I wanted to compare the KWC/Cybergun PT 24/7 G1/G2 BB and Airsoft Pistols to each other in the Replica Airguns Indoor Airgun Shooting Range to see how they compare side by side not only in terms of accuracy but also what their Feet Per Second Velocity performance would be.
Like all my Field Test Shooting Videos I place 5 rounds through my Chronograph and average out the fps to see what their real world velocity is using a brand new CO2 along with standard 4.5mm Steel BB’s and .25 gram 6mm Plastic Airsoft BB’s. I then place a paper target 30 feet down range and proceed to put 10 rounds from each gun into a fresh paper target to see not only how close the Airguns shoot to the bullseye out of the box but also how close each 10 round grouping is.
All of the KWC Cybergun Taurus PT 24/7 G1/G2 BB and Airsoft Pistols performed fairly well, the KWC PT 24/7 G1 NBB Steel BB Pistol as expected had the highest velocity at close to 400 fps while the KWC PT 24/7 G2 Blowback Airsoft Pistol with the slightly heavier then normal Airsoft Plastic BB’s shot closer to 300 fps. The KWC PT 24/7 G2 Blowback Steel BB Pistol shot just over 300 fps.
In terms of accuracy The KWC PT 24/7 G1 NBB Steel BB Pistol had one of the tighter grouping close to 2 inches but shot a fair amount to the left of the bullseye. The KWC PT 24/7 G2 Blowback Airsoft Pistol shot well centered left to right but low on the target with a spread of just over two inches and the KWC PT 24/7 G2 Blowback Steel BB Pistol was the most centered on target getting again close to a two inch grouping.
I do like the KWC Cybergun Taurus PT 24/7 G1/G2 BB and Airsoft series of Airguns and personally prefer the newer Blowback G2 models but to each their own.
When we have multi potions for a specificities model of Airgun I like to compare them to each other to understand the similarities and differences of each Airgun. Often time the differences are as simple as what ammo they use, if they have licensing or not, who they are distributed through, slightly model revision and of course some cosmetic differences.
In this YouTube Video Comparison I lock at the the KWC Cybergun Taurus PT 24/7 G1/G2 BB and Airsoft lineup and go over their similarities and differences so you can decide which one may be right for you.
At one point in time the KWC Cybergun Taurus PT 24/7 G1/G2 BB and Airsoft Pistols came in these version:
In this Field Test Shooting Video I test out the G&G SMC-9 GBB Airsoft Carbine in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see if the real world performance matches the manufacturers claims. I first place 5 rounds through my Chronograph using .25 gram Airsoft BB’s with a fully gassed up extended magazine to find out what the actual FPS is. I then shoot 10 rounds from a seated and rested shooting position into a fresh paper target setup 30 feet down range to see just what we can expect and then just for fun I shoot the 40 rounds left in the 50 round magazine in full auto to see how this also effects accuracy.
Starting with my Chronograph test, the G&G SMC-9 GBB Airsoft Carbine averaged 339 FPS with the fastest shot recorded at 350 fps and the slowest being 324 fps, so very consistent in terms of sustained fps during my Chronograph velocity testing. The velocity was a bit under the claimed 366-375 fps but I was using slightly heavier BB’s and it wasn’t super warm temperatures in the Sea Can on this testing day, around room temperature, (20 degrees Celsius or 68 degrees Fahrenheit).
Moving onto the accuracy testing for the G&G SMC-9 GBB Airsoft Carbine, it performed pretty decent shooting about a 10 round 4 inch grouping but if I removed two flyers top and bottom the grouping would have been loser to 1.5 inches. The grouping was well centered on the target but I did adjust the sights up a bit as initially out of the box the G&G SMC-9 GBB Airsoft Carbine was shooting fairly low at 30 feet out. The good news is the G&G SMC-9 GBB Airsoft Carbine has fully adjustable sights for windage and elevation along with the 120 clicks of hop-up adjustment. When it came to my full auto testing I found I was shooting really low, perhaps from the blowback recoil pushing me of target? This was the case at least when I did a 40 round mag dump. When I performed the test using shorter bursts I was able to keep more rounds centered on the target for sure but accuracy in full auto was not nearly as good as in semi auto because of the heavy blowback.
