Entries in .50 cal,Revolver

KWC 357 2.5 Inch CO2 Airsoft Revolver Table Top Review

3 Comments

Type: Airsoft revolver.

Manufacturer:KWC.

Model:357.

Materials: Mostly metal with some plastic construction.

Weight: 2 pounds (900 grams).

Barrel: 2.25 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 6 rounds.

FPS: 360+.

Trigger Pull: The trigger pull on the KWC 357 2.5 Inch CO2 Airsoft Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357's. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy: This is yet to be determined but I did notice on the KWC Airsoft versions of their shell loading Airsoft Revolvers, that they do have a built in preset Hop-up by way of a small rubber bar that goes along the top of the barrel just inside the rear portion. This will create some backspin which will keep the Airsoft BB's trajectory more level but should also help them stay more accurate in general as compared to a plastic Airsoft BB that is not spinning but rather just floating through the air.

Build Quality: The KWC 357 2.5 Inch CO2 Airsoft Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 is noticeably more! The only real plastic or rubber I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable wear or sloppy workmanship.

Realism: The KWC 357 2.5 Inch CO2 Airsoft Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 Airsoft revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands that a real 357 magnum or even when shooting 38 special shells for that matter ;)

Available in the:Replica Airguns Store.

Pros:

  • Shell loading revolver adds to the realism!

  • Mostly all metal design.

  • Pretty all the parts work as they would in a similar real steel revolver of this type.

  • Good overall weight, Very dense because of the shorter barrel.

  • Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).

  • Fully adjustable rear sight for windage and elevation.

  • Well hidden CO2 Screw.

  • Recessed barrel.

  • Not much white writing on the gun.

  • Nice easy Trigger pull in both single and double action.

Cons:

  • Short 2.25 inch barrel will rob power but the Dan Wesson style long barrel Airsoft revolvers are know to be a bit hot for some Airsoft games so this may be a good thing.

  • Grips may be a bit large for people with small hands.

  • All black sights with no white dots are not great on dark backgrounds or low lighting.

Comments:

The KWC 357 2.5 Inch CO2 Airsoft Revolver is yet another addition to the increasing lineup of shell loading revolvers available today in both Steel BB and Airsoft versions. The 2.5 inch reviewed here is meant to be the compact version with its snub nosed barrel but I would have to say it is not a small gun at all coming in at 2 pounds and with rather large grips and a pretty large cylinder to pack around. But then again, that may be just what you are looking for? The shorter barrel will lower the fps a bit which may bring it back in line with the requirements of some Airsoft fields and the addition of the built in preset Hop-up, this pistol should shoot pretty well out at medium and even longer ranges.

My Vimeo Table Top Review for the KWC 357 2.5 Inch CO2 Airsoft Revolver:

Categories: 6mm, Airsoft, CO2, Comparison, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: 357, KWC

KWC 357 6 Inch Chrome CO2 BB Revolver Table Top Review

12 Comments

Type: BB air revolver.

Manufacturer:KWC.

Model:357.

Materials: Mostly metal with some plastic construction.

Weight: 2.75 pounds (1218 grams).

Barrel: 5.5 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 6 rounds.

FPS: 400fps.

Trigger Pull: The trigger pull on the KWC 357 6 Inch CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the KWC 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy:Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

Build Quality: The KWC 357 6 Inch CO2 BB Revolver being mostly metal has a very good build quality, perhaps even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the KWC 357 came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time...

Realism: The KWC 357 6 Inch CO2 BB Revolver overall is a close copy a the real steel 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.

Available in the:Replica Airguns Store.

Pros:

  • It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.

  • Mostly all metal design.

  • lots of detail, well made, Chrome looks nice, not sure if it will ear better than the black finish?

  • Good overall weight, heaviest out of all the shell loaders.

  • Should have good overall power, accuracy and shots per CO2 (based on Colt Python testing).

  • Fully adjustable sights for windage and elevation.

  • Well hidden CO2 Screw.

  • Recessed barrel.

  • Nice easy Trigger pull in both single and double action.

Cons:

  • Grips are a bit rough.

  • Grips may be a bit large for people with small hands.

  • Black rear sight may not be great on dark backgrounds or low lighting.

Comments:

The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The KWC 357 6 Inch CO2 BB Revolver like the Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic 357 magnum platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these, the Chrome finish is really eye catching and would make a great addition to your revolver collection for sure.

My Vimeo Table Top Review for the KWC 357 6 Inch CO2 BB Revolver:

 
Categories: 4.5mm / .177 cal, BB, CO2, Comparison, Pistol, Review, Revolver, YouTube Video Tags: 357, Colt Python 357, KWC

KWC 357 and ASG CZ 75 P-07 - CZ 75D Compact and Bersa BP9CC BB and Airsoft Update Video

1 Comment

Some more CO2 pistols I will be doing Table Top and Field Test video reviews for in the near future. Some of them I have already reviewed in different caliber versions, either 4.5mm Steel BB or 6mm Plastic Airsoft.

