This may be a bit controversial for some people who don't like the thought of using an gun for hunting or extermination of unwanted pests. But weather or not it is accepted by all, it is a practice that many people still embrace including myself when done in a humane way.

Let's start off by addressing this topic by asking some questions and filling in some of the answers. Keep in mind I go into much more detail in my Vimeo video below.

What is the reason that you need to Shoot or Hunt an Animal?

Are you shooting an animal out of need or just for fun, sure there is a thrill in the sport of hunting but after taking down your prey, the animal should not be killed in vain as the meat should be eaten. There are also times when pesky critters get into your gardens, tree farms, feeding stations garbages and who knows what else? I personally think shooting an animal that has not done you any harm or that you don't plan on eating is not ethical. So question your motives wisely?

Can you use an Airgun for Hunting and or Pest Control?

The short answer is yes! As long as you choose the correct Airgun for the job, one that has enough power and accuracy to get the job done in a humane manner. Using an underpowered or inaccurate gun of any type for the chosen target will lead to the animal being wounded and possibly getting away to suffer unnecessarily.

What about Pistols versus Rifles?

Given the choice, a rifle will always be your best bet, rifles tend to be more accurate since they are more stable to hold and the fact that the sights are further apart which improves the guns accuracy. Most rifles also allow for enhanced sighting systems like red dots or magnified scopes for even further accuracy improvements. There are some pistols made specifically for hunting and target shooting that can be accurate but I would limit their use to shorter ranges.

What about Pellet guns versus BB guns?

BB guns in general are not meant for hunting or pest control, and in most cases they are underpowered and not as accurate as their pellet shooting counterparts, especially out at longer ranges where most pests keep their distances to. If you plan on doing some hunting and or pest control, please invest in an adequate pellet rifle to get the job done humanly.

What type of Ammo is best for Hunting and Pest Control?

There are lots of types of pellets available, pointed, rounded, flat, hollow-point and even pellets that have nylon tips. At the end of the day, use the pellet that is the most accurate in your Airgun because shot placement will win over pellet shape any day of the week. The reality is that as long as that pellet hits the target with adequate velocity, it doesn't matter what shape it is, it's more than likely going to pass right through the animal.

What is the lowest FPS that I can use?

I would rather ask the question, what is the highest fps I can get away with since more fps will give you more margin for error, since it will have a flatter trajectory and will do more damage even if your shot is off a bit. An experienced shooter could make a kill shot on a small pest even with a 400 fps airgun but the shot would have to be perfect and the range would have to be close. Of course when shooting larger game, you will need larger caliber pellets with higher velocities. Also when using a high velocity airgun you need to consider what is beyond your target, if you miss, where is that pellet or bullet going to end up? You need to make sure you do not injure anyone by mistake as pellets/bullets can travel a long distance.

How large of an Animal can an Airguns Kill?

This is really dependent on the Airgun being used, Airguns come in many different calibers, from .177 right up to .50 caliber, some PCP Airguns can even take down a deer! You need to do your research and make sure the Airgun you choose has both the power and accuracy you need for the intend prey.

Where can I use an Airgun for Hunting and or Pest Control?

This is a question you need to ask your local authorities as laws and hunting regulations are different just about everywhere. Even shooting pests on your property may require a permit so be careful to obey your local laws.

In many of my reviews I show the loading process of each gun but sometimes I either skim over this part or assume most people already know how to load an Air Pistol and skip it entirely. Well as it turns out not everybody does know how to load up an Airgun or they are unclear on certain areas, like do you actually need the CO2 and how long can you leave CO2 in an airgun?

So I made a video specifically to cover how to load CO2, BB's and/or Pellets into your Air Pistol.

Now even though this video is targeted at 4.5mm Steel BB and Lead Pellet Pistols, there is a crossover with 6mm Airsoft Pistols so this video may also help an Airsoft shooter.

Our Family Bearded Dragon (Dijon) was looking rather sad and lonely today so I figured he could hang out while I made the video, he really doesn't do much of anything most of the time so why not give him a special appearance in one of the Replica Airguns Videos ;)

Two questions that come up over and over again and to be honest I just hate answering, mainly because both of these questions to me are kind of common sense questions. I feel if someone where to stop and actually think about teh question, the answers would become obvious.

