Type: BB air revolver Manufacturer:Umarex. Model: Colt Python 375 Materials: Almost entirely all Metal. Weight: 2.75 pounds (1218 grams). Barrel: 5.5 inches, metal non-rifled. Propulsion: 12 gram CO2. Action: Revolver, single & double actions. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 6 round cylinder. FPS: 400.
Trigger Pull: The trigger pull on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is good in both single and double action, it’s nice that you have the shorter lighter single action trigger for slower more accurate shooting but you can also blast away in double action when you feel like it. The hammer on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is firm with not very much wiggle which some other revolvers in this category do have.
Accuracy: Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.
Build Quality: The Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver being mostly metal has a very good build quality and is on par with the Dan Wesson 715 shell loading revolver. It has a nice weigth adn balance to it and feels really good in the hand! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time compared to the black finishes fodun on most KWC made Airguns.
Realism: TheUmarex Colt Python 357 Magnum Chrome CO2 BB Revolver overall is a close copy a the real steel Colt Python 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that, this pistol is super close to the original Colt Python 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands and noise to be had.
Pros:
Shells loading revolver give you the feeling of loading and shooting a real revolver.
Mostly all metal design.
Lots of detail, well made, chrome looks nice, not sure if it will wear better than the black finish found on most KWC made pistols?
Good overall weight, almost 3 pounds.
Should have good overall power, accuracy and shots per CO2 (based on my previous Colt Python testing).
Fully adjustable sights.
Well hidden CO2 Screw.
Recessed barrel.
Nice Trigger pull in both single and double action.
Cons:
Grips are a bit rough and wood grain is only OK.
Grips may be a bit large for people with small hands.
Decent enough Colt Python 357 replica but the frame is a bit long between the cylinder and the hammer.
Comments:
It’s been a while since I reviewed a Shell Loading Airgun and this one is pretty much the same Airgun I have reviewed in the past in both the KWC and Umarex Distributed forms. It has been almost 6 years since I took a look at one on my table and it still hods up today. I plan on performing another Field Test Shooting Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver to see if I can replicate the same good results I did back in 2014 when I tested it out on my deck. If you’re looking for a shell loading revolver in the 357 design then for sure checkout the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver as an option.
My Vimeo Table Top Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver:
This is a combined Filed Test Shooting Video for the KWC 2022 NBB - 24/7 NBB - 24/7 Blowback CO2 BB Pistols. I already made an update video for these KWC Steel BB Pistols since they are slightly different version I have not covered in any video beforehand.
As per my typical Field Test Shooting Videos I first place 5 shots through my Chronograph to test out the real world fps of each gun. I then shoot 10 rounds on a paper target setup 30 feet away using a seated and rested shooting position. My ammo for this test was 5.1 grain zinc coated 4.5mm Steel BB’s for all airguns along within a brand new 12 gram CO2. The temperature in my indoor Sea Can Airgun Shooting Range was around 25 degrees Celsius (77 degrees Fahrenheit) for this test.
First up was the KWC 2022 NBB 4.5mm CO2 Steel BB Pistol with an average five shot fps of 347. The KWC 2022 NBB 4.5mm CO2 Steel BB Pistol was the least accurate of the three Airguns tested on this day getting about a 5-6 inch 10 shot grouping. I did notice when I went to edit the video that it did shoot a double shot on the first shot which lowered that first shot making the group a bit larger. This may have been as a result of pulling the trigger with the safety on right before which probably loaded a round into the barrel followed by the second pull loading a second BB into the barrel.
I then tested out the KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol which was by far the most powerful Airgun tested out of the three hitting a top fps of 452 with a five shot average of 420 fps! The KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol was also fairly accurate getting a nice 2 inch 10 shot grouping, slightly to the left and just under the bullseye. Nothing wrong with that!
The last KWC 4.5mm Steel BB pistol for the day was my KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol. The only only blowback single action shooter out of the bunch. As expected from a blowback CO2 Airgun the fps was lower averaging just under 300 fps (298 to be precise). The surprise of the day was the accuracy from the KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol was the best out of this test group getting really close to a 1 inch grouping very well centered just a tad to the right but with near perfect elevation.