From KWC I show off two revolvers styled after the 357 and if you watched my Umarex Colt Python 357 Review then you will notice the similarities between these KWC made revolvers since they are all made by KWC. The Model 357 6 inch version is finished in Chrome and made to shoot 4.5mm Steel BB's while the KWC Model 357 2.5 inch shoots 6mm Plastic BB's and is in all black. At this time I do not have these KWC revolver listed in the Replica Airguns Canada Store but should have them listed fairly soon...

I also showcase three CO2 6mm Airsoft semi auto pistols from ASG that I have already reviewed in their 4.5mm Steel BB equivalents. The ASG CZ 75 P-07 Duty Non-blowback, the ASG CZ 75 D Compact Non-blowback and the ASG Bersa BP9CC Blowback.

Make sure to watch my quick Update Vimeo Preview Video for these fine CO2 pistols to see them up close and personal...

 
Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Comparison, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: 357, ASG, Bersa, CZ 75 P-07 Duty, CZ 75D, KWC

What is an Uncontrolled Firearm in Canada?

6 Comments

This Article and Video expresses my views and opinions on this matter and should not be taken as legal advice.

Main points covered:

  • Uncontrolled Firearms do not require a Firearms License within Canada to own and operate.

  • What is an Uncontrolled Airgun and Airsoft Gun?

  • What is an Uncontrolled Blank Gun / Starter Pistols?

  • What about Fully Automatic Airguns and Airsoft Guns?

  • What about Replica Guns?

NOTE: Controlled Firearms require a POL (Possession Only License) , PAL (Possession Acquisition License) or R-PAL (Restricted Possession Acquisition License) within Canada to own and operate. 

MEMORANDUM D19-13-2

Firearm – a barreled weapon from which any shot, bullet, or other projectile can be discharged and that is capable of causing serious bodily injury or death to a person, and includes any frame or receiver of such a barreled weapon and anything that can be adapted for use as a firearm.

“Uncontrolled”firearms are those devices that, although falling within the definition of a firearm in the Criminal Code, are exempt from specific legal requirements of the Firearms Act and its regulations, as well as from other legislative provisions. “Uncontrolled” firearms should not be subdivided into any of the non-restricted, restricted, or prohibited classes. The following types of firearms are deemed “uncontrolled”:

Flare, blank, rivet and industrial guns: Any device that is designed exclusively for signaling, for notifying of distress, or for firing blank cartridges or for firing stud cartridges, explosive-driven rivets or other industrial projectiles, provided that the importer intends to use it only for the purpose for which it is designed.

NOTE: (Toy guns and starter pistols do not generally qualify as firearms. However, some toy or model guns and starter pistols may be designed with very realistic mechanisms or appearances (e.g., color, size, scale, translucency) and resembling a real make and model of a firearm. In such cases, they may be considered replica firearms even if they are made of plastic, die cast zinc, or other material.)

Low muzzle velocity/energy guns: Any barreled weapon that is not designed or adapted to discharge projectiles at a muzzle velocity exceeding 152.4 meters per second (500 feet per second) and at a muzzle energy exceeding 5.7 Joules, or to discharge projectiles that are designed or adapted to attain a velocity exceeding 152.4 meters per second (500 feet per second) and an energy exceeding 5.7 Joules. Both thresholds of 152.4 mps and 5.7 Joules must be exceeded for the firearm to be considered “controlled”. This requirement exempts firearms that fire below the threshold velocity with a standard projectile, but exceed the threshold velocity when fired with a high-velocity projectile. 

Airsoft guns and certain types of paintball guns or markers may qualify as a replica firearm, if the muzzle velocity of the projectile does not cause serious bodily harm and their external features are clearly designed to resemble a specific and readily identifiable make and model of a firearm. To be considered a firearm, within the meaning of the Criminal Code, an airsoft gun must have a muzzle velocity in excess of 111.6 meters per second (366 feet per second).

NOTE: This memorandum used to state when using a .20 gram BB but does not specify this BB weight anymore?

NOTE: The term air gun is a colloquial term referring to BB or pellet guns. Such guns operate either as spring- powered, gas-powered, or electrically powered. If the muzzle velocity of the air gun is less than 152.4 mps (500 fps)/5.7 joules but still able to cause serious bodily injury to a person, it may be considered an “uncontrolled” firearm. Airsoft guns and certain types of paintball guns may qualify as a replica firearm (see paragraph 49 of this memorandum).

Replica firearms:

“Replica firearm” is defined as any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm.

For a device to be a replica firearm it must meet all three requirements:

  • (a) it cannot be a firearm, meaning it does not discharge a projectile with sufficient energy to cause serious bodily injury or death to a person. If the device is a firearm, then it cannot be a replica firearm (and vice versa);

  • (b) it must resemble exactly, or with near precision, a real existing firearm of an identifiable make and model. With respect to visual examination, note that the maximum observing distance is one at which the equivalent make and model of the firearm can be identified. This distance will vary from one firearm make to the next. For example: A Luger pistol has a very distinctive silhouette as compared to other makes and is therefore more readily identified from further away. The examination of the object is something more than casual, but less than detailed. The device does not need to be so close that markings are identifiable; and

  • (c) it cannot be designed or intended to exactly resemble, or to resemble with near precision, an antique firearm. 

