, all of them are B&T (Brügger & Thomet) derivatives. It was nice that they sent me the version (MP9 QD) that fits perfectly on my ASG/KWA MP9. The other tow are the ROTEX-IIIA and ROTEX-IIIA Compact that fit perfectly on to a standard flash hider and even include one with them.
Check out my Vimeo Preview Video of these Review items from Bolt Airsoft and ASG:
Type: Airsoft Machine Pistol.
Manufacturer:ASG.
Model: ASG/KWC MP9 A3.
Materials: Metal & plastic.
Weight: 3.9 pounds.
Barrel: 5.5 inches, smooth bore.
Propulsion: GBB - Gas Blowback.
Action: Semi-full auto selectable SAO.
Ammunition Type: Airsoft 6mm Plastic BB's.
Ammunition Capacity: 48 rounds.
FPS: Up-to 375.
Trigger Pull: The trigger pull on the ASG/KWC MP9 A3 is single action only as the charging handle has to be pulled back to open and release the bolt for the first shot. There is a trigger safety but it is not noticeable when shooting this Airsoft machine gun. There is a short take-up and then a light release and short reset.
Accuracy: Right away I put my NcSTAR 1x25 Red Dot sight on the ASG/KWC MP9 A3 as it was a perfect fit for this small and compact machine pistol, it did not take long to sight it in and I was able to get decent accuracy in both semi auto and full auto burst due to the mild but very fast cycle rate. I was able to get a 2 inch grouping at 30 feet out using a rested position. In full auto mode the grouping did not really get too much wider. I also got between 350 and 370 fps when testing the ASG MP9 on my Chronograph.
Build Quality: The ASG/KWC MP9 A3 Airsoft Machine Pistol is built very well, using similar components that you would find on the real steel version so yes it has a plastic shell but that is to be expected. The ASG/KWC MP9 A3 does use lots of metal where it needs to be like in the internal parts, pins, bolt, barrel, rails and even the magazine. The fit and finish is near perfect!
Realism: I have to say the ASG/KWC MP9 A3 is pretty much a bang on copy of the real steel Brügger & Thomet MP9 A3. The only telltale sign is the ASG branding on the right side along with the 6mm caliber beside the ASG logo. One other small detail is the magazine which is metal on the Airsoft version where as you would find the real version uses a transparent polymer magazine.
Available at the:Canada Replica Airguns Store.
Pros:
Extremely fun to shoot and it sounds awesome!
Rate of fire is very fast and does not slow down much even when the gas is running low.
Good overall power for a short barreled gas blowback gun.
Very nice trigger with working trigger safety.
Excellent replica of the real steel version in just about every way.
Can add a lot of gear and make this gun your own.
Decent price for all you get out of the ASG MP9!
Cons:
Bolt didn't lock back for me when the gun got really cold?
Real magazine would actually be transparent polymer.
Comments:
I really like the ASG/KWC MP9 A3! I love the look, I love the features and the price is also really good for what you are getting. I was really impressed with the super high cycle rate and because of the small low weight bolt the gun does not move around too much or slow down in rounds per minute even when you do a full mag dump. There is however just enough blowback recoil to give you that GBB realistic feel! I also found that the magazine holds a lot of gas so it is possible to get two magazine worth of shots out of a single fill, that's around 100 shots. I also like how easy it is to add to the ASG/KWC MP9 A3, I had mine pimped out and looking amazing right away and suggest if you get one you do the same :)
My Vimeo Video of the ASG/KWC MP9 A3 Airsoft Machine Pistol:
This one has to be the coolest Machine Pistols out there!
Buy the ASG MP9 A3 in Canada - Buy similar Airsoft Gun in the US
Now the Thompson 1928 Tommy Gun has some company!
Buy this Airsoft Rifle in Canada - Buy similar Airsoft Rifles in the US
Type: Airsoft Assault Rifle.
Manufacturer:WE.
Model: G39C.
Materials: Metal & plastic.
Weight: 6.1 pounds.
Barrel: 9.5 inches, smooth bore.
Propulsion: (GBB) Gas Blowback.
Action: Semi & full auto.
Ammunition Type: Airsoft 6mm Plastic BB's.
Ammunition Capacity: 32 rounds.
FPS: Up-to 420.