Depending on what you are going for, all of these Airguns are great choices. If you want ultimate power perhaps go for the KWC 24/7 NBB 4.5mm CO2 Steel BB Pistol with its 450+ fps, if you want accuracy and realism then I would suggest the KWC 24/7 Blowback CO2 4.5mm Steel BB Pistol with its full blowback action and excellent accuracy.
You’ve seen them all before but have you seen them in this exact configuration? All the Airguns I show off in this video are made by KWC and generally come in either Steel BB and or Airsoft versions along with non-blowback and blowback versions. You can even find most of them redistributed by other companies like Umarex, Cybergun, Gletcher, Crosman and others even licensed in some cases.
The versions I am showing today I have not review yet in these exact configuration and all of them are the KWC made and distributed unlicensed versions, so nice and clean with virtually none of that ugly white lettering on them…
This Field Test Shooting Review for the Daisy Powerline 340 Spring BB Pistol is a lot different from most of my other shooting video reviews mainly because the Daisy Powerline 340 Spring BB Pistol is not a CO2 powered BB Pistol like pretty much every other 4.5mm Steel BB pistol I have ever tested. There are way more 6mm Airsoft spring pistols but when it comes to actual 4.5mm BB Pistols they are not very common. The Daisy Powerline 340 Spring BB Pistol is Kind of like the pistol version of the Daisy Red Ryder BB Rifle…
So let’s get right into the nitty gritty on how the Daisy Powerline 340 Spring BB Pistol performed in the Replica Airguns Indoor Sea Can Airgun Shooting Range. Starting off with the feet per second velocity for the Daisy Powerline 340 Spring BB Pistol Daisy claims around 240 fps. shooting about 8 shots through my chronographs with standard 5.1 grain 4.5,, steel BB’s I was able to get an average of just over 180 fps, the Daisy Powerline 340 Spring BB Pistol was super consistent shooting all shots between 181 and 189 fps.
I then proceeded to place 10 shots on my paper target setup 30 feet down range shooting from a rested portion with a sand bag up front supporting my hadbn’s and a stool to sit on in the back. The Daisy Powerline 340 Spring BB Pistol did shoot a bit low and to the left but all 10 shots grouped within 3 inches of each other, actually a bit better than I was expecting from a low cost BB Pistol like this. If I was shooting at a pop can and adjusted my aim point a bit I would have hit the can 10 out of 10 times which is about as good as you can ask for a plinker like this.
The best way I can describe the Daisy Powerline 340 Spring BB Pistol is the pistol equivalent of the Daisy Re Ryder in that it shoots 4.5mm Steel BB’s has a high capacity BB reservoir that holds lots of BB’s and you are required to cock the spring for each shot rather than use CO2 for power. This makes for an over low cost Airgun but like the Daisy Red Ryder it is a lot fo fun to shoot at the end of the day. The Daisy Powerline 340 Spring BB Pistol has a surprisingly good trigger and at the end of the day shot really consistently for me.
Type: BB Pistol. Manufacturer: Daisy Model:Powerline 340. Materials: Mostly metal construction. Weight: 1 Pound (454 grams). Barrel Length: 4-5 inches Total Length: 8.5 inches. Propulsion: Spring Action: Single action only. Ammunition Type: 4.5mm steel BB’s. Ammunition Capacity: 13/200 round magazine. Max FPS: 240 fps.
Trigger Pull: The Daisy Powerline 340 Spring BB Pistol has a single action only trigger. You will have to pull the slide back for each shot as this motion draws the spring back and also cocks the hammer. The trigger pull is fairly decent with about a quarter inch of take-up followed by a light predictable release. There will not be any action shooting since the trigger is not double action and the fact that the slide must be pulled back for each shot.
Accuracy: So far I have not made my Field Test Shooting Video for the Daisy Powerline 340 Spring BB Pistol but I did take it outside for some good old plinking to see how it would perform causally shooting in the yard. The Daisy Powerline 340 Spring BB Pistol shot a bit harder than I was expecting it to and I was even able to hit targets a good 50 or so feet away but did have to account for some trajectory arch. Accuracy seemed good in general without a lot of need to adjust my aim point as the sights seemed well centered out of the box which is good since they are not adjustable.