Over all the G&G SMC-9 GBB Airsoft Carbine performed decent for me, the velocity was bang on right around what is claimed by G&G allowing this GBB Airsoft Carbine to shoot targets at further out ranges. Accuracy in semi auto was also very good but again shooting in full auto will take a bit more of your attention keeping the blowback recoil under control, for this reason burst fire in full auto will give you better accuracy which is more than likely how you would be shooting the G&G SMC-9 GBB Airsoft Carbine anyways. I really like the diversity you get with the G&G SMC-9 GBB Airsoft Carbine and if you are into Gas Blowback Airsoft guns, then I feel you get similar performance to an AEG but with a lower capacity magazines, but then again I may just have to get my hands on a drum magazine for the G&G SMC-9 GBB Airsoft Carbine and see how that changes things.
Type: Gas Blowback Airsoft Carbine. Manufacturer: G&G Model: SMC-9 Materials: Metal/Aluminum & Polymer. Weight: 4.7 pounds (2125 grams). Length: 410/620mm folded/unfolded length Hop-up: Yes - 120 click adjustment. Propulsion: Green gas or propane. Action: Semi & Full AutoBlowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 50 rounds. FPS: 366-375 fps.
Trigger Pull: The trigger pull on the G&G SMC-9 GBB Airsoft Carbine is typical single action only with a soft short take-up and light release point. I would not call this a crips trigger since it does have a rather spongy feel to it but this is only noticeable when you are easing the trigger slowly. In reality you will be engaging the trigger quickly when shooting it on the field and won’t notice any of the creep or take-up. I would consider it to be a decent trigger pull over all.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G SMC-9 GBB Airsoft Carbine but as with most of my Full auto Airguns I find it hard not resist going outside and blasting off at least one magazine in full auto. Of course this was the case with the G&G SMC-9 GBB Airsoft Carbine and I can tell you I went through all 50 rounds in not time and the G&G SMC-9 GBB Airsoft Carbine rounds went exactly where I pointed the gun short and long range so I expect my Field Test Shooting video to produce good results.
Build Quality: The G&G SMC-9 GBB Airsoft Carbine feels amazing in the hand with a lot of metal going on in the upper Carbine conversion kit portion, the front rail assembly is CNC Aluminum and the Pop-up iron sights are actually metal. The rear fold out stock is plastic but it is sold and just like the rest of the G&G SMC-9 GBB Airsoft Carbine very well made with great fit and finish. Of course the lower polymer frame is from the G&G GTP9 and just like all of the G&G pistols is very well made.
Realism: The G&G SMC-9 GBB Airsoft Carbine genuinely feels like a real steel firearm when holding it in the hand. Shooting it feels much the same but obviously with a lot less recoil than a powder burner. Just like a real steel 9mm Carbine the G&G SMC-9 GBB Airsoft Carbine mechanically works virtually the same with working slide catch release, charging handles, magazine release, and duel safeties, all ambidextrous by the way. As expected you can fully field strip the G&G SMC-9 GBB Airsoft Carbine.
Lots of metal parts giving the G&G SMC-9 GBB Airsoft Carbine really good weigth and feel.
Fold out stock sits nice and tight using magnets when not in use.
Integrated QD sling swivel.
Comes with two different sized Back-straps to accommodate small and larger hands.
Super high capacity extended 50 round magazine that holds a ton of gas for consistent power and lots of shots per fill.
Converts the standard GTP9 semi auto pistol into a full auto Carbine.
Almost everything is ambidextrous.
CNC 20mm / MLOK Rail for lots of accessories options.
Actual metal pop-up fully adjustable sights.
Easy to adjust hop-up without disassembly.
Dual safety system, cross bolt on frame and trigger safety.
Cons:
Fold out stock is not adjustable which makes the sights are a bit tight.
Does not come with the pistol slide if you want to covert it back to the GTP9.
Comments:
I am a big fan of the full line of G&G Airsoft guns and so far their GBB pistol lineup has been a treat to review, adding their new G&G SMC-9 GBB Airsoft Carbine to the lineup for me is the perfect mix between their GBB Pistol lineup and their mostly AEG Rifle lineup. I am hoping to see if I can acquire the drum magazine and eventually see how that works with the G&G SMC-9 GBB Airsoft Carbine, for now the 50 round extended magazine will have to do. Really looking forward to testing out the G&G SMC-9 GBB Airsoft Carbine so stay posted for those results shortly!
My YouTube Table Top Review of the G&G SMC-9 GBB Airsoft Carbine:
I often have people ask me what is more powerful in terms of one gun over another and which Airguns have more raw power, BB versus, Pellet, versus Airsoft, versus Paintball?
Well in this indoor field test shooting video I compare all of the above head to head to see which Airgun not only has the most raw power but also how well they perform on a target setup 30 feet down range since after all what does it matter how powerful a gun is if it can not hit the target!