Trigger Pull: The trigger pull on the WE G39C is about what you would expect from a Single action only Semi Auto rifle, it has a very slight take up and then about a 4 pound trigger pull that is crisp and smooth.
Accuracy: Out of the Box the WE G39C shot great up close and farther out, the hop-up seemed to be already dialed in, and even though I was using only .20 gram BB's which is a bit light for this gun, I still found they tracked well and stayed on target both near and far. My 30 foot semi rested testing produced a nice 2 inch grouping. Shooting the barrel out on the tactical range I did have to aim just a bit higher when back out at 60 or more feet away. Maybe a slight bit more hop-up would do the trick.
Build Quality: The WE G39C is very well made, yes it has lots of polymer but so does the real version and the plastic seems very durable, The fit and finish looked great and there is a lot of metal in and around the G39C where it would be on the real steel gun and where it is really required to be. Like the trigger, flash hider, rails, pins, switches, rear sight, magazine and most internal parts also.
Realism: I bet if you had the real G36C sitting beside the WE G39C you would be hard pressed to tell them apart? WE did a great job making this Airsoft version very believable not just in appearance but also when field stripping it and shooting it with it's heavy bolt and felt blowback recoil.
Available at the:Canada Replica Airguns Store.
Pros:
Amazing attention to detail, just like the real H&K G36C.
All metal internals and metal external mechanical parts.
Semi auto & full auto selectable.
Awesome blowback kick really hits you in the shoulder.
Field strips just like the real steal version.
Nice high 400 FPS and good accuracy near and far.
Full ambidextrous, even the charging handle can be switched side to side.
Can get up to three magazines per propane fill up.
Very well priced for how awesome it really is.
Cons:
Some people may not like that it is a polymer built gun externally but it is what it is!
And that's it!
Comments:
So far I have been impressed with We an Airsoft company, they really know how to make very realistic and high quality products. I wasn't sure if I was going to like the mostly polymer external build on this gun but the sheer quality and solid build took away any ideas that tis Airsoft gun would be anything like a toy. The WE G39C is one of the best performing GBB Airsoft guns I have tried out getting up to 90 shots per gas fill on a magazine which is very impressive. We was also able to keep the price down which means more people can get into one of the G39C's. If you've been thinking about adding one of these to your arsenal I don't see any reason why not to!
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
All references, photos and video claiming that any item in this Review/Video looks like a Glock or is a Replica of a Glock in any way shape or form have been removed from this post as requested by Glock"Renzulli Law Firm"
Type: Airsoft GBB pistol.
Manufacturer: KSC?
Model: NAME REMOVED 17.
Materials: Plastic & metal.
Weight: 1.6 pounds.
Barrel: 4 inch, non-rifled.
Propulsion: GBB - Propane.
Action: Semi auto - single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 23 round drop out all metal magazine.
FPS: Up to 330.
Trigger Pull: The trigger pull on this Mystery NAME REMOVED 17 GBB Airsoft pistol is very nice with some take-up at the beginning but once you hit the resistance part it is smooth and the release is very light. The NAME REMOVED trigger safety actually works on this model which is a nice touch!
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Accuracy: I found the (KSC) NAME REMOVED 17 to have very good accuracy, getting about a 2 inch 8 shot grouping from 20 feet out in a semi rested position (sand bag up front, standing in the back). I also put 5 rounds through my Chrony Chronograph and this Airsoft Gas Blowback pistol averaged right around 326 fps using .20 gram 6mm plastic Airsoft BB's.
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Build Quality: The (KSC) NAME REMOVED 17 Airsoft pistol uses a combination of plastic and metal and has a decent overall weight and feel to it thanks to the full size drop out metal magazine. The frame like a real NAME REMOVED is plastic but the slide and outer barrel are also plastic which on real steel NAME REMOVED would not be the case. Even so the overall weight is good and the fit and finish is very good. Even though this is a pre-owned Airsoft gun it is in as-new condition and seems to be holding up very well.
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Realism: The (KSC) Airsoft NAME REMOVED 17 is very realistic in appearance and operation with all parts working exactly as they would on a real NAME REMOVED 17. Even the trigger safety works and field stripping this Airsoft gun is the same as a real NAME REMOVED. NAME REMOVED trademarks are present throughout, the only real giveaway is the plastic slide and outer barrel but you would need to examine this gun close up to see this for yourself.