That said, common sense has to be learned somewhere and not all of us are exposed to the same life experiences so here goes...

The two questions are:

• Will this Ammunition Work in my Gun?

• Can I Convert a Blank Gun to a Real Gun?

The answer for both of these question is actually the same! Use the ammo made for your gun and do not try to use anything other than the ammo that was made for your gun. Do not try to modify your gun to shoot anything other than the ammo that was made for it, if you do, you may be breaking the law and could land yourself in jail. If you can follow these rules then your ammo and gun will work as intended :)

So that's pretty much it in a nutshell, watch my YouTube video below as I show you examples of ammo types with visuals on exactly why you need to use the ammo made for your gun. I also talk about the dangers of attempting to modify a blank gun to shoot some sort of real bullet and why it is a very bad idea in so many ways to try and convert a blank gun into a real gun.

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the Canada Store

Buy the ROHM RG-88 9mm P.A.K. Blank Pistol in the US Store

This video should go "Hand in Hand" (pun intended) with my Best Two Handed Pistol Grip Tutorial Video that I did last year back in August. After that video I had several people ask me to talk about how to aim a gun. I guess if you have been shooting guns for a while you kind of take it all for granted but after teaching my kids the proper way to aim a gun at a target, this info is not naturally born into us ;)

This video demonstrate how and where to place your open gun sights on a target and also how you can compensate for a gun that may not be perfectly sighted in.

This is take 2 of my Modification to my F1 Chrony Chronograph. The purpose of this modification is to improve the low light FPS readings. In my first attempt I used LED Puck Lights but they where the kind that used flat panel LED's and they only had 4 panels per LED Puck which made each LED panel kind of bright. I did get OK with my first mod using LED Puck Lights but not as good as I would like to see.

So here we are with take 2 of F1 Chrony Chronograph LED Puck Light modification and this time around I am using standard bulb styled LED lights and to improve my chances of this working I went with and LED Puck that contained 24 LED bulb lights per puck, this way each light on it's own is a bit dimmer which I feel will give a more diffused lighting effect and hopeful consistent fps readings.

By the way I got these LED Puck Lights at my local dollar store for $2.50 each so not a very expensive modification, especially if they work.

Well... Watch the video and see how they perform...

This video was made to show you the results I got by mounting LED puck lights to the top of my F1 Chrony Chronograph defuser panel in order to improve the low light Feet Per Second readings when using 4.5mm Steel BB's.

I have been struggling with my F1 Chrony Chronograph during the fall and winter months as tit becomes overcast and dark where I live. There have been days where I have gone out to shoot my field test shooting video and not been able to get any Chronograph fps results which is very frustrating because much time and effort goes into the planning setup of each video.

I was given advice from several of my viewers to mount an LED puck style light on the back side of my Chronograph defuser panel and that this helps the Chronograph to read much better in low light situations.

I bought a multipack of the LED puck lights from my local Costco but they did not work as well as I expected them to as they had a panel style of LED rather than the bulb shaped LED which I think may diffuse the light a bit more. My next experiments will be done using LED Puck lights but with the bulb styled LED.

You can watch my video to see how my first attempt using an LED Puck light with my F1 Chrony Chronograph worked out.

So it's 2014 but I still needed to make my 2013 Airgun, Airsoft Gun and Blank Gun Collection Favorites for 2013. It's become a tradition I guess you could say. No I do not show all the guns in my collection but I do cover most of my favorites and also some new guns I picked up in 2013.

Here's a peek but make sure to watch the YouTube video bellow where I go over all my top picks for 2013. You can also buy many of the guns I show in this YouTube video over in our Canada and US Replica Airguns Store!

2013 BB Pistols

2013 Pellet Pistols

2013 Airsoft Pistols

2013 Blank Pistols

2013 Rifles

In this informative video I go over the very basics of gun "handling" safety. I don't talk about gun storage or even shooting of the gun, I strictly go over the main aspects of handling a gun in a safe manor.

These are the four main points I demonstrate in this video:

• Fingers off the trigger till you are ready to shoot.

• Keep the gun unloaded till you are ready to shoot it.

• Assume your gun is loaded at ALL times.