RCMP Website "Air Guns"

1. Air guns that are "Controlled" Firearms for purposes of both the Firearms Act and the Criminal Code

These are air guns with both a high muzzle velocity (greater than 152.4 meters or 500 feet per second) and a high muzzle energy (greater than 5.7 joules or 4.2 foot-pounds). The "muzzle velocity" is the speed of a projectile at the instant it leaves the muzzle of a gun, normally expressed in meters per second or feet per second. The "muzzle energy" is the energy of a projectile at the instant it leaves the muzzle of a gun, expressed in joules or foot-pounds. Air guns need to meet both standards to be classified as "Controlled" firearms for purposes of the Firearms Act.

These high-powered air guns are subject to the same license and registration requirements as a conventional "Controlled" firearm. Owners and users are also required to store, transport, display and handle them safely in accordance with the regulations supporting the Firearms Act.

Usually, the manufacturer's specifications are used to determine what muzzle velocity and muzzle energy an air gun was designed to have. This information may be available in the user's manual or on the manufacturer's website. If the information is not available, individuals can call the Royal Canadian Mounted Police Canadian Firearms Program (CFP) at 1-800-731-4000 and ask to speak to a firearm technician to find out if the air gun is considered to be a firearm for purposes of the Firearms Act.

High-powered air rifles are generally classified as non-restricted firearms. However, the classification depends on the exact design of the air gun. Air rifles manufactured to resemble an assault rifle could be non-restricted, restricted or prohibited depending on the exact model imitated. High-powered air rifles would also be prohibited firearms if fully automatic or if they have a sawed-off barrel. They could also be restricted firearms if they have a folding stock that reduces the overall length to less than 660mm. 

Additional thought on this subject: Even though Uncontrolled Firearms are not governed by the same laws that apply to Controlled Firearms within the Firearms act and do not need to be handled or stored similar in the same way you are required to handle, transport and store a Controlled Firearm, we need to treat our Uncontrolled Airguns, Airsoft Guns and Blank guns with care and go over and above what is expected when had handle, transport and store them.

Categories: Airsoft, BB, Blank Gun, Full Auto, Gun Law, Gun Safety, Non Airguns, Paintball, Pellet, Pistol, Real Gun, Revolver, Rifle, YouTube Video Tags:

Large Umarex Order Just Arrived in Canada - Lots of Stock on Hand

No Comments

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Full Auto, Pellet, Pistol, Replica Airguns News, Revolver, Rifle, Semi Auto, Single Shot, Spring Piston Tags: Umarex

Swiss Arms 4 & 6 inch Full Metal Revolvers Added to the US Store

No Comments

We have just added the Swiss Arms 4 inch & 6 inch Full Metal Revolvers to the US Store, these are basically teh KWC made guns licensed through Cybergun with the Swiss Arms licensing so you can check out my Umarex Colt Python 357 since it too is the same base gun made by  KWC.

Here are the specs for these Shell loading 357 styled CO2 4.5mm BB Revolvers.

6 Inch Barrel Length Model

  • FPS: 410
  • Mag Capacity: 6 rounds
  • Power CO2
  • Length: 11.42 inches
  • Weight: 2.67 lbs
  • Full Metal, Rubberized Plastic, Textured Grips
  • Rotating Cylinder, Manual Safety, Working Ejector Rod
  • Single & Double Action
  • Includes: 1 Gun, 6 Realistic Shells, 1 Speed Loader

4 Inch Barrel Length Model

  • FPS: 344
  • Mag Capacity: 6 rounds
  • Power CO2
  • Length: 9.44 inches
  • Weight: 2.39 lbs
  • Full Metal, Rubberized Plastic, Textured Grips
  • Rotating Cylinder, Manual Safety, Working Ejector Rod
  • Single & Double Action
  • Includes: 1 Gun, 6 Realistic Shells, 1 Speed Loader
Categories: 4.5mm / .177 cal, BB, CO2, Pistol, Replica Airguns News, Revolver Tags: Cybergun, KWC, Swiss Arms

Umarex Colt Python 357 BB Revolver Field Test Shooting Review

2 Comments

First off, make sure to checkout my Table Top Review for the Umarex Colt Python 357 CO2 BB Revolver so you can get the specs and details on this fine shell loading BB pistol.

In this Field Test Shooting Video I do my traditional Chronograph test where I shoot a series of 4.5mm Steel BB's using a brand new CO2 cartridge to see what kind of real word Feet Per Second performance I can get out of the Umarex Colt Python. On this day I averages right around 390 fps which was very close to the claimed 360 fps form Umarex. The temperature was right around 24 Celsius or 75 Fahrenheit so it was neither cold or hot.