Purchased privately, check out some other Airsoft guns in the Replica Airguns Store.
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Pros:
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Cons:
Comments:
I am hoping that someone will know for sure who make this Airsoft NAME REMOVED 17 but either way it has been great playing around with it and doing my research to see if I could find out on my own. It's hard to tell you to go out and get one because I'm not sure what to go out and get at this point or even if this version can still be purchased and if so where from? All these questions... I can tell you that it's great to finally have an actual NAME REMOVED replica in my collection, I have a few NAME REMOVED-like guns but until I got my hand on this Mystery NAME REMOVED 17 GBB Airsoft pistol I really only had close proximities. So if you have the opportunity to snatch up something like this I say go for it!
Photo of Mystery KSC Removed by Request from Glock "Renzulli Law Firm"
Watch my YouTube Full Video Review of this Mystery NAME REMOVED 17 Airsoft Pistol:
Buy Airsoft Pistols in Canada - Buy Airsoft Pistols in the US
I already posted that I recently hit 10,000,00 YouTube video Views but I have been hinting about there being another Giveaway/Contest. After much thought I wanted to have a way that more than just one person could benefit from this. So I decided to list a bunch of my Canada Store products on sale. (Sorry US customers but I have a lot more restrictions in the US when it comes to what I can do with my pricing).
These Canadian sales will be in effect from now until October 10th and to make things even better, one lucky shopper during this time will get their entire order for free (This includes US Customers too).
So make sure to get in on the savings and the chance to get your order free!
In this "Update Video" I also show off some new previously owned guns added to my collection, an Airsoft ASG shell ejecting CZ 75, a no-name KSC Airsoft shooter and a Gamo Combat .177 caliber pellet revolver. And if you're into spring piston break barrel pistols, make sure to watch for my customized Exisco XSP180 .177 caliber Verminator!
Here is a sample of some of the items on sale right now...
Sorry for not posting any videos for almost a week but the kids are back to school and I was also away in Whistler on a short family get away for the first half of the week. So I thought I would put together a quick Update video to show off some new products added to the Canada Replica Airguns Store and also an upcoming product review of a Crosman Pellet Revolver.
In this video Update I show you around two KWC Airsoft pistols, the Sig Pro SP2022, and the Taurus PT 24 (24/7), both of which I just added to the Canada Replica Airguns Store. I also show you a very nice alternative to the Cybergun Sig Sauer P226 X-Five - the KWC Equivalent which almost exactly the same but with an adjustable rear sight, flared magwell and an unlicensed slide.
One air pistol I get asked to review over and over again is the Crosman 357 .177 caliber pellet revolver and so I contacted Crosman and they where kind enough to send me one for review, so keep checking back for that one, it will be coming up soon.
I also show off an assortment of Airsoft Magainzes and Airgun Magazines recently added to the Replica Airguns Canada Store.
Oh-yh, one more thing. I briefly mention an upcoming contest/giveaway that will coincide with my 10,000,000 YouTube Channel Video View that should be happening in the next couple of week!
Watch my Vimeo Video of this Update Video:
Another nice example of a lower cost Airsoft gun from KWC, this KWC (Taurus PT24) 24/7 in 6mm Airsoft is very similar in construction to the KWC SP2022 with an all metal slide and full size drop out magazine. The 24/7 has a nice smooth double action trigger and comes with rubberized grips.
I have been selling the Cybergun 4.5mm Steel BB version of this fine Sig Sauer copy for some time now (that is when I have it in stock) The KWC Sig Suer SP2022 is pretty much the exact same gun but chambered in 6mm Airsoft and without andy licensing or branding on the metal slide. It really is a very nice low cost Airsoft gun with full metal drop free magazine and metal slide.
Type: 6mm Plastic BB Airsoft Pistols.
Manufacturer:KJWorks.
Materials: Metal slides & frames.
Weight: 2/2.1/2 pounds.
Barrel: Metalnon-rifled smooth bore.
Propulsion: 12 gram CO2.
Action: Blowback, Single action only on KP-07 - Single/Double action on KP-02 & Elite 1A
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 20/22/20 rounds.