• Always point your gun in a safe direction.

Hopefully this video will prevent some unfortunate accidents, even airgun related accidents can cause serious injuries which in most cases can be prevented with the correct gun handling information.

I have made a

similar safety video

where I talk about general gun safety and speak more about storing and also some gun shooting safety tips.

You really need to watch my Vimeo Video to see how easy it is to take a brand new out of the box gun and give it that weathered, old, worn and used look that you would find in a classic vintage gun like a Luger P.08, Colt 45 1911 or any other classic firearm. Of course this is something you would do to a new gun that you want to make look old :)

This is a great way to take a gun that already has some wear marks on it and really give it the full worn in look, kind of an alternative to having to touch it up or refinish it.

Here is a hint... I use something magical to do it!

Buy the Umarex Luger P.08

One of the most important keys to shooting accurately is how you grip the gun! In this video I show you the two handed grip that I use and that I have learned from watching other accurate shooters. I also talk about arm and shoulder placement which is more important when shooting large caliber pistols but even when shooting airguns that have virtually no recoil you may as well practice the correct hand arm and shoulder placement for when and if you do start shooting heavy recoil guns.

The main hand grip points I talk about in this video are how to overlap your finders and thumbs and also the pressure used by each hand that will make all the difference down range when shooting at targets.

Watch my Vimeo Tutorial Video on the Best Two Handed Pistol Grip:

I wanted to cover some basic Airgun, Airsoft Gun, Blank Gun and Paintball Gun information on what do they all shoot, what makes them shoot and some other miscellaneous info thrown in along the way...

Your should also watch the video attached at the bottom of this post as it goes into a fair amount of detail.

Let's begin with the types of ammo used:

Airgun Ammo

• Airgun ammo for the most part is broken down into BBs and Pellets, the most standard size BB and Pellet is the 4.5mm or .177 caliber Steel BB and Lead Pellet. You can also get Pellets in other calibers and even other materials other than lead such as steel or aluminum, some can have plastic skirting around a metal interior.

• Pellets also come in a variety of caliber's like .177, .20. 22. 25 and even larger but then I would start considering them to be bullets as they will take on the shape of a bullet when they get into the larger sizes.

• Airgun Ammo is not be fired at people, it is primarily used for target and hunting small game.

• Airguns can use Spring Pistons, CO2, Compressed Air and Multi-pump propulsion systems.

Airsoft Gun Ammo

• Airsoft Guns for the most part shoot round 6mm (.22 caliber) plastic BBs which come in a variety of weights ranging from .12 grams up to .48 grams. There are larger Airsoft BBs such as 8mm and even larger.

• There are biodegradable and even tracer florescent Airsoft BBs available.

• Airsoft Ammo is traditionally used for Airsoft battles and can be fired at people using protective gear. Airsoft Ammo can also be used for target shooting.

• Airsoft Guns can use Spring Pistons, Spring Piston - AEG (Electric Motor) CO2, Gas (Green, Red, Propane) and Compressed Air propulsion systems.

Paintball Gun Ammo

• Paintball Guns or "Markers" have been historically used for the sport of Paintball but their whereabouts came from the need of ranchers and forestry workers to mark trees. Hence the name "Marker"

• Paintball ammo comes in a variety of sizes ranging with the most common being .43 and .68 caliber. They are generally made from a gelatin outer coating containing primarily polyethylene glycol, other non-toxic and water-soluble substances, and dye, they are usually biodegradable.

• Paintball Guns can also shoot a variety of Paintball Ammo that can be made out of Rubber, Plastic, Glass and they can also contain Powders and even Pepper for use in non lethal defense.

• Paintball Guns can generally use either CO2 or Compressed Air as their propellant.

Blank Gun Ammo

• Blank Guns are just like Real Guns but without the dangerous bullet at the end of the brass shell. Other than that they work exactly the same as a Real Gun!

• Blank Guns are used when a bullet is not required or even wanted. For instance... Gun safety, gun training, training animals to be around guns and/or loud noises, Props for Movies - Stage -  Film - TV, Collectors that do not want the red tape associated with owning a Real Gun or when owning a Real Gun is prohibited.