Build Quality: The build quality of the Daisy Powerline 340 Spring BB Pistol is nothing exciting as it is mostly plastic with a metal barrel and perhaps a few other internal metal parts. Being that the Daisy Powerline 340 Spring BB Pistol is mostly plastic it only weighs in at about a pound but feels good in the hand. Everything feels pretty solid on the airgun with good overall fit and finish.
Realism: In terms of realism the Daisy Powerline 340 Spring BB Pistol is a good replica of a Beretta 92 in terms of looks and size comparison. Other than the open slide area that exposes the inner barrel being shorter than a real steel Beretta (probably to accommodate the internal spring) the Daisy Powerline 340 Spring BB Pistol looks very close to a Beretta 92. Moving parts include the slide, hammer, magazine release and slide catch release which is actually the safety. Even the magazine is drop out and near full size. I also like that there are no perceivable screw holes which is usually the case with these types of low cost all plastic Airguns when they are basically two halves slapped and screwed together.
Pros:
Pretty decent replica of a Beretta 92 in general.
For an inexpensive Airgun it has a lot of working parts that make it more realistic.
Very low cost to buy and operate, no CO2 required (Under $40 in Canada Store right now).
Has a recessed barrel for added realism.
Single action only trigger is not overly long or heavy.
Lots of ammo stored in the internal hopper so no need for a lot reloading.
Safety actually looks like part of the gun built into the slide catch release.
Full size dropout magazine.
Weight and feel of gun are pretty good considering so much plastic.
Cons:
Not super high in the fps department.
Need to cock the slide for every shot so not going to be an action shooter.
Made in China.
Comments: The Daisy Powerline 340 Spring BB Pistol is one of those low cost yet kind of fun BB guns that as long as you don’t have super high expectations you will get a ton of fun out of for very little cost. At about $40 Canadian with a bit more for some 4.5mm steel BB’s you are ready to shoot all day long. I was a bit surprised at how decent of a little BB gun the Daisy Powerline 340 Spring BB Pistol is. It looks real enough, has a decent build quality to it, actually shoots pretty good with a nice trigger and for such a low cost airgun it has a lot going for it like lots of working parts and even a removable full size magazine that doubles as a 200 round hopper with 13 round internal magazine. I don’t think anyone will be disappointed buying the Daisy Powerline 340 Spring BB Pistol and it would make a perfect first BB gun for a younger person looking to get started out in the sport.
My Vimeo Table Top Review for the Daisy Powerline 340 Spring BB Pistol:
Type: BB Rifle. Manufacturer: Crosman. Model: R1 AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Blowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto
Trigger Pull: The trigger pull on the Crosman R1 CO2 Blowback BB Machine Gun is single action only since the charging handle must be cocked first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 CO2 Blowback BB Machine Gun when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Build Quality: The Crosman R1 CO2 Blowback BB Machine Gun is well made all around. Weighing in at 6 pounds without any add on accessories it feel solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 CO2 Blowback BB Machine Gun is about as real as you are going to get in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all love. Almost all the working parts work like they would on a real AR / M4 other than the forward assist which is moulded into the receiver.
Pros:
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included red dot sight and ability to add pop-up iron sights.
Lots of rails of mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No iron sights included.
Comments:
The Crosman R1 CO2 Blowback BB Machine Gun is really pretty much the same as the Crosman DPMS SBR and Crosman MPW with more or less Cosmetic changes. Like the Crosman MPW the Crosman R1 has an AR compatible Rear stock and pistol grip, the Crosman R1 CO2 Blowback BB Machine Gun is the only Crosman AR Full Auto CO2 BB Rifle that has the ability to change out the flash hider, you can even put a mock suppression or in it if you choose to. No matter which of the Crosman AR Full Auto CO2 BB Rifles you chooses to get they are mechanically every similar and share most of the same parts. I would say the Crosman R1 CO2 Blowback BB Machine Gun is the most customizable to date but they are all fantastic Air Rifles!
My Table Top Video of the Crosman R1 CO2 Blowback BB Machine Gun:
Here we are with yet another Crosman AR styled Full Auto Blowback CO2 BB Rifle and they just keep getting better, I say that lightly as even the first version the Crosman DPMS SBR still holds up to the 3 part lineup. It kind of has to since all three of them can be mixed and matched in terms of the uppers and lowers, magazines and I am sure most intern parts. Check out the Crosman DPMS SBR and the Crosman MPW for reference as I have made full table top and field test shooting videos for them already.