Moving on with the Accuracy Shooting Test, I set myself up 30 feet away using a semi-rested stance (Sand bag up front, standing in the back) I got one of my best ever 6 shot groups from the Umarex Colt 357, coming in at just under 1 inch. During my previous pretest, the Umarex Revolver did well but seemed to spread out a bit vertically, this may have been due to the plastic tips on the shells needing to break in for a more consistent BB fit.

The Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight than most comparable shell loading BB revolvers, a smother trigger and hammer mechanism and styling this revolver on the Classic Colt Python platform. If you're a revolver fan, make sure to grab one of these and if you're not a revolver fan, this pistol may just change your mind :)

 Buy the Umarex Colt Python 357 in Canada

Buy the Umarex Colt Python 357 in the US

Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Colt Python 357, Umarex

Umarex Colt Python 357 CO2 BB Revolver Table Top Review

2 Comments

Type: BB air revolver.

Manufacturer:UmarexUSA.

Model: Colt Python 357.

Materials: Mostly metal with some plastic construction.

Weight: 2.75 pounds (1218 grams).

Barrel: 5.5 inches, non-rifled.

Propulsion: 12 gram CO2.

Action: Revolver, single & double actions.

Ammunition Type: 4.5mm steel BB's.

Ammunition Capacity: 6 rounds.

FPS: 400fps.

Trigger Pull: The trigger pull on the Colt Python 357 CO2 BB Revolver is good in both single and double action, even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, most likely because the spring tension that pushes the inner barrel to make contact with the cylinder is noticeably lighter on the Umarex Colt Python 357. Even the hammer is smoother and has less wiggle, just a better trigger and hammer mechanism overall.

Accuracy: The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

Build Quality: The Umarex Colt Python 357 being mostly metal, you would expect it to have a decent build quality and I am happy to say it does, perhaps again even better than the Dan Wesson and S&W 327 TRR8 shell loading revolvers, even the weight of the Colt Python came in close to a half of a pound more! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable paint wear or sloppy workmanship.

Realism: The Colt Python 357 CO2 BB Revolver overall is a close copy of the real steel Colt Python 357. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that this pistol is super close to the original revolver it is based and licensed on. Agin being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands.

Available in the: Replica Airguns Store

Pros:

  • It's a revolver with actual shells! Give you the feeling of loading and shooting a real revolver.

  • Mostly all metal design.

  • lots of detail, well made, fit and finish is very good.

  • Good overall weight, heaviest out of all the shell loaders.

  • Good overall power, accuracy and shots per CO2.

  • Fully adjustable sights for windage and elevation.

  • Well hidden CO2 Screw.

  • Recessed barrel.

  • Nice easy Trigger pull in both single and double action.

Cons:

  • Grips are a bit rough.

  • All black sights not great on dark backgrounds.

  • FPS seemed to fluctuate a bit 

Comments:

The ASG Dan Wesson shell loading revolvers reintroduced me to the joy of loading and shooting a revolver which up until that point was not that realistic of an experience when using a BB or Pellet revolver. The Umarex Colt Python 357 has taken it up a notch by adding just a bit more overall weight, a smother trigger and hammer mechanism and styling this revolver on the Classic Colt Python platform. And all of this for even less than the cost of the original Dan Wesson shell loading series CO2 BB revolvers. If you're a revolver fan, make sure to grab one of these and if you're not a revolver fan, this pistol may just change your mind :)

My Vimeo Table Top Review for the Umarex Colt Python 357 CO2 BB Revolver:

 
Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: 357, Colt Python 357, Umarex

Umarex Walther PPS and Colt Python 357 CO2 BB Pistol Preview Video

No Comments

In this Vimeo Update Video Preview I show you around two brand new Umarex CO2 BB pistols, the Umarex Walther PPS and the Umarex Colt Python 357, both recently added to our online Replica Airguns Store.

The Umarex Walther PPS is a full licensed CO2 BB Blowback replica of the real steel super compact Walther PPS and it compares well to the ASG Bersa BP9CC that I reviewed earlier and by the way ended up being one of my favorite compact air pistols. That said I think the Umarex Walther PPS is the new king! It is even more compact yet has great fps for a super small CO2 pistol, shot very accurate even from 30 feet out and has more blowback recoil than the larger Bersa BP9CC!

Here are some of the specifications for the Walther PPS CO2 Blowback 4.5mm BB Pistol:

  • Velocity: 350 fps

  • Length: 6.4”

  • Barrel Length: 3”

  • Weight: 1.2lbs

  • Magazine Capacity: 18 Rounds

  • Power: 12 gram CO2

  • Ammo: 4.5mm Steel BB

  • Material: Metal and Plastic

  • Action: Blowback Single Action Only

Umarex added another shell loading revolver to their collection, the fully licensed Colt Python 357 and again this revolver uses CO2 and shoots 4.5mm Steel BB's that are preloaded into 6 included brass shells. Out of all the 4.5mm shell loading revolvers to date, I have to say the Colt Python 357 is the heaviest coming in at just under 3 pounds. The trigger hammer combination is also very smooth and it has a fully adjustable rear sight for windage and elevation.