• Blank Guns can shoot a variety of sized ammo, most common are .22 caliber crimped, .380 crimped, 8mm P.A.K. and 9mm P.A.K.

• Blank Guns use gun powder as their means of operation.

Here are the most common forms of propulsion used in the guns we discussed earlier:

CO2

• CO2 is the most common propellant in Airguns (BB and Pellet), it is also used in Airsoft Guns and Paintball Guns.

• CO2 is a compressed gas which expands when released, it requires a warm environment to fully expand and tends to cool it's surroundings quickly when shot fast or in full automatic which can slow the velocity of the projectile and even freeze up the gun being used.

• The most common reusable CO2 cartridges are 12 and 88 gram but you can get larger CO2 tanks in a variety of sizes that can be refilled with CO2.

Gas

• Gas is used primarily in Airsoft Guns, I have not personally seen an Airgun that is made to use Gas other than CO2.

• Gas is similar to CO2 in that it is a compressed gas that expands when releases, it also cools down the gun it is being used in and requires a warm environment.

• Gas comes in a variety of names, Green Gas, Red Gas and Propane Gas. Green Gas contains Propane as it's base but has additives in it like silicone for lubrication .

• Red Gas is know to be a bit more powerful than Green Gas as it has Chlorodifluoromethane or HCFC-22, R22 or Freon 22 used in refrigeration which turns to a liquid under a slightly higher pressure giving you slightly higher fps.

• Many people use propane gas with an adapter that allows the mixture of silicone as propane is cheaper to buy.

Compressed Air (HPA)

• Compressed Air (HPA - High Pressure Air) is most commonly used in Airguns and Paintball Guns but some people use it for their Gas based Airsoft guns.

• The compressed air comes from high PSI tanks that can be purchased in a variety of sizes and contains compressed air at pressures up to 5000psi.

• These tanks are reusable and usually need to be refilled at a paintball or scuba shop, some people buy their own compressors or large scuba tanks for refilling purposes.

• Some Compressed Air (HPA) guns have their own built in tanks that can be filled with a compressor or even a manual pump.

• Compressed air does not cool down the gun it is being used in and is a great option for high output or fully automatic guns.

Multi-Pump Pneumatic

• Multi-Pump Pneumatic systems are most commonly used in Pellet and/or BB guns.

• Multi-Pump Pneumatic guns use the same principle as HPA - High Pressure Air guns in that they require pressurized air as the propellant. The main difference with Multi-Pump Pneumatic guns, is that you do all the work by pumping the gun between shots. Generally speaking you pump the gun 3-10 times, take a shot and repeat this process.

• Multi-Pump Pneumatic guns are not effected by air temperature and are great for target and small pest control.

Spring Piston

• Spring pistons are generally found in Pellet Rifles and Pistols but some Airsoft Guns also use a Spring Piston System and generally speaking Spring Piston Guns are single shot only or in other words, the Spring needs to be drawn back before each shot. Spring Piston Guns can have magazines that allow for quicker repeat shots.

• Spring Piston Guns come in many cocking configurations, Brake Barrel and Side lever to name a couple.

• The Spring can be a Mechanical Spring or a Gas Spring.

• Spring Piston Guns are not effected by temperature and are often used for small game hunting and target shooting.

Automatic Electric Guns (AEG)

• Automatic Electric Guns  are generally found in Airsoft Rifles but there are some Airsoft Pistols (AEP) that use this same system.

• Automatic Electric Guns use a similar system to a Spring Piston gun but have an electric motor that does all the work of drawing back the spring. You can even have fully automatic AEG guns.

• The power for the electric motor comes from removable batteries, so it is a combination a battery supplying the motor with the power to draw back the spring that creates a pillow of air that shoots the BB.

• AEG Airsoft Guns are great for situations when you require high capacity magazines with full auto capability. 

Gun Powder

• Gun powder is used in Blank Guns, in the same manor that it is used in a Real Gun, the charge from the Gun Powder supplies the force required to operate the blowback in most semi auto Blank Pistols, it also creates the sound of a live round along with the muzzle flash which makes Blank Guns great for training and as Props for Movies and Film.

• Because the kinetic energy from a blank gun is the same as a real gun, blank guns can be very dangerous when used in close proximity to an object, see my "Are Blank Guns Dangerous Video"!