The purpose as always for my Field Test Shooting Videos is to find out how the airgun being reviewed performs in terms of velocity and accuracy, and if the ratings on paper end up being the same or close to the tested results. Crosman claims the Crosman R1 CO2 Blowback BB Machine Gun is capable of shooting 5.1 grain 4.5mm Steel BB’s at up to 430 fps. When I tested the Crosman R1 CO2 Blowback BB Machine Gun using my Chronograph averaging out 5 shots using a brand new set of CO2 cartridges I averaged 395 fps. Note the temperature in my Indoor Airgun Sea Can Shooting Range was about average at about 24 degrees Celsius or right around 75 degrees Fahrenheit. Comparatively I was able to get 405 fps from the Crosman DPMS SBR and around 385 fps with the Crosman MPW. Temperature may have beene slightly different on those testing days so that needs to be factored in.
Moving on to the accuracy portion of this Field Test Shooting Review for the Crosman R1 CO2 Blowback BB Machine Gun, I placed 10 semi auto shots on my paper target setup 30 feet downrange. I was using a rested and seated shooting position to help minimize human factor. I was able to get pretty much a 1 inch grouping with my 10 semi auto shots which was nit surprising as I have been able to get tight shot placement like this from the Crosman AR series before.
I then flipped the Crosman R1 CO2 Blowback BB Machine Gun semi auto selector switch to full auto and dumped the remaining 10 rounds into my paper target in full auto mode flowed by another full 25 round magazine again in full auto and the grouping only stretched out to about 2.5 -3 inches even with all the full auto vibrations and rocking around of the gun. Shot placement was a little bit high and to the left but this can easily be corrected using the red dot sight adjustments.
In summary the Crosman R1 CO2 Blowback BB Machine Gun performed a lot like the Crosman DPMS SBR and the Crosman MPW which makes since since all of them are virtually mechanically the same. In the end I think it really comes down to which of the Crosman AR type full auto BB rifles you like the look of since they areal very capable shooters. If you can’t decide then maybe get one of each :)
Watch my Preview Video where I take a quick look at the Sig Sauer MCX CO2 Pellet Rifle and Crosman R1 Full Auto BB Rifle. Full Table Top and Field Test Shooting Videos coming soon.
As always I like to test each gun out in the Replace Airguns Indoor Sea Can Airguns Range first placing 5 rounds through my Chronograph to find out the real world velocity of each test gun, then I shoot 10 rounds at a distance of 30 feet onto a paper target to see how tight of a grouping I can get shooting from a seated and rested position. When it come to full auto BB guns like the Umarex Legends M1A1 Blowback CO2 BB Machine Gun, I will usually switch up to full auto and dump the rest of the magazine to see if I can still sray on target with the remaining rounds.
For my Power or Velocity test I was using fairly new CO2, I had shot a full magazine a couple days before but the Umarex Legends M1A1 Blowback CO2 BB Machine Gun was all warmed up and ready to perform optimally. Umarex does state that it will shoot around 435 fps and with my 5 shot test I was able to confirm that with a 434 fps average. The temperature in the Sea Can was around 23 degrees Celsius or 73 degrees Fahrenheit.
For my accuracy test I setup a new paper target 30 feet downrange and proceeded to place 10 shots into it using the peep sights on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun. Other than one slight flyer my 10 round grouping was around 3/4 of an inch and just a tad low of the bullseye but pretty close. I then switched over to full auto fun mode and with the remaining BB’s I unloaded all 20 rounds in about a half a second, or at least it seemed like that! The Umarex Legends M1A1 Blowback CO2 BB Machine Gun even in full auto mode with the trigger matted till the gun ran out I was still able to get a 2 inch grouping!