FPS: 366+ fps.
Trigger Pull: The trigger pull on all of these KJWorks Airsoft guns is very nice in both single and double action, The KP-07's true single action only 1911 trigger is a beauty, with no take up at all and a very light and smooth release. The Beretta Elite 1A is the next best with a surprisingly light weight double action trigger. All of these guns will be shooting primarily in single action as the blowback precooks the hammer with each shot.
Accuracy: I shot all of these fine KJWorks Airsoft guns from 20 feet out in semi rested position and got very similar results. I was able to place 10 rounds in a 2 to 2.5 inch grouping for all guns, with the KP-07 1911 shooting the most well centered. The Beretta Elite 1A shot well centered also but just a hair under center mass while the KP-02 seemed to shoot low but could be adjusted to shoot higher by increasing the hopup. All three KJWorks Airsoft pistols got right around the 330-350 fps mark (5 shot average chrony testing) with the KP-7 1911 and Elite 1A Beretta hitting the higher end and the KP-02 Sig P229 getting right around 330fps. All three KJWorks Blowback Airsoft guns should be able to hit 366+fps in the right shooting conditions.
Build Quality: I was extremely impressed with the build quality of these KJWorks Airsoft guns, the fit and finish is the best I have seen on any of my guns including Airguns also. Even after shooting several magazines worth of BB's, the painted metal friction areas did not seem to show nearly as much wear as some of my other blowback guns. The tolerances between the moving parts like the slide and frame are very tight showing excellent workmanship and machining with these KJWorks Airsoft guns.
Realism: All of these KJWorks 6mm Airsoft pistols are based on real steal versions of the same guns (KP-02 is a Sig Sauer P229 copy, the KP-07 is a Colt 1911 copy and the Elite 1A is a Beretta Copy). They are very good replicas even though the KP-02 and KP-07 do not have any specific licensing on them. The Elite 1A does have licensing which is a plus. The only negative thing I can think of is the fact that the KP-02 has the rather unusual CO2 magazine that sticks out of the bottom of the handle that is not at all like a real P229 magazine. I do believe you can find a GBB magazine that would be much more in line with the real steel version of this magazine.
Available in the:Replica Airguns Store
Pros:
All metal guns with good overall realistic weights.
Very heavy blowback on all guns, especially the KP-07 1911
Excellent fit and finish - best I have seen.
Nice mid range fps - great for on the field.
Very consistent accuracy for all KJWorks Airsoft guns.
Very believable replicas of the real steel versions.
Cons:
KP-2 and KP-07 did not have official licensing.
All seem to go through CO2/Gas fairly fast.
KP-02 had a rather strange looking CO2 magazine.
KP-02 slide did not lock back after last shot, may be due to CO2 magazine configuration.
Comments:
I guess you get what you pay for, these KJWorks Airsoft guns do fetch a bit higher price but when you take them out of the box and really look at them closely you can see why, they are pretty much flawless and the fit and tolerances are very good with very little play in the mechanical parts. Shooting these guns is just as wonderful, they all worked very well and got consistent accuracy and fps between shots. There where no ammo loading problems and no unexpected behaviors with any of these Airsoft pistols. If you can afford to pay that little bit more for one of these very high quality KJWorks Blowback Airsoft guns, you will not be let down!
Here is a short video update along with a few photos of my KWC and Umarex Airsoft Pistols recently added to the Canada Replica Airguns Store. The models showcased are the KWC M1911 & KWC M92 (PT99) along with the Umarex Walther P99. All of these pistols use 6mm plastic Airsoft BB's, shoot over 366 fps using CO2 and have blowback operation.
Watch my Vimeo Update Video on these three Blowback Airsoft Pistols:
Last but not least for now, just added to the Canada Replica Airguns Store - the KWC M92 (PT99) CO2 Blowback Airsoft Pistol.
The KWC M92 (PT99) is essentially is the Airsoft KWC version of the Cybergun GSG 92 without any branding and also in 6mm Airsoft caliber. And it comes already to shoot in either semi or full auto so no modifications required!
Buy This Airsoft Pistol in Canada - Buy KWC Airsoft guns in the US
KWC Tanfoglio Witness 1911 Airsoft clone Added to the Canada Replica Airguns Store.