Some other Gun Relevant Terminology:

Blowback

• Blowback operation is when some of the force of the propellant is used to move the slide backwards, which in most cases cocks the hammer for single action and can also pickup and chamber a round into the barrel.

• The slide spring supplies the energy for the return to the forward position of the slide.

• Blowback Guns do rob some power from the bullet force and in the case of CO2 or Gas Guns the also reduce the amount of shots per CO2 or Gas fill.

Revolver, Semi Automatic

• Revolver: Revolvers feed ammunition via the rotation of a cartridge-filled cylinder, in which each cartridge is contained in its own ignition chamber, and is sequentially brought into alignment with the weapon's barrel by a mechanism linked to the weapon's trigger (double-action) or its hammer (single-action)

• Semi Automatic:  semi-automatic pistols use the energy of one shot to reload the chamber for the next. Typically recoil energy from a fired round is mechanically harnessed. After a round is fired, the pistol will cycle, ejecting the spent casing and chambering a new round from the magazine, allowing another shot to take place immediately.

Single Shot, Repeater, Semi Automatic & Fully Automatic

• Single Shot: A Single Shot Gun needs to be reloaded each time it is shot.

• Repeater: Repeating action Guns are single barreled guns containing multiple rounds of ammunition. These rounds are loaded from a magazine by means of a manual or automatic mechanism, and the action that reloads the rifle also typically re-cocks the firing action. The term repeating rifle is most often applied to weapons in which the next cartridge is loaded by a manual action, as opposed to semi-automatic rifles, in which the force of one shot is used to load the next.

• Semi Automatic: A semi-automatic, or self-loading, firearm is a weapon that performs all steps necessary to prepare the weapon to fire again after firing.

• Fully Automatic: A Gun that uses either its recoil or a portion of the gas propelling the projectile to remove the spent cartridge (in the case of a gun-shell), fire again repeatedly, as long as the trigger is held down or until the magazine is exhausted. Automatic Guns are distinguished from semi-automatic Guns in their ability to fire more than one shot in succession once the trigger is pulled.

Single, Double Action, SA/DA

• Check out my post explaining Single and Double action!

• Single-Action (SA): trigger performs the single action of releasing the hammer or striker to discharge the firearm each time the trigger is pulled.

• Double-Action (DA): The trigger both cocks and releases the hammer or striker

• SA-DA:  A SA/DA firearm combines the features of both mechanisms. You can pull the trigger in Double Action when the hammer is down which cocks and releases the trigger or you can cock the hammer with your thumb and then release the trigger using Single Action to fire the weapon. 

Lever Action, Pump Action, Bolt Action

• Lever Action: In a classic lever-action firearm, rounds are individually loaded into a tubular magazine parallel to and below the barrel. A short bolt is held in place with an over center toggle action. Once closed, the over center action prevents opening solely by the force on the bolt when the weapon is fired. This toggle action is operated by a hand grip that forms part of the trigger guard. When operated, a spring in the tubular magazine pushes a fresh round into position. Returning the operating lever to the home position chambers the round and closes the breach.

• Pump Action: With a pump-action firearm, the action is operated by a movable fore-end that goes backwards and forwards to eject, extract, and chamber a round of ammunition. Pump-actions are usually associated with shotguns.

• Bolt Action: The bolt opens and closes the breech end of the barrel and contains the firing pin. The bolt is held in place with a lever that fits into a notch. Moving this lever out of the notch will release the restraint on the bolt, allowing it to be drawn back. An extractor removes the spent cartridge, which is then ejected through the lever slot. A spring at the bottom of the magazine pushes up the reserve rounds, positioning the topmost between the bolt and the chamber at the base of the barrel. Pushing the bolt lever forward chambers this round and pushing the lever into the notch locks the bolt and enables the trigger mechanism.

Magazine vs Clip

• Magazine: A magazine is an ammunition storage and feeding device within or attached to a repeating firearm. Magazines can be removable (detachable) or integral to the firearm. The magazine functions by moving the cartridges stored in the magazine into a position where they may be loaded into the chamber by the action of the firearm. The detachable magazine is often referred to as a clip, although this is technically inaccurate.