I’m a big fan of the Umarex Legends Series BB Guns and the Umarex Legends M1A1 Blowback CO2 BB Machine Gun may be my favorite out of all of them to date. The Thompson M1A1 is just such a stand out Machine Gun we all know from the Mob shows. Not only does the Umarex Legends M1A1 Blowback CO2 BB Machine Gun look the part but it performs I would have to say so far the best when it comes to Full Auto Machine guns at least from Umarex. I do have to say that the Crosman CO2 BB AR Series does not disappoint. That said if you are looking for a more classic BB Machine Gun that performs as good as it looks then my advice is grab yourself one of the Umarex Legends M1A1 Blowback CO2 BB Machine Gun and add it to your collection.
My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.
I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.
Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.
Type: Air Rifle / Machine Gun. Distributer: Umarex Model:Legends M1A1. Materials: Mostly Metal build. Weight: 7.75 pounds (3.5 kilograms) Barrel: 12 inches - smooth bore steel. Propulsion: 2x12 gram CO2. Action: Internal BoltBlowback single action. Ammunition Type: 4.5mm Steel BB's. Ammunition Capacity: 30 round full size drop out magazine. Max FPS: 435.
Trigger Pull: The trigger pull on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun is single action only so you will need to charge the bolt for the first shot just like you would on the real steel Thompson M1A1, after that the blowback operation will charge the bolt which allows for semi and full auto shooting. Trigger pull is not very long or heavy.
Build Quality: The Umarex Legends M1A1 Blowback CO2 BB Machine Gun is pretty much all metal other than the stock and pistol grip. Pretty much everything that is black is going to be metal on this CO2 airgun. It weighs in at a hefty 7.75 pounds which is lighter than the real steel version by about 2 pounds but keep in mind the simulated plastic wood grips are a much lighter than real wood would be. Overall the fit and finish is really good, mechanical parts work well and seem to be well machined..
Realism: The Umarex Legends M1A1 Blowback CO2 BB Machine Gun is a 1 to 1 replica of the real steel World War II Thompson M1A1 Machine Gun and is very authentic looking with similar operation. Even the magazine holds 30 rounds just like the real steel Thompson M1A1. The blowback operation will give you a little bit of that shoulder tap but of course nothing like a 45 caliber M1A1. As expected in todays Replica Airguns the barrel is recessed to give it a larger opening and the CO2 screw is hidden well enough. I would like to see at least a real wood kit for the Umarex Legends M1A1 Blowback CO2 BB Machine Gun which would not lonely look even better but also increase the overall weight closer to the 10 pound real steel weight.
Yet another Classic Legends Replica Airgun from Umarex, maybe one of the best to date.
Mostly all metal design with good overall weight.
Semi and Full auto select-ability.
Dual CO2 design for increased shots and less cool down effect.
High capacity 30 round full size drop out metal magazine.
Umarex went with less rounds to get away from the double stay configuration of the 50 round Legends MP40 which was not always dependable.
Great looking replica of the real steel M1A1 in looks, operation and feel.
Internal bolt blowback will give a bit of recoil feedback feel.
Simulated wood looks very realistic.
Recessed barrel for added realism.
Cons:
Real wood hardware would have been cine and added it of additional weight. Maybe Umarex will offer this down the road?
Price is getting up there a bit but still worth it if you are an M1A1 fan, imagine what a real one would cost?
Going to eat up CO2 quickly in full auto mode but you can always switch over to semi auto.
Comments: Another great Legends product from Umarex, maybe even the best one so far. The only issues I had with the Umarex Legends MP40 was the double stack magazine feeding dependability with the 50 round double stack magazine not always feeding consistently. Umarex went back to a less aggressive closer to a single stack magazine on the Umarex Legends M1A1 Blowback CO2 BB Machine Gun which has a fewer rods but is expected to feed more consistently. I am looking forward to getting out and actually shooting the Umarex Legends M1A1 Blowback CO2 BB Machine Gun when I make my Field Test Shooting video. My advice right now with uncertainties about if and when we will get new inventory is buy now if you are in a position to as I am not sure how long they will last and when we will be able to get more stock.
My Vimeo Table Top Review of the Umarex Legends M1A1 Blowback CO2 BB Machine Gun:
I want to thank Drew from Tippmann Armory/Air Ordnance for sending me this unit for review. I have been wanting to get my hands one of these Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Guns for several years now and super glad I happened finally :) I really don’t think there is any airgun out there like it. I am really hoping that we will be able to have this one in both our Canada and US Online Replica Airguns Stores.