The Airguns I used in this head to head shooting performance test where as follows:
Keep in mind the ammunition for each Airgun is very different not just in terms of materials but also their weight which will have a big effect on the energy they produce. For example for this test I used 4.6 grain 4.5mm Steel BBs, 4.6 grain 6mm Aluminum Airsoft BB’s. 6.9 grain .177 cal. Lead Pellets and 17.7 grain .50 cal. Rubber Paintballs.
Watch my YouTube Video to see how well each Airgun did in this comparison shooting test!
In this Field Test Shooting Video I test out the G&G Piranha MK I & TR GBB Airsoft Pistols in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see what the real world performance is for these very similar Airsoft Pistols. I first place 5 rounds through my Chronograph for each Airsoft Gun using .25 gram Airsoft BB’s with fully gassed up magazines to find out what the actual fps velocity is. I then shoot 10 rounds from a seated and rested shooting position into fresh paper targets setup 30 feet down range to see just what we can expect in terms of accuracy from the G&G Piranha series.
Starting with my Chronograph test, a placed 5 rounds through my Chronograph with both the G&G Piranha MK I and G&G Piranha TR GBB Airsoft Pistols. Technically they should have performed nearly identical but not all guns are setup exactly the same out of the box and so the G&G Piranha MK I GBB Airsoft Pistol did shoot a bit hotter than the G&G Piranha & TR GBB Airsoft Pistol averaging 290 fps versus 257 fps. As a quick test I placed the magazine from the MK I into the TR and the G&G Piranha TR GBB Airsoft Pistol did shoot much hotter and very close to the G&G Piranha MK resultsI. I would assume the valves in these magazines where perhaps not letting out the same amount of Gas hence the difference in velocity. The velocity was well under the claimed 370+but I was using slightly heavier BB’s and it was a little cold in the Sea Can on this testing day, not quite room temperature. Around 19 degrees Celsius or 66 degrees Fahrenheit.
Moving onto the accuracy testing for the G&G Piranha MK I & TR GBB Airsoft Pistols, they performed pretty well shooting 10 round 2 inch groupings with both Airsoft Pistols shooting on the money vertically while the G&G Piranha MK I shot a bit to the left and the G&G Piranha TR shooting well centered all around.
All in both of the G&G Piranha MK I & TR GBB Airsoft Pistols performed good for me, I would have liked to have seen the fps higher since both guns where well under the claimed 370+ fps but for close quarter shooting you should have no problem with either of them and again maybe your magazine will shoot a bit hotter than mine did. The partial blowback action is snappy and quick with just enough recoil action to give that realistic shooting experience. The triggers on the G&G Piranha MK I & TR GBB Airsoft Pistols are really nice allowing for quick tight followup shots and again if you like the look and feel of a Glock but perhaps want something a bit more unique then you will want to consider one of the G&G Piranha series Airsoft Pistols know doubt.
In this Field Test Shooting Video I test out the G&G GPM92 GP2 GBB Airsoft Pistol in the Replica Airguns Indoor Sea Can Airgun Shooting Range to see what the real world performance is for this Beretta 92 styled G&G Airsoft Pistol. I first place 5 rounds through my Chronograph using .25 gram Airsoft BB’s with a fully gassed up magazine to find out what the actual FPS is. I then shoot 10 rounds from a seated and rested shooting position into a fresh paper target setup 30 feet down range to see just what we can expect in terms of accuracy from the G&G GPM92 GP2 GBB Airsoft Pistol.
Starting with my Chronograph test, the G&G GPM92 GP2 GBB Airsoft Pistol averaged 275 FPS with the fastest shot recorded at 278 FPS and the slowest being 274 FPS, so very consistent in terms of sustained FPS doing my testing. The velocity was well under the claimed 366 but I was using slightly heavier BB’s and it was a little cold in the Sea Can on this testing day, not quite room temperature. Around 19 degrees Celsius or 66 degrees Fahrenheit.
Moving onto the accuracy testing for the G&G GPM92 GP2 GBB Airsoft Pistol, it performed pretty decent shooting about a 10 round 1.5 inch grouping if I removed one flyer that pulled a bit to the left. The grouping was a little bit low but well centered left and right so even though the sights are none adjustable I should be able to pull up the shot placement a bit using the hop-up adjustment.
All in all the G&G GPM92 GP2 GBB Airsoft Pistol performed well for me, I would have liked to see the FPS just a bit higher but for close quarter shooting you should have no problem with it. The blowback action is nice and firm and the typical Beretta single and double action trigger is true to form allowing for a round in the pipe with the hammer safely decocted but ready to go with a quick release of the safety and a double action pull of the first round. The G&G GPM92 GP2 GBB Airsoft Pistol may be a bit bulky and heavy for some smaller handed shooter so keep that in mind.