• Clip: A clip is a device that is used to store multiple rounds of ammunition together as a unit, ready for insertion into the magazine or cylinder of a firearm. This speeds up the process of loading and reloading the firearm as several rounds can be loaded at once, rather than one round being loaded at a time. The term "clip" is also frequently used to refer to a detachable magazine, though such usage is incorrect.

Every once in a while something goes wrong and your favorite BB shooter stops working as it should :( One of the most common problems I see with many of the full blowback BB and Airsoft pistols are BB's getting stuck in the gas tube. This is because this style of gun loads a BB into the breach area of the barrel every time you rack the slide forward. Of course this is only when there are BB's in the magazine.

The semi auto style of these guns is similar to that of a real gun, the blowback operates the slide which in turn moves back and then forward and loads a BB into the chamber. With a real gun, if you where to rack the slide manually again without shooting it, the chambered round would be ejected by the extractor but with a BB gun there is no extractor because there is no spent shell to eject. So multiple BB's can be loaded into the chamber area of the barrel overloading it and if the BB's have nowhere to go they just jam up and often go back into the gas tube which can cause all kinds of problems...

In this Cybergun KWC Tanfoglio Witness 1911 Stuck BB Removal Tutorial Video, I show you how to remove a BB or even multiple BB's from the gas tube area which in short requires; the removal of the slide and guid rod and spring so that you can push the gas tube forward and shake the BB out of the front of the gas tube.

Watch my Vimeo Video on how to remove a stuck BB from the Gas Tube on my Tanfoglio Witness 1911.

Buy KWC/Cybergun 1911 BB in Canada   -   Buy KWC/Cybergun 1911 BB in the US

I don't often get to shoot my airguns out at the 100 foot mark but I purchased my Sheridan Silver Streak .20 Caliber Multi Pump Pellet Rifle mainly to shoot up to and even past this fairly distant range as the Silver Streak is my new vermin gun for pests around the farm. I get a lot of Crows that to be honest are just feathered bullies that pick on all the other friendly birds on the farm, they have also been known to get into my garbage and even attack the Eagles and Hawks in the area. Flying Rats I like to call them.

In this Field test Shooting video I test out my brand new Sheridan Silver Streak on the Chronograph to see just how powerful it really is not just at the maximum 8 pumps but also at 3 and 5 pumps. I was actually very surprised at the very decent power I got from only 3 pumps (460 fps), you could easily take out a small rat with the 14.3 grain .20 caliber lead pellets I was using for my Chrony test.  At 5 pumps I gained close to another 100 fps and at 8 pumps I maxed out at just a hair under 640 fps respectively. With the 14.3 grain pellets I was using this worked out to right around 13 foot pounds of energy. (My Sheridan was purchased using a PAL)

I also shot my Sheridan Silver Streak .20 Caliber Pellet Rifle at a target setup 100 feet or just over 30 yards away and was able to get what I felt was a nice 1.5 inch 5 shot grouping. 4 of the 5 pellets where all within 1 inch of each other with my first shot being a bit lower and to the right of the rest spreading the group out to about 1.5 inches. Keep in mind I was also a bit winded from all the pumping and I could feel and see my heartbeat in my 9 power Bushnell scope making my crosshairs bob back and forth ever so slightly.

I have not shot my Sheridan Silver Streak all that much and plan to hone my skills further so when the time comes I will be ready for them pesky crows.

Stay tuned for my future Table Top review of my Sheridan Silver Streak, for now you can checkout my Preview video that has some preliminary info.

I like to show off some of my acquisitions from time to time even if they are guns I don't necessarily have for sale, I am a collector and some items are not always common enough or even popular enough to keep in our Replica Airguns Store.

Today I show you two blank guns I picked up from a recent gun show I attended in Chilliwack BC. There where not many blank guns at the show, the two I found may have been the only blank guns there, at least that I saw? The ROHM RG300 .22 Caliber Blank Pistol and RST MOD. 1966 .22 Caliber Blank Revolver I picked up for a pretty good price, at least in my mind, $55 for the ROHM and $20 for the RTS. A nice addition to my blank gun collection!