So what exactly is the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun? It’s a PCP powered semi/full auto .22 caliber pellet firing Airgun and it is available in a Canada legal version that shoots just under 500 fps allowing it to be classified here in Canada as an unregulated Firearm. Unregulated Firearms do not require a license or registration and do not have to abide by the same rules that regulated firearms have to such as full auto limitations, magazine capacities and size limitations. So in other words if you want a full auto .22 caliber Machine gun here in Canada this is going to be your only option at least for now.
Some other cool features about the Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun is the trigger setup, pull it light and quick and you get a single shot, pull and hold using medium force and you get full auto but not at a super high rate of fire. Press and hold the trigger down hard and you get full auto with a much faster rate of fire so you control the rate of fire by how hard you press the trigger down. Air-Ordnance SMG 22 .22 Caliber Full Auto Pellet Machine Gun also has an adjustment to set the maximum rate of full auto fire.
I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.
For now here are some of the key points I want to get out to everyone:
Mission: Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack. What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.
Modular
One base allows interchange of faceplates for different target configurations
One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles
Portable
Mount it on a shelf indoors
Mount it on a sawhorse outdoors
Carry it in a backpack or duffle bag- its 10 pounds
Rugged
Solid steel design
Faceplates from 10 gauge to ¼ inch thick
3-Dimensional
Faceplate is offset from paddles
Clipping the aperture does not guarantee a score
Intentions of target configurations
Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull)
1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper
AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.
WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures
10-15- Inspired by customer request, uses 10mm and 15mm apertures. High-Precision shooting.
The Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is one that you are really going to want to take outside and set targets up around 50-60 feet await make it a little more challenging adn I do plan on getting outside with the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle in a bit once the weather gets a bit nicer and have some fun shooting at longer ranges. For now I wanted to at least get out my Indoor Field Test Shooting Video where I can Chronograph the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle and also see what it can do shooting at 30 feet out.
Sig claims the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle to shoot .22 caliber lead pellets at up to 700 fps with a power output of 12 foot pounds. Using 14.5 grain lead pellets I placed 6 rounds though my Chronograph and averaged 585 fps with the fastest shoot hitting 611 fps. Keep in mind there are much lighter lead pellets out there and when it comes to alloy pellets they drop in weight even more so hitting 700 fps with a light grain lead or alloy pellet is very realistic. What about Sigs claimed 12 foot pounds of energy? I did the math and using a 14.5 grain pellet with a maximum velocity of 611 fps, these numbers produce just a hair over 12 foot pounds! Mission accomplished :)
What about accuracy, I have seen a few claims online that the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is not the most accurate Pellet rifle out there and you know what I don’t think that was the absolute intension when Sig thought this one up. After all it is a semi auto high capacity Airgun replica, not a target rifle. I still like to find things out for myself so of course I performed my accuracy test for the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle shooting 10 rounds into a fresh paper target from 30 feet back using a seated and rested shooting position. For this test I was using a red dot scope with a 3x magnifier on it. My first 10 rounds did OK producing just over a 1 inch grouping, not super great but most of the rods (8 of them) all struck the target within about 3/4 of an inch.
At this point decided to empty the rest of the magazine so about 15 rounds on the same target to see if the grouping stayed the same or maybe even speed out a bit. I was a bit surprised to find that my second 15 shot grouping all stayed within the higher 10 shot group again producing about a 3/4 inch grouping with just those two first test outliers? Maybe it was me, maybe it was the pellets, maybe it was the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle? The good news is you have 30 rounds to hit your target so even if a couple of them stray a bit you still got 28 left to get the job done.
The Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is one of the coolest Air Rifles I have tested and now own, not only is it a great Replica Airgun but it also performs well and can be used for plinking or small pest control. All at even a fraction of the cost of shooting 22LR rounds and that’s not even that expensive compared to 9mm and larger ammo. Let’s hope Sig Sauer makes a detuned Canada version so we can offer it up in our Canada Replica Airguns Store and if you live in the US then checkout the US Store for Sig Sauer buying options.