The KWC M1911 is essentially is the Airsoft KWC version of the Cybergun Tanfoglio Witness 1911 without any branding and also in 6mm Airsoft caliber.
Buy This Airsoft Pistol in Canada - Buy KWC Airsoft guns in the US
Another Blowback Airsoft pistol added to the Canada Replica Airguns Store and this one won't break the bank!
The Umarex Walther P99, one of Walther's most popular semi auto pistols. This CO2 powered Airsoft version captures the realism with its BLOWBACK, semi-automatic action and full metal slide.
Buy this Airsoft Pistol in Canada - Buy this Airsoft Pistol in the US
Type: Airsoft Pistols.
Manufacturer:KWC.
Model:Desert Eagle .50 & Sigma SW40F.
Materials: Metal slide & polymer frame.
Weight: 2.5/1.8 pounds.
Barrel: Metalnon-rifled smooth bore.
Propulsion: 12 gram CO2.
Action: Blowback, single action only.
Ammunition Type: 6mm plastic Airsoft BB's.
Ammunition Capacity: 21/22 rounds.
FPS: 400/390.
Trigger Pull: The trigger pull for both KWC blowback single action pistols is very good, the Desert Eagle is a bit better with less play and a lighter pull while the Sigma SW40F still feels very good but has a little bit more take up and a slight bit more pull required.
Accuracy: I shot both guns from 20 feet out in semi rested position and got similar results. I was able to place 10 rounds in a 2.5 to 3 inch group and both guns shot well centered. I have full confidence that I could easily hit a man sized target from 50 feet away. Both KWC Airsoft pistols got right around 400 fps (5 shot average chrony testing) with the Desert Eagle only 10 fps higher than the Sigma SW40F and this was using .20 gram plastic Airsoft BB's.
Build Quality: The build quality for both guns is pretty much the same, both have a metal slide and barrel with a polymer frame and plastic grips, the Sigma SW40F had a plastic magazine release and trigger while the Desert Eagle used metal in these parts. The KWC Sigma SW40F seemed to wear a bit better as the painted finish seemed more durable. I found the metal on metal areas on the Desert Eagle where losing the paint and also in some of the high spots. Over all the guns worked very well and had good fit and finish.
Realism: The KWC Desert Eagle .50 and Sigma SW40F are very accurate replicas of their real steel counterparts, with the Desert Eagle also having the full licensing on it for added authenticity. The workings of both Airsoft guns are pretty much just like a real gun with full size drop out magazines and very heavy full blowback operation. The slides on each gun give a nice metallic sound when operating.
Available in the:Replica Airguns Store
Pros:
Lots of metal and good overall weight.
Very heavy blowback on both guns
Good fit and finish.
Excellent fps.
Good accuracy with both guns.
Very believable replicas of the real steel versions.
Cons:
Paint wear in high spots noticeable on the Desert Eagle.
Non adjustable sights.
Both go through CO2 fast.
No trademarks on the Sigma SW40F.
Comments:
It's wonderful to get these KWC blowback Airsoft guns here in Canada finally and have the ability to review them for everyone. They remind me a lot of the Cybergun 4.5mm Steel BB blowback pistols very much and this is probably because there are Airsoft version of these guns also distributed by KWC. Whether you want one of these very nice Airsoft pistols for plinking and target practice or to use in battle on the Airsoft field, either gun would make a great choice. I am really loving the fact that I now have more guns I can review and Airsoft or 4.5mm Steel BB it really doesn't matter to me, I'm having way to much fun to care ;)
Last update for the day, I am happy to announce that I have added two Gas Blowback Airsoft Rifles from WE to the Canada Replica Airguns Store. They are both fantastic guns that are the spitting image of their real steel counterparts and both have awesome blowback action and feel. Both rifles shoot in semi and full auto which is exhilarating!
WE G39C (H&K G36) Open Bolt GBB Reinforced Airsoft Rifle
Some more asked for blowback Airsoft pistols just added to the Canada Replica Airguns Store, these three are from KJWORKS and are very high quality for sure with excellent fit and finish on them!
KJWORKS P229 KP-02 Full Metal CO2 Blow Back Airsoft Pistol
KJWORKS MEU KP-07 Full Metal Gas Blow Back Airsoft Pistol