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: Piranha TR Materials: Metal & Polymer. Weight: 1.5 pounds (670 grams). Length: 7.8 inches total Barrel: 4.01 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 370+ fps.
Trigger Pull: The trigger pull on the G&G Piranha TR GBB Airsoft Pistol is typical single action only with a easy short take up (some of which is the trigger safety engaging), followed by a crisp predictable light release. The quick slide cycle allows for quick semi auto shooting with the G&G Piranha TR GBB Airsoft Pistol making it a great fast action shooter with quick target acquisition between shots.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G Piranha TR GBB Airsoft Pistol but I expect it to perform similar to most G&G Blowback Gas Operated Airsoft Pistols and shoot consistently in the mid 300 fps with a 10 round grouping around 1-2 inches. Stay posted for my Field Test Shooting Video where I hope to confirm these predictions in the Sea Can indoor Airgun Shooting Range.
Build Quality: Like most off theG&G Airsoft guns, the G&G Piranha TR GBB Airsoft Pistol build quality is really nice. Fit and finish are excellent with virtually zero slide wiggle, you can also get the G&G Piranha TR GBB Airsoft Pistol in a two tone stainless slide and chrome finish barrel that looks really sharp. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust using a special tool without taking the Airsoft gun apart.
Realism: The G&G Piranha TR GBB Airsoft Pistol as far as I can determines not an exact replica of any specific real steel gun in production but it does share looks, size and feel to that of the Glock but perhaps with an even more modernized look to it. You will find realistic function to the G&G Piranha MK I GBB Airsoft Pistoling terms of it’s operation with its full blowback action, working slide catch release, magazine release trigger safety and takedown lever allowing for it to be easily and quickly field stripped.
Good balance of metal and plastic for a balanced and light feel.
Partial slide Blowback operation should allow for even better gas performance and snappy operation.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice two tone slide.
Has a working trigger safety.
Smaller spit grip perfect for people smaller hands.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
Dual 20mm top and bottom Rails for accessories.
Comes in all black and two tone black and sliver.
Comes with high quality speed loader
Threaded barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Not an actual replica of any specific gun I know of but does share some Glock attributes.
No actual frame safety other than the trigger safeties, (not always a bad thing).
Comments:
Overall I really like the new G&G Piranha TR GBB Airsoft Pistol, it has a really modern look to it yet has a familiar feel. The G&G Piranha TR GBB Airsoft Pistol is fairly light weight with that quick and snappy partial slide allowing for very quick follow up shots. Combine all of that with the new Gas saving Ceramic Whirl Cylinder Valve I expect the G&G Piranha TR GBB Airsoft Pistol to perform really well when in action. I like that you have the option of the more subdued all black version or if you like your guns to be a little bit more flashy you can also get it in the two tone with black and stainless version. The TR version over MK 1 does allow for optics on top which personally would not be my choice for this gun but it’s nice that you have this option.
My Table Top Review Video of the G&G Piranha TR GBB Airsoft Pistol:
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: Piranha MK I Materials: Metal & Polymer. Weight: 1.5 pounds (670 grams). Length: 7.8 inches total Barrel: 4.01 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single action only. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 25rounds. FPS: 370+ fps.
Trigger Pull: The trigger pull on the G&G Piranha MK I GBB Airsoft Pistol is typical single action only with a easy short take up (some of which is the trigger safety engaging), followed by a crisp predictable light release. The quick slide cycle allows for some pretty quick semi auto shooting with the G&G Piranha MK I GBB Airsoft Pistol making it a great fast action shooter.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G Piranha MK I GBB Airsoft Pistol but I expect it to perform similar to most G&G Blowback Gas Operated Airsoft Pistols and shoot consistently in the mid 300 fps with a 10 round grouping around 1-2 inches. Stay posted for my Field Test Shooting Video where I will confirm these predictions.
Build Quality: Like pretty much all G&G Airsoft guns, the G&G Piranha MK I GBB Airsoft Pistol build quality is really good. Fit and finish are excellent with virtually zero slide wiggle, the two tone stainless slide and chrome finish barrel look really good. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust without taking the Airsoft gun apart.
Realism: The G&G Piranha MK I GBB Airsoft Pistol as far as I can determines not an exact replica of any specific real steel gun in production but it does share looks, size and feel to that of the Glock but perhaps with an even more modernized look to it. You will find realistic function to the G&G Piranha MK I GBB Airsoft Pistoling terms of it’s operation with its full blowback action, working slide catch release, magazine release trigger safety and takedown lever allowing for it to be field stripped.