Type: Pellet Rifle. Manufacturer: Sig Sauer ASP Model: Sig Sauer MCX Virtus PCP Materials: Metal and Nylon Fiber build. Weight: 7.5 Pounds (3.4 kg). Barrel: 17.5 inch steel rifled. Propulsion: PCP comes with an 3000 PSI 1100 PSI regulated (206 BAR) tank 213 cc. Action: Semi auto with internal blowback. Single stage trigger single action trigger. Ammunition Type: .22 caliber pellets. Ammunition Capacity: 30 rounds belt fed. FPS: Claimed up to 700 fps with 12 foot pounds of energy.
Trigger Pull: The trigger pull on the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is actually pretty light and smooth when you consider the first part of the trigger pull is used to advance the belt fed 30 round magazine. I was expecting more added friction from the belt but this does not seem to be the case. There is some internal blowback action going on but it is only used to cock the internal bolt/striker which does lesson the overall amount of trigger pull required. The trigger pull is fairly short considering all that is going on and it's not overly heavy so quick and predictable action shooting is more than possible with the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle.
Accuracy: So far I have not done my official Field Test Shooting Video for the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle but I did have the chance to put some rounds down range inside my 40 foot Sea Can and I have to say it shoots really hard, even rocking my metal 22LR Metal Target Trap that I was knocking the cardboard and targets right off of . Sig Sauer claims up to 700 feet per second I have no reason not to believe this. In terms of accuracy, I’m not sure just yet what to think since all I did was shoot standing up unrested just to get some basic sighting adjustments in with my optic sights. We will see how the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle performs when I make my actual Filed Test Shooting Video for it!
Build Quality: The build quality for Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is very good, you can tell Sig Sauer had a lot of hands on in the design and production of this Pellet Shooting Air Rifle! The materials used and fit and finish are top notch and the mechanical function again is really good. I am kind of amazed at how well Sigs belt fed magazine design works in terms of feeding and operation. So far I have not experienced any pellet feeding problems or malfunction of any kind.
Realism: The Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is a 1 to 1 replica of the real steel Sig Sauer Virtus Patrol model and looks absolutely the part other than the noticeable PCP tank where a standard stock would normally be. What are you going to do since you really can’t hide even a small PCP tank inside a But Stock? This is just something you will have to overlook in order to get the consistency and power from PCP over CO2 based Airguns. Everything else about the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle is pretty much bang on in terms of realism including a fully working ambidextrous selector, magazine release and drop out magazine, charging handle and pop up sights.
Pros:
My new best semi auto pellet rifle replica I have seen and shot to date.
Excellent replica of the real steel Sig Sauer MCX Virtus (Patrol) with the exception of the PCP tank.
Awesome build quality, lots of metal parts and the nylon parts are true to form and very solid.
700 fps and 12 foot pound of energy makes it powerful enough for small pest control.
30 round full size belt fed magazine has super high capacity and works flawlessly.
Full PCP Tank will deliver up to 150 shots.
Trigger feels good, not too long or to heavy and very consistent feel on every shot.
Pop up front and rear sights adjustable for windage and elevation.
Lots of possible rail options with add on M-Lok hardware
Cons:
Will require a PAL Firearms License in Canada but is considered a Iong gun so not restricted or requiring registration.
Internal blowback action does not advance the belt fed magazine but does cock the internal bolt/striker making trigger pull lighter.
Pumping up the 213 cc 3000 PSI tank is a workout for sure but does get you 150 consistent shots..
The PCP tank is a giveaway when it comes to realism but with the tradeoff of more shot power and consistency.
Comments:
Prior to the release of the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle the Sig Sauer MPX .177 Caliber CO2 Powered Pellet Rifle was my favorite pellet based replica rifle since there really was nothing like it out there with a drop out belt fed high capacity magazine. Now with the release of the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle I have a new favorite Action Shooting Replica Pellet Rifle and with its additional velocity and power it can even double as a small pest control Airgun. For this reason I’ve set my Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle up with a traditional red dot for close range vermin termination but I’ve also added a 3x magnifier for when those pesky critters think they can outsmart me by keeping their distance. Not so! It’s too bad our Canada gun laws make it so difficult to have an Airgun like the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle if you are not a PAL owner, let’s hope Sig Sauer makes a slightly detuned version for the rest of the Canadian Market at some point.