Here are some of the specifications for the Colt Python 357 4.5mm BB Revolver:

  • Velocity: 400 fps

  • Length: 11.75”

  • Barrel Length: 5.5”

  • Weight: 2.75lbs

  • Magazine Capacity: 6 Rounds

  • Power: 12 gram CO2

  • Ammo: 4.5mm Steel BB

  • Material: Almost all Metal

  • Action: Single and Double Action

Watch my Vimeo Preview Video of the Umarex Walther PPS and Colt Python 357 BB Pistols:

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Colt Python 357, Umarex, Walther, Walther PPS

CO2 Versus Spring Versus Pump Airgun Comparison

7 Comments

In this Comparison Video I go through the benefits and shortcomings of CO2, Spring Piston and Pump Airguns. I focus mainly on Airguns but there is a bit of a crossover with Airsoft guns.

All three systems (CO2, Spring, Pump) create pressure that forces the ammunition with a high force out of the barrel. Similar to how gun powder is the source of energy for a bullet.

Here are some basic statements that best describe CO2, Spring Piston and Pump Airguns.

CO2 Airguns:

  • CO2 Airguns use the expansion of CO2 gas to create the pressure required for the ammo.

  • CO2 Airguns generally store enough CO2 for multiple shots per cartridge.

  • CO2 Airguns have a limit as to how much power they can produce since CO2 has a set vapor pressure of 850 psi, or about 56 bar at room temperature which is around 25 C or 77 F. CO2 Gas also requires a warm environment to expand so warmer temperature and longer barrels help with power.

  • Some CO2 guns can also use pressurized air tanks in place of CO2.

Spring Piston Airguns:

  • Spring Airguns use the release of a pre-cocked spring and plunger system to compress air to power the ammo.

  • Spring Piston Airguns require the cocking of the spring between each shot so they are single shot only.

  • Spring Airguns are limited to how much effort is humanly possible to cock the spring into position. If you make the spring to strong then not everyone will be able to use the Airgun effectively. Too week of a spring and the Airgun will lack power.

  • Spring Piston Airguns are known for having a fair amount of recoil and vibration when the spring moves both forward and backwards quickly inside the Airgun.

  • Spring Airguns can use either a mechanical spring or a gas spring.

Pump Airguns:

  • Pump Airguns (either Single or Multi-Pump) store air pressure in a chamber that when released, powers the ammo.

  • Most Pump Airguns require at least 1 or more pumps, often up to 10 pumps for each shot and you generally only get one shot per set of pumps. Not to be confused with PCP Airguns (Pre Charged Pneumatic) which have large pressure tanks that are recharged with a high volume of pressurized air that is capable of shooting multiple shots per charge.

  • Pump Airguns are also somewhat limited to how much effort is humanly possible since the higher the chamber pressure, the harder it will be to pump the Airgun. 

Misc Airguns:

  • Generally speaking both Spring and Multi-Pump Airguns have more potential power than a CO2 guns since CO2 has a set peek pressure limit.

  • Pump and CO2 Airguns are know to have very little recoil since the pressure is stored in a chamber and then released by a valve. No slapping back and forth of a large internal spring.

Pros:

CO2 Airguns:

  • CO2 Airguns allow for multiple shots per CO2 cartridge for more realistic action shooting.

  • CO2 Airguns do not require any human effort to charge the gun other than loading the CO2 and Ammo into the Airgun.

  • CO2 Airguns allow for true semi auto shooting ability. 

Spring Piston Airguns:

  • Spring Airguns have the potential for high velocity since the larger and stiffer the spring, the greater the output force.

  • Spring Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

  • Spring Airguns are mechanically very simple which makes them very reliable and less expensive to produce than other types of Airguns. 

Pump Airguns:

  • Pump Airguns have the potential for high velocity since more pumps equals greater output force, only limited by the users strength and the pressure rating of the Airgun.

  • Pump Airguns do not require anything other than your ammunition, typically either a Pellet or BB.

  • Pump Airguns have next to no recoil which makes them very easy to shoot and highly accurate.

Cons:

CO2 Airguns:

  • CO2 Airguns require the purchase and use of CO2 or they simple do not work.

  • CO2 Airguns are very susceptible to temperature changes, especially cold temperature since CO2 needs a warm environment in order to expand. Cool down effect also plays a role in power output.

  • CO2 Airguns have a maximum set amount of power output.

Spring Piston Airguns:

  • Spring Airguns require the pre-cocking of the spring for each shot.

  • Spring Airguns can take some getting used to since the spring recoil/vibration requires a very lose grip (Military Grip) to shoot accurately with them.

  • Spring Airguns should not be stored pre-cocked since this can damage the spring, less so with gas spring versions. 

Pump Airguns:

  • Pump Airguns require pre-pumping to pressurize the air chamber for each shot.

  • Pump Airguns, especially Multi-Pump Airguns take the most amount of human effort for each shot.

  • Pump Airguns need to stored with at least one pump in them or the seals can get damaged over time.