Good balance of metal and plastic for a balanced and light feel.
Partial slide Blowback operation should allow for even better gas performance and snappy operation.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice two tone slide.
Has a working trigger safety.
Smaller spit grip perfect for people smaller hands.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
20mm Rail for accessories.
Comes in all black and two tone black and sliver.
Comes with high quality speed loader
Threaded barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Not an actual replica of any specific gun I know of but does share some Glock attributes.
No actual frame safety other than the trigger safeties, (not always a bad thing).
Comments:
Overall I really like the new G&G Piranha MK I GBB Airsoft Pistol, it has a really modern look to it yet has a familiar feel. The G&G Piranha MK I GBB Airsoft Pistol is fairly light weight with a quick and snappy slide allowing for very quick follow up shots. Combine all of that with the new Gas saving Ceramic Whirl Cylinder Valve I expect the G&G Piranha MK I GBB Airsoft Pistol to perform really well when in action. I like that you have the option of the more subdued all black version or if you like your guns to be a little bit more flashy you can also get it in the two tone with black and stainless version.
My Table Top Review Video of the G&G Piranha MK I GBB Airsoft Pistol:
Type: Gas Blowback Airsoft Pistol. Manufacturer: G&G Model: GPM92 GP2 Materials: Metal slide & frame, real wood grips. Weight: 2.3 pounds (1040 grams). Length: 8.9 inches total Barrel: 4.6 inches,Metal non-rifled smooth bore. Propulsion: Green gas or propane. Action: Blowback, single and double action. Ammunition Type: 6mm plastic Airsoft BB's. Ammunition Capacity: 28rounds. FPS: 366+ fps.
Trigger Pull: The trigger pull on the G&G GPM92 GP2 GBB Airsoft Pistol is very good in both single and double action. Double action is a bit longer but not that much heavier when shooting in single action. Single action shooting is short, light and crisp as you would expect when shooting a real steel Beretta 92 style pistol.
Accuracy: I have not done my actual Field Test Shooting video review for the G&G GPM92 GP2 GBB Airsoft Pistol but it should perform similar to my earlier review of the G&G GPM92 GBB Airsoft Pistol where it performed fairly well shooting in the mid 300 fps with a nice under 1 inch 10 round shot placement for 30 feet down range.
Build Quality: Like pretty much all G&G Airsoft guns, the G&G GPM92 GP2 GBB Airsoft Pistol build quality is right inline. Fit and finish where excellent and a lot of attention to detail was seen all over this Replica Airsoft Pistol. It also has an updated Ceramic Whirl Cylinder Valve technology from G&G that should significantly help with freezing in colder or fast shooting situations along with a new Hop-up system you can easily adjust without taking the Airsoft gun apart.
Realism: The G&G GPM92 GP2 GBB Airsoft Pistol is an excellent replica of the real steel Beretta Mod. 92FS, the safety even acts as a working de-cocker. You'll also find 5, 10, and 15 numbered markings on the backside of the magazine that would normally indicate how many bullets are in the magazine, a nice touch for sure! Everything works pretty much the same as it would on a real Beretta M9 including the ability to fully field strip the G&G GPM92 GP2 GBB Airsoft Pistol. I like the addition of th real wood grips that are a bit thicker than the plastic ones but if you ahed decent sized hands this shoudl not be a problem for you.
Ceramic Whirl Cylinder Valve should expect to get decent amount of shots per green gas fill.
White dot sights front and back.
Nice real wood grips.
Comes with hard shell case.
New Hop-up system for quick and easy fine adjustments with no need to field strip the gun.
20mm Rail for accessories.
comes in three different color schemes. Black, Silver, Gold.
Comes with high quality speed loader
Safety also works as a de-cocker.
Threaded removable barrel tip for add on mock suppressor.
Cons:
Sights are non adjustable.
Wood grips make the grips a bit thicker than plastic grips.
Price does go up especially if yo want the silver or gold version.
Comments:
I would have to say the new G&G GPM92 GP2 is one of the nicest Beretta Model 92FS Airsoft Pistols you are going to find out there, even a step up over the previous GPM92 model. There is a ton of attention to detail for sure, You also get the hard shell case with included high quality speed loader and G&G's updated Ceramic Valve and Revolutionary Whirl Cylinder Valve that help with freeze-up issues. It’s also nice that you no longer are required to filed strip the G&G GPM92 GP2 GBB Airsoft Pistol in order to adjust hop-up and the real wood grips just really finish off this quality product from G&G.