My Table Top Review of the Sig Sauer MCX Virtus PCP .22 Caliber Pellet Rifle:
I have two new products from Sig Sauer Airgun devision to share with everyone here on the channel. They are both really different but I really like them both. Before I get into it I want to thank Sig Sauer for sending me both of these Airguns.
First up is the Sig Sauer MCX Virtus .22 Caliber PCP Air Rifle I showed y at SHOT Show this year. Well now it’s shipping and I have one :) At this time the only version of the Sig Sauer MCX Virtus .22 Caliber PCP Air Rifle is the 700 fps 12 not popguns version. This version is legal in Canada but you will need an unrestricted Firearms License since it falls under the definition of a non-centered fired long gun in the Canadian Firearms Act. Perhaps Sig Sauer will come out with a detuned version under 500 fps?
The Sig Sauer MCX Virtus .22 Caliber PCP Air Rifle uses a 13CI-3000PSI tank situated at the rear of the gun as part of the butt stock. You will need some sort of a pump or scuba pressurization system to refill the PCP tank which will get you up to 150 to 200 shots per fill up. The belt fed magazine holds 30 rounds which you can fire as fast as you can pull the semi auto trigger. By the way the trigger pull indexes the belt magazine while the PCP air pressure works the bolt allowing for a fairly smooth trigger pull. You will need to charge the Sig Sauer MCX Virtus .22 Caliber PCP Air Rifle before you start shooting.
The Sig Sauer MCX Virtus .22 Caliber PCP Air Rifle weighs in at 7.5 pounds, has a 17.5 inch barrel and a total length of 37.5 inches.
Unfortunately the microphone system I was using for some reason did not record the Lapel Microphones we where record the audio with for this ASG SHOT Show 2020 Interview Video. The Camera we where recording video with did record audio but as there is so much back ground noise going on at large show like this, the audio is far from good. That all said try do you your best to listen to what we are discussing. There are sections where the audio is fairly distinguishable and sections in the video that are not due the proximity of the camera.
Bob from ASG and I go over serval products for ASG at SHOT Show 2020 this year. We first take a look at the new ASG Shadow 2 CO2 Blowback BB Pistol. One interesting fact about the new ASG Shadow 2 is that it has an internal Hop-up system that help BB’s travel further out for longer range shooting. The ASG Shadow 2 also has a fully adjustable rear sight making this Blowback CO2 BB Airgun a potentially pretty decent target pistol.
Another new product from ASG we focused on is the Airsoft ASG B&T Universal Service Weapon designed for first responder situations. The ASG B&T USW has an extended rear frame allowing for a non-recipricating red dot sight placement. The ASG B&T Universal Service Weapon has a built in folding stock and you can trick it out with all kinds of add ons to make it your own.
Near the end of the video we took a look at some new ICS Airsoft offerings from ASG.
This isn’t a SHOT Show 2020 Interview but most certainly worth reporting on. While walking around SHOT Show I ventured into the Chiappa Booth as I own a .22 caliber 1911 styled pistol from them and they do have some interesting products to take a look at.
Then I saw a red tip on one of their Chiappa Rhino Revolvers which caught my eye since I was not aware that Chiappa was making an Airgun version of their Rhino. Well as it turns out they are hoping to be shipping both an Airsoft version and Steel BB version around spring time and from what I can tell there will be two finishes, a kind of Gold Satin finish and also a Back finish version. As is with a lot of revolvers these days they will be shell loading which will help them look the part of a real steel Chiappa Rhino Revolver.
Looking forward to getting my hands on one when they come out in Spring this year!
In this SHOT Show Las Vegas 2020 Interview Video Scott takes us through a range of new products from Air Venturi.
Scott and I talk about the Air Venturi TR5 and how it came about to fill the hole the Baikal MP-61 left behind. We also talk a look at some new Air Rifles, a pumper called the Butterfly with a super cool linkage based system that makes pumping a lot easier. A PCP side lever cocking Air Rifle that I’m not even sure has a name yet but will be available in .177 .22 and .25 caliber pellet for around $299 US.
The only Air Venturi replica we looked at is a new Springfield Armory under lever Spring Piston Air rifle modeled after the M1A. Last up Scott went showed us how the Bada Bang targeting system is shaping up and looks to be almost ready for production.