Categories: .22 cal, 4.5mm / .177 cal, BB, Break Barrel, CO2, Comparison, Multi-pump, PCP, Pellet, Pistol, Repeater, Revolver, Rifle, Semi Auto, Spring Piston Tags:

Blowback Versus Non-Blowback Airgun Comparison

1 Comment

In this Comparison video I go through the benefits and shortcomings of both Blowback and Non-Blowback Airguns. I focus mainly on Airguns but there is a definite crossover with Airsoft guns.

Here are some basic statements that best describe both Blowback and Non-Blowback Airguns.

Blowback Airguns:

  • Blowback Airguns usually have a movable slide that moves back and forth with each shot.

  • Sometimes the blowback operation is internal (Internal bolt) so there may not be an external moveable slide.

  • Some CO2 is used to move the slide rearwards in a Blowback Airgun.

  • The Blowback motion of the slide with some blowback airguns can also cock the hammer or internal striker allowing for true single action trigger pull. But not always!

  • Some Blowback airguns have the potential for full auto capabilities since they can have a true semi auto action.

  • There is some noticeable recoil from the Blowback action simulating the recoil of a real gun.

Non-Blowback Airguns:

  • Non-Blowback Airguns can have fixed or movable slides but they will not cycle back and forth with each shot.

  • Non-Blowback Airguns tend to have less working parts since no Blowback valves are required or even a moveable slide.

  • There are some Blowback and Non-Blowback Airguns that field strip similarly to their real steel counterparts but this is most commonly found in Blowback Airguns.

  • Non-Blowback Airguns require the shooter to cock the hammer for single action shooting or use a double action trigger pull for semi auto like performance.

Pros:

Blowback Airguns:

  • Blowback Action causes a noticeable recoil which makes the airgun feel more realistic.

  • Blowback Airguns in some cases have true semi auto action with true single action triggers which mimic the authenticity of the real steel versions of the guns they replicate much better making them better training tools.

  • Having some recoil makes blowback Airguns potentially better training tools.

  • Blowback Airguns look really cool when shooting them  and are great action prop guns.

Non-Blowback Airguns:

  • Non-Blowback Airguns tend to have less working parts so less to go wrong and more reliability.

  • Non-Blowback Airguns can be more accurate since the recoil from the blowback is not a factor.

  • Non-Blowback Airguns have more potential power and more shots per CO2 since no CO2 is robbed for the blowback operation.

Cons:

Blowback Airguns:

  • Blowback operation can rob some of the power and will also rob how many shots you get from the Airgun.

  • Blowback Airguns are effected even more by cold weather and the cool down effect.

  • The recoil from Blowback Airguns can effect accuracy for some shooters.

Non-Blowback Airguns:

  • Non-Blowback airguns are generally double action when shooting semi auto and so the trigger pull will be longer and heavier.

  • Non-Blowback Airguns do not replicate the recoil action of a real gun.

  • Non-Blowback Airguns do not look as cool to shoot and are not as good of an action prop gun.

Categories: .22 cal, 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Comparison, GBB, Pellet, Pistol, Revolver, Semi Auto, YouTube Video Tags:

Is an Airgun Good for Self Defense?

3 Comments

Is an Airgun Good for Self Defense? Another one of those questions I get asked fairly often that's a bit hard to answer in a few sentences... Not all of us have easy access to a 9mm pistol or even a rifle but many of us can get our hands on an airgun fairly easily and they look real enough, I guess that is one thing they have going for them.

But what if the mere sight of what looks like a gun does not scare an intruder off? If you where hoping that would be enough, you may just be out of luck and what if you just brought an Airgun to a "real" gun fight? You are going to be drastically "outgunned" pun intended and here's why. A 4.5mm Steel BB weighs about 5.1 grains and generally you are looking at about 2-3 foot pounds of energy from a CO2 BB gun. Even a .177 caliber lead pellet is only marginally heavier at around 7-8 grains and if you're really lucky you might just get 4 foot pounds of energy out of a CO2 pellet pistol.

So let's take a look at a fairly conservative "real pistol" rounds, the 9mm. The 9mm rounds come in different bullet weighs but you can get a 120 grain 9mm in a plus p ammo with as much as 400 foot pounds of energy and even with that much raw power, many people claim that a 9mm round does not always have enough stopping power to put down a person even when shot multiple times center mass. It just depends what vital organs or arteries you hit that determines if he gets lucky or you get lucky.

Your 5.1 grain 4.5mm Steel BB is not going to do anything if it hits any type of clothing and even if you find some flesh it's just going to piss off the intruder.

My suggestion is to consider a bat or a golf club or a really big knife or just about anything other than an airgun because if the sight of the airgun replica does not scare an intrude away then you are really buggered.

Keep in mind that you need to abide by any laws regarding the use of self defense in your areas. Even just physical force could be considered a crime and at the end of the day you are ultimately accountable for your actions.

Categories: .22 cal, 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Gun Law, Pellet, Pistol, Real Gun, Revolver, Semi Auto, YouTube Video Tags:

Which Airgun is the Best?