My Table Top Review of the G&G GPM92 GP2 GBB Airsoft Pistol:
In this Preview Unboxing Video I take a look at five Gas Blowback Airsoft Pistols. Three of them are from G&G and two are from ICS. All offer full blowback operation and are green gas or propane powered with full size metal drop out magazines.
I am super excite to showcase three awesome rifles in this Update Preview Unboxing Video. Two of which are Airsoft and one is a Steel BB shooter, all of which are semi and full auto selectable. In this video I do a bit of an unboxing and preview of each Rifle not going into too much detail as I want to leave most of the information for my Table Top and Filed Test Videos. The main purpose of this video is to let everyone know we have these Rifles in our Canada Replica Airguns Store now for sale.
I may as well talk about them in the order they appear in my video so lets start with the ICS CXP APE AEG Airsoft Rifle. The ICS CXP APE AEG Airsoft Rifle is a mostly metal Electric Airsoft Rifle with realistic electronic blowback operation along with a CNC machined aluminum upper and lower receiver. It comes with a hi-cap 300 round magazine and a Ver 2 Full Metal ICS Split Type Gearbox. The ICS CXP APE AEG Airsoft Rifle weighs in at just under 3kg.
Next I showcase the G&G SMC9 GBB Airsoft Carbine, a unique product that converts the G&G GTP9 pistol into a a semi and full auto Carbine and includes a 50 round extended magazine, there is an even higher capacity drum magazine made for this product! You will find a fold out stock along with a CNC Machined MLOK Rail for additional mounting options.
Last but perhaps one that I have been the most eagerly anticipating is the Crosman AK1 CO2 Blowback BB Rifle a twin CO2 Blowback 4.5mm Semi and Full auto AK style BB Rifle, finally a decent AK BB Rifle! The Crosman AK1 CO2 Blowback BB Rifle has a claimed fps of 430 and shoots 1400 rounds per minute in full auto, very similar to the Crosman DPMS series of AR styled CO2 Blowback Full Auto BB Rifles. The Crosman AK1 CO2 Blowback BB Rifle comes with a 25 round magazine and swing out rear adjustable stock.
In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second for each shot and then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet down range followed by shoot 10 rounds back to back to see what the spread or grouping size is. I followed this up with a nice long full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the normally tested .20 in the claimed fps of over 366 fps so I was expecting to get a little bit lower velocity results. I did manage to average right around 304 fps with all shots fairly consistently with the slowest being 302 fps and the fastest hitting 305 fps.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle did shoot a little bit low close to the bottom of the rings but not as low as when I tested the Heckler & Koch HK416C version, I am sure some hop-up adjustment will get this closer to the mark. I did mange to get a really tight 10 round grouping of close to half an inch with most of the BB’s hitting one o top of the other I would ahed to say this is the best 30 foot accuracy results I have gotten from any Airsoft rifle to date! Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 2 inch opening.
The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle performed really well for me and as already mentioned is crazy accurate. It had a slightly lower fps than the Heckler & Koch HK416C version which was a bit of a surprise but at 304 fps using .25 gram Airsoft BB’s this is about perfect for close quarters shooting adn even out to medium distances. Make sure not checkout all of our Umarex VFC Heckler & Koch over in the Replica Airguns Canada Online Store.
In this Field Test Shooting Video I test out the Velocity and Accuracy of the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle by first placing 5 rounds through my Chronograph and recording the feet per second of each shot then averaging them out. For the second portion of my Indoor Shooting Performance Test I setup a paper target 30 feet away and then shoot 10 rounds back to back to see what the spread or grouping size is. I follow this up with a full auto burst just for fun to see if the grouping still remains nice and tight.
For my Velocity test I used .25 grain Plastic Airsoft BB’s rather than the .20 in the claimed fps over 366 fps so I was expecting to get a little bit slower results. I did manage to average right around 325.5 fps with all shots consistently hitting either 325 or 326 fps so super consistent.
I then setup my brand new paper target and using a rested and seated shooting position from 30 feet back I placed my first 10 rounds into the target. This is when I discovered the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle liked to shoot fairly low even when using the raised elevation option on the rear sight. Because of this I had to aim a little bit higher on the paper target to place shoots more centered. Once I figure out my aim point I did mange to get a fairly tight 10 round grouping of close to an inch with a couple of stagers pushing it out to 2 inches. Full auto was as predicted, lots of fun with a nice hole in the paper/cardboard leaving about a 3.5 inch opening.