I have been contemplating between a PCP (Pre Charged Pneumatic) or a really good Multi-pump air rifle for pest control around my house, I have been using a spring piston rifle but the combination of my limited skills with spring piston rifles and the fact that most pests in my area stay a good 50+ yards back, means I need an airgun with pin-point accuracy. At the end of the day I decided on the Sheridan Silver Streak because it was a bit more affordable than a PCP air rifle and also the Sheridan is such a classic air rifle but still with the right amount of power and accuracy to get the job done.

Checkout some more photos...

Watch my Vimeo Preview Video of these three guns:

Buy Blank Guns in the Canada Store  -  Buy Blank Guns in the US Store

I have not done my official Table Top and Shooting Reviews for the Gas Blowback Airsoft Cybergun Sig Sauer P226 but I really wanted to cut off the ugly orange painted barrel tip, it was kind of driving me crazy! keep in mind here in Canada we are not required to have orange tips on our Airsoft guns, most of the all metal or all black Airsoft guns imported these days fall into the "airgun uncontrolled firearms" category. If you live in the US or other parts of the world you could be breaking the law if you do this mod so be warned...

Your best best is to simply watch my Vimeo Video as I show you exactly how I removed the orange painted portion of the metal barrel using a hack saw, file, vice and some sand paper. All in all it was not too difficult and only took about 15 minutes to complete...

Buy this Airsoft Pistol in Canada  -  Buy this Airsoft Pistol in the US

I have been asked so many times to make a "How To Video" on cleaning Airguns and Blank Guns so I thought I better make the video so people stop asking me to make one :) and if they do ask, which I am sure they still will, then I will be able to direct them to this awesome video tutorial...

So basically in this video I clean an Airgun that can be field stripped and I also clean an Airgun that can not easily be field stripped. I then clean a blank gun even thought the process is very much the same.

I also talk a bit about cleaners and general air gun maintenance but for the most part I just show you how to clean the guns so watch the video!

I have found one of the more confusion aspects of guns is what defines the trigger action, and I confused this a lot at first but now feel I have a good understanding of what makes a gun Single Action Only, Double Action Only or Single and Double Action.

Your best bet is to watch my attached Vimeo video as it not only describes trigger actions but also has the added benefit of the visual examples of each type of trigger action.

Here is a very quick explanation of what constitutes each type of trigger action:

First off the action is based on the role of the trigger in how it effects the action, not how the slide or the hammer can effect the action of the gun.

A Single Action Only gun does one action (a single action) and that is generally the releasing of the hammer or striker or what have you... Single Action Only guns can not fire without first manually pre-cocking the external hammer or manually pulling the slide or charging handle back first to chamber a round and also pre-cock the action of the gun. Keep in mind that the blowback of the slide or bolt in semi and full auto guns effectively cocks the action of the gun allowing for single action trigger release.

A Double Action Only gun performs dual functions, the pre-cocking of the hammer or striker in the first stage and the releasing of the hammer or striker in the second stage, therefore performing two actions. Double Action Only guns do not have the ability to pre-cock the hammer or striker fully and therefore generally have a heavier trigger pull as the first stage of the trigger is to cock the sprung hammer or internal action.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

Single and Double Action guns have the ability to do both, meaning they can be pre-cocked and then fired or fired without pre-cocking simply by pulling the trigger.

Keep in mind that there are some guns that fall in to their own category, take for example the Glock. Glock has been known to actually describer their guns as Double Action Only, when in fact they can not be fired without the slide first being pulled back to partially pre-cock the internal striker - similar to a single action gun. But when you pull the trigger on a Glock you do not simply release the action but rather the trigger first pulls the striker action back the final stage in order to release it, similar to a double action gun.

Again, watch my Vimeo video as I hope the visuals will help you to understand the differences between Single Action Only, Double Action Only and Single and Double Action trigger.

Related Posts:

• FULL METAL UZI BLOWBACK CO2 .177 BB GUN ON ITS WAY

• CYBERGUN MINI UZI BB GUN REVIEW

• CYBERGUN MINI UZI CO2 BB GUN CHRONOGRAPH AND FULL AUTO SHOOTING TEST

"Before you attempt to do this modification you need to be aware that it may void your warrantee and/or you may fail and either break something or incorrectly reassemble your Mini UZI rendering it "Broked"! This is your problem so please do not attempt this modification (even though it is fairly easy to do) unless you're 100% confident you can do it and are aware of the possible consequences. Make sure to also take into account any gun laws in your area prohibiting full-auto capable firearms!"