6 Comments

I finally answer the question... Which Airgun is the Best? There has to be a best airgun out there right? So let's cut to the chase and stop waisting everyones time and money buying the third Best Airgun or even the second best Airgun! Why would you even want anything other than the very best Airgun available to mankind!

I really hope you weren't one of the gullible ones that actually bought something other than the Best Airgun, well I guess you're going to have to watch my YouTube video to find out which Airgun is the Best Airgun of all time...

Categories: .22 cal, 4.5mm / .177 cal, BB, Blowback, CO2, Comparison, Multi-pump, Pellet, Pistol, Review, Revolver, Semi Auto, Spring Piston, YouTube Video Tags:

SHOT Show Vegas 2014 G&G Booth

3 Comments

We carry a lot of the G&G line and perhaps have as much in stock as you would find at the G& G booth ;) I did see a few items we do not have in stock so I will have to see what I can do about that. Some products that I hope to see added to our Canada Replica Airguns Store would for sure be the M1 Grand and our Canadian Military Colt C7A1/2.

Categories: 6mm, AEG, Airsoft, Airsoft News, Blowback, CO2, Full Auto, GBB, Pistol, Revolver, Rifle, Semi Auto Tags: Colt C7A1, G&G, M1 Grand, SHOT Show

SHOT Show Vegas 2014 ASG Booth

13 Comments

I also visited my friends at the ASG booth but for some reason I did not get a photo  of their booth? I do have some video walk through stuff I will show you in my YouTube Video coverage of this years Vegas SHOT Show. Most importantly I have lots of gun photos so let's take a look at them...

One of my favorite ASG pistols is the Bersa BP9CC, I have already reviewed it and I just really like how this gun looks and holds, ASG took it one step further this year by adding a two-tone silver version and I have to say it looks awesome in person, my photos do not do it justice at all :(

A new handgun to the ASG blowback pistol series is the CZ P-09 Duty Pellet pistol. Basically it shares similar mechanics to the Umarex PX4 and Gamo PT-85 using the double sided rotary pellet magazine with 8 shots located on each end of the stick magazine. The ASG CZ P-09 Duty features a metal slide, working hammer and safety.

Another pellets pistol that should be very familiar to most of you is the new .177 caliber pellet shooting Dan Wesson in 6 inch silver and 8 inch black versions. ASG added a rifled barrel and redesigned solid brass shells that hold pellets instead of 4.5mm Steel BB's. Expect to take a little bit longer to reload the pellets as unscrewing the tip of each shell is required to place a .177 caliber pellet in each bullet tip.

Of course ASG has tons of licensed pistols to choose from, many on both 4.5mm Steel BB and 6mm Plastic Airsoft!

One new rifle that stood out to me was the ASG CZ Scorpion EVO 3 A1 AEG Airsoft Rifle, the Scorpion features an intelligent AEG system that detects when there may be a potential feeding problem and also when the magazine is out of ammo.

Categories: 4.5mm / .177 cal, 6mm, AEG, Airgun News, Airsoft, Airsoft News, BB, Blowback, CO2, Full Auto, Pellet, Pistol, Revolver, Semi Auto Tags: ASG, Bersa, CZ P-09 Duty Pellet, CZ Scorpion EVO 3 A1, Dan Wesson Pellet, SHOT Show

Shot Show Vegas 2014 Umarex Booth

18 Comments

Umarex had a lot of new products this year so I thought I would start off showing you some of them. I will be following this post up with a full 2014 Vegas SHOT Show video once I finish posting some of my photos and comments on the show events.

Here is a photo of the main Umarex Booth.

I have always liked the 4.5mm BB version of the Umarex Makarov, Umarex now has the Makarov Ultra version that features blowback, a working slide catch and full size drop out magazine, looking forward to testing this one out!

Another kind of new addition to the 4.5mm Steel BB lineup is the Umarex Beretta Model 84FS. It has been available overseas but is now coming to North America. The Umarex Beretta Model 84FS also features blowback and a full size drop out magazine.

I'm not sure if we needed another rebranded version of the KWC 1911 Blowback BB pistol, but we got one anyways! Umarex now has their own version of what looks to similar to the KWC Tac A1 but with Colt licensing. 

Umarex also made up a very limited edition and very weathered looking blowback BB shooting 1911 based on the KWC design called the Colt 1911 WWII Commemorative. I am not sure how many where made but I know there are not a lot of them... Hope I can get my hands on one...

Umarex came out with Smith & Wesson 327 TRR8 last year and this year they have added a similar styled 4.5mm Steel BB shooting revolver with removable shells but in a licensed Colt Python 357 version.

Last but not least and going back many years, Umarex is bringing out another Legends Series 4.5mm BB pistol. The German Mauser C96, I'm not 100% sure if it's blowback or not but it does seem to have a working action, the main pistol is made out of Polymer but it does have a full size drop out magazine and seems to have good weight overall. Most of the parts work like the original Mauser C96 including the adjustable rear sight and safeties.