The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performed well for me once I figured out that it liked to shoot rather low. I would suggest placing a bit of a spacer or riser under the rear sight to bring up the barrel at least for closer in shots where hop-up may not ark the Airsoft BB enough at that point. Other than that the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle had super consistent performance in terms of both FPS and accuracy.
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416 V2 Materials: Fiberglass reenforced plastic and metal. Weight: 7 pounds (3180 grams). Total Length: 28 - 31.1 inches (710-790). Barrel: 10.2 inches (260mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, parts of the sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover, buffet tube and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles . You’ll find that most part work in the same manner as with the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Removable metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Fully adjustable rear stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416 V2 AEG Airsoft Rifle has a really nice form factor allowing for a full size rear adjustable stock which will make your shooting position a lot more comfortable while still allowing for a rather compact form factor overall. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416 V2 AEG Airsoft Rifle:
Type: AEG Airsoft Rifles Manufacturer:Umarex / VFC Model:HK416C V2 Materials: Fiberglass reenforced plastic and metal. Weight: 6.1 pounds (2780 grams). Total Length: 22.6 - 27.4 inches (573-696mm). Barrel: 8.3 inches (210mm) non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 320 round magazines. FPS: 366+ fps.
Trigger Pull: The trigger pull on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is similar to a light single action trigger as they are essentially an electrical on off switch. There is about a quarter inch of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle, but plan to make my Field Test Shooting Video shortly. So stay posted for that video coming out soon. I do expected Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle to perform well as it is a high quality and not so inexpensive AEG Airsoft Rifle.
Build Quality: The Build quality on the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle looks to be really good, there are lots of quality metal parts throughout this Airsoft Rifle including the top and bottom receiver, rails, sights, flash hider, magazine, charging handle, selector switch, magazine release, forward assist, dust cover and trigger. VFC (Vega Force Company) is the actual manufacturer of this product line and they are well know for making high quality Airsoft products.
Realism: The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is a 1 to 1 scale fully licensed replica of the real steel HK 416 compact CQB styled rifles but in an even more compact design I believe specifically only found in Airsoft versions as I was not able to find the exact same model on the H&K Website. That said most part work in the same manner as you would find on the real steel version including the Charging Handle, Forward Assist, Bolt Release, Magazine Release, Selector Switch and Pop-up sights.
Pros:
Full H&K Licensed via Umarex.
Made by VFC (Vega Force Company), well known for quality products.
Lots of metal parts where would find them on the real steel HK416.
Semi auto & full auto selectable.
No orange tip on Canada import version.
Comes with AR type compatible high capacity 320 round magazine.
Pop up metal sights are adjustable for windage.
Lots of rail attachment positions.
Easy access to hop-up system.
Quality internals - V2 metal gearbox and built in Mosfet.
Ultra compact adjustable CQB stock.
Cons:
Price is on the higher end.
No elevation adjustment on sights.
Limited to physical size/type of battery used.
Comments:
The Umarex VFC H&K AEG Airsoft product line is going to be on the higher end of the price spectrum for sure but you are getting a really quality product here fully H&K licensed. The Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle is perhaps one of my favorites as I like more simplistic and minimalist styles of guns and this one for sure fits into that category. Even though it is small in nature it is super solid and heavier then it looks for sure when you pick it up with all the metal parts making up its build quality. I look forward to seeing how well the Umarex VFC Heckler & Koch HK416C V2 AEG Airsoft Rifle performs in my upcoming Field Test Shooting Video.
My Vimeo Table Top Review for the Umarex VFC HK416C V2 AEG Airsoft Rifle:
In this video I show you four Premium AEG Airsoft Rifles made by VFC and distributed and H&K Licensed by Umarex. This is not a detailed review but rather I focus on the basic specification and show my reaction as I take my first look at all four Umarex H&K AEG Airsoft Rifles. I do show off some close up photos so you can get an idea on the finish and what some of the components look like.
For this Field Test Shooting Video I put the Specna Arms RRA SA-C10 Core and Specna Arms RRA SA-E10 Edge head to head to see just how they will compare in terms of FPS and Accuracy at least out to 30 feet. If you want to know more about each of these AEG Specna Arms Airsoft Rifles then checkout my Table Top Review where I show them up nice and close and also talk about their specifications and how they both compare to each other.
For my Chronograph test, I decided to go with .25 gram Airsoft BB’s, a little bit heavier than what was used for the claimed FPS of around 380 using the M120 spring which by the way is preinstalled in these guns for import into Canada. Both the Specna Arms RRA SA-C10 Core and E10 Edge shot pretty similar with the C10 Core averaging right around 300 FPS and the E10 Edge shooting a little bit faster with 318 FPS. Throw some lighter .20 gram Airsoft BB’s into the mix and these numbers would go up for sure. I was using the same 11.1 volt Li-Po battery for all of my testing in this video.