Categories: Airgun News, BB, Blowback, CO2, Pellet, Pistol, Revolver, Semi Auto Tags: Beretta Model 84FS, Colt 1911 WWII Commemorative, Colt Commander, Colt Python 357, Makarov Ultra, Mauser C96, SHOT Show, Umarex

ASG Dan Wesson 8 inch Revolver vs Umarex S&W 327 TRR8 Head to Head Shootout

No Comments

This post is really all about watching the YouTube video and seeing how these two similar CO2 4.5mm Steel BB revolvers compare to each other. I was working with a new Chronograph since again it was really dark outside and my old Chronograph does not like darkness. I did get some usable Chrony results with the new one but I did have to work for it ;)

Make sure to checkout my other posts for my Dan Wesson revolvers and also the Umarex S&W 327 TRR8.

Watch the video below to see the Dan Wesson 8 inch 4.5mm Steel BB Revolver go head to head against the Umarex S&W 327 TRR8 in both a test of the feet per second performance and accuracy shooting at 30 feet using a semi rested position.

Categories: 4.5mm / .177 cal, BB, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: ASG, Dan Wesson, S&W 327 TRR8, Umarex

Commonly Asked for Head to Head Gun Shootouts

No Comments

I get many question over on my Vimeo Channel, lots of times people asking me which gun is better and in most cases it really comes down to personal preference. But in some situations the comparisons are really close and to be honest it's even hard for me to decide which gun I think is better.

I get asked which one has higher fps, or is more accurate, or has harder blowback recoil... the list goes on. Without actually taking both gun outside and doing a head to head test using the same exact situations, I really can not honestly tell you! So that's exactly what I am going to do. Take some of the most commonly asked about gun comparisons and have a showdown.

Over the next while I will be making a total of five separate videos where I compare the following CO2 BB pistols head to head:

Make sure to come back and check out these upcoming head to head field test shooting videos!

Categories: 4.5mm / .177 cal, BB, Blowback, CO2, Comparison, Field Test, Full Auto, Pellet, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: ASG, Cybergun, Gamo, KWC, Umarex

My Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2013

6 Comments

So it's 2014 but I still needed to make my 2013 Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2013. It's become a tradition I guess you could say. No I do not show all the guns in my collection but I do cover most of my favorites and also some new guns I picked up in 2013.

Here's a peek but make sure to watch the YouTube video bellow where I go over all my top picks for 2013. You can also buy many of the guns I show in this YouTube video over in our Canada and US Replica Airguns Store!

2013 BB Pistols

2013 Pellet Pistols

2013 Airsoft Pistols

2013 Blank Pistols

2013 Rifles

Categories: .20 cal, .22 cal, .43 cal, 4.5mm / .177 cal, 6mm, 8mm, 9mm, Airsoft, BB, Blank Gun, Blowback, Bulk Air, CO2, Full Auto, GBB, Multi-pump, Paintball, Pellet, Pistol, Review, Revolver, Rifle, Semi Auto, Single Shot, Spring Piston, YouTube Video Tags:

ASG Dan Wesson 2.5 inch Gold - G&G G731 2.5 Airsoft Revolver Field Test Shooting Comparison

No Comments

Since both the Gold ASG Dan Wesson and the G&G G731 Airsoft Revolvers both have the 2.5 inch barrels on them and in many ways are very similar (at least mechanically), I thought I would not only do my Table Top Review but also my Field Test Shooting Review using both guns side by side so we can really get an idea of how they perform and compare.

As per usual, I test both pistols out on my Chronograph to see what kind of real world feet per second rating I get, since they are 6 shot Revolvers, I fired 6 single action rounds from each gun using .20 gram plastic Airsoft BB's and averaged out the string. Both guns shot a little bit over 400 fps with the Dan Wesson having just a bit of a higher fps over the G&G G731.

Next up was the accuracy test, I decided to setup at my 30 foot mark so that any accuracy differences would be more noticeable, again I shot 6 rounds from each gun while I used a semi rested position, (sand bag for a hand rest and standing in the back). This time I would have to give the slight edge to the G&G G731 as it seemed to shoot just a bit tighter grouping over my Dan Wesson Gold. Both guns shot pretty close to a 2 inch 6 shot group.

Both pistols have pretty decent single and double action triggers, there is a some noticeable friction when shooting in double action due to the way the barrel seals against the cylinder so you may want to shoot in single action when going for the most accurate of shooting.

When it comes to sight picture the Dan Wesson does have a fully adjustable rear sight but the G&G G731 gets the job done with it's simple yet effective grove sight which I kind of preferred with this style of short barreled revolver.

If you want more of that combat look with some Gold Bling than perhaps the Gold ASG Dan Wesson is the one for you? Perhaps you want something like the G&G G731, as compact and simple as it gets that you know you can count on as a backup ready sidearm. There isn't a bad choice here with either of these nice compact Airsoft Revolvers.

Categories: 6mm, Airsoft, CO2, Field Test, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: ASG, Dan Wesson, G&G, G731