Next I placed a fresh paper target 30 feet downrange and placed 10 semi auto rounds into it using a seated and rested shooting position. Both Specna Arms AEG Airsoft Rifles shot about a 1 inch grouping. I did find with both of these Specna Arms rifles that when using the peep sight they shot too low and when using the top notch sight they shot too high at least at this distance. Of course the sights are fully adjustable so this can easily be taken care of and you can adjust the hop-up for even more elevation considerations. After my 10 shot semi auto test I placed both Specna Arms Airsoft rifles in Full Auto and let the paper have it! As expected the groupings did spread out a little bit but not all that much, perhaps opening up to around 3-4 inches.
After testing both the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles side by side you really can’t go wrong with either version as they performed very similarly on the Chronograph and on Target. If you can afford to pay the little bit more than I would go with an Edge Series Specna Arms product since you do get a lot of extras for the little bit more you pay. Well worth it!
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model: RRA SA-C10 / RRA SA-E10 Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: C10 4.9 pounds ( 2.2 kg) - E10 5.1 pounds (2.3 kg). Total Length: 21.7 - 25.2 inches (550 - 640mm). Barrel: 6.7 inch (170mm) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: Mid cap 120 round magazines. FPS: 375 - 390 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on both of the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles is similar to a light single action trigger as they are essentially an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is going to be, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles, but plan to very soon. They are next on my list for Filed Test Shooting Videos so stay posted for that video coming out soon. I do expect them to perform well and will be shooting both of these models side by side to see if there is any noticeable difference between the lower cost Core versus the slightly more premium Edge Specna Arms versions.
Build Quality: One thing I can say is no matter which version of the Specna Arms AEG Air Rifles you deicide to go with (either a Core or Edge Series), you are getting extremely good value for your money and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and slightly higher priced Edge Series. You will get upgrades in the Edge Series such as a an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, the New Orion Gearbox, deep laser engraved licensing and an additional magazine. All of this for the little bit more you pay for an Edge series Specna Arms AEG Airsoft rifle.
Realism: The Specna Arms RRA SA-C10 Core and E10 Edge AEG Airsoft Rifles are based on the AR15 or M16 platform of course in a very modern and PDW styled look. They look and feel the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Super affordable yet very high quality product for what you pay.
Two options to consider, both with good price points and value.
Quality components throughout both the Core and Edge series.
Rock River Arms Licensed with hologram on receiver.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Quick release fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options even on such short PDW styled AR’s.
Metal gearboxes with metal gears and mostly all metal parts inside.
Easy access to motor for any possible trouble shooting you may need to do.
Cons:
Popup sights are mostly plastic..
Need to hold back charging handle to access the hop-up wheel.
Comments:
Value for your money is what comes to mind when I think about the entire Specna Ams AEG Airsoft Riffle product line. And this goes for not only the lower priced Core Series but also the premium Edge Series. Both version are built supper tuff with quality components throughout. You are just getting upgrades you are probably going to do at some point in time with the Edge Series and of course more metal components when you spend about $100 more for a similar Edge version. I figure if you can muster up the extra cash then go with an Edge Specna Arms AEG Airsoft Rifle, that said, any of the Core models will be money well spent.
Make sure not also watch my previous Specna Arms YouTube Video where I introduce the product line, show you around several models and talk about the key differences between the Core and Edge versions.
My Vimeo Table Top Review for the Specna Arms RRA C10 Core & E10 Edge Airsoft Rifles:
We have a new line of Airsoft rifles from Specna Arms I am super happy to be introducing to the Replica Airguns Airsoft Community.
Specna Arms AEG Airsoft Rifles are extremely cost effective and offer value for what you pay that is amazing. In this YouTube Introduction Video I go over the main differences between the Core Series (lower priced) versus the Edge Series (mid priced) so that you can understand what the extra cost will get you when buying a Spenca Arms Edge Series AEG Airsoft Rifle over a Specna Arm Core Series AEG Airsoft Rifle.
I also show 12 different versions from the Specna Arms Core and Edge Series some with Rock River Arms licensing and some without.
Specna Arms Core Series
Price: Mid $200’s (CAD)
Materials: Fiberglass Reenforced Plastic & Metal
Mosfet System: No
Gear Box: Ver 2 Metal Fully Upgradeable
Spring System: ESA Quick Change - 2 Springs (380-310 fps)