(Special thanks to Herman for showing me the ropes on this modification)

This modification will make your semi-auto "only" Cybergun/KWC Mini UZI BB Gun into a full auto capable 4.5mm BB machine gun. From the factory the full auto switch position (Far Left "A") is disabled but the full auto selector position is visible. The actual full-auto functionality is still present in the Mini UZI but has been decommissioned by the simple means of blocking the selector switch from being moved to the far left full-auto or "A" position.

This full auto modification will show you how to disassemble the Cybergun - KWC Mini UZI BB Gun and remove the small plastic selector switch blockage so you will be able to manually switch between semi auto and full auto modes. This modification takes about 15 minutes to complete.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

You will need the following tools: A pair of pliers and either a pair of small wire cutters or a file.

Let's begin! Below are the two pre-modification positions available from the factory:

"S - SAFE"

"R - SEMI AUTO"

Below is a closeup of the top bolt cover that we will be removing to access the internal bolt for removal:

In the next photo we have removed the bolt cover by pressing the "angled button" towards the rear sight:

And now the bolt is removed:

I removed the grips but this is not necessary:

Now you will need to remove the lower receiver pin located at the back end of the receiver closest to the grip safety. Use a pair of pliers to pinch the metal pin while pushing it through. Once the pin is started you can use the pliers on the other side to pull the pin all the way out. You may need to us a fair amount of force to do this as the fit of the pin is tight:

Once the pin is removed the lower receiver can be detached:

You can see in the picture below the small plastic nub that we will need to remove in order to restore full-auto capability:

I used a pair of small wire cutters to clip this plastic nub off, but you could use a file too. Just make sure that the plastic is flush and does not have any burs or protrusions.

Below is a photo of the Plastic Nub removed from another angle:

After that, all you need to do is reassemble you Mini UZI in revers order to finnish the Full Auto modification.

In the below Photos you can see we have restored the ability to move the fire selector switch over to the "Far Left" or "A" position, reenabling the Cybergun - KWC Mini UZI BB Gun to shoot in full auto when desired.

"A - FULL AUTO"

Now enjoy your Cybergun - KWC Mini UZI BB Gun in full-auto as it was originally designed!

Here is my Vimeo Video in Narrative with Photos:

Buy this gun in Canada

Buy this gun in the US

This Article was graciously provided by one of my viewers: Lee

Related Posts:

• SIG SAUER X-FIVE STAINLESS STEEL VERSION

DISCLAIMER, PLEASE READ AND UNDERSTAND!

• This walkthrough is for information purposes ONLY, if you decide to dismantle your BB gun you will void any warranty you have with the manufacturer.
•  I will not be held accountable for your actions or any damage that is caused by your negligence. Therefore, if YOU decide to dismantle your BB gun and break something during the dismantling or assembling it is your problem not mine.
• If you don’t feel confident or comfortable doing any of these steps STOP and do not proceed any further or you may do damage.
• YOU WILL LOOSE ALL THE SIG SAUER MARKINGS ON THE GUN.

Having said all that, this is my first ever instructional so I’m going to try and make this walkthrough as easy as I can for you to understand. You will need the following: Flat tip Screwdriver for the grips, Small Philips Head screwdriver, small punch & needle nose pliers – the last 2 are optional.

Make sure you have a clean work space and lay out every part in the order that you remove it Left to Right, come reassembly time you work Right to Left it makes reassembly so much easier.

Step 1:

Field Strip the slide until it looks like this:

Unscrew these 2 screws, these hold in the “Breech Block” once your unscrewed cup the end of the slide in your hand and let the Breech & Screws fall in your hand – Set these aside.

That’s it your Slide should look like this:

It is now ready for paint removal.

Step 2:

Take the Frame and start removing the grips Left hand side first:

Flip the frame over and remove the right hand side grips:

Carefully remove the trigger return spring, it is under tension and it WILL fly across the room – I spent an hour looking for it one day! Also while we are at it, you can remove the cover to the magazine release.

To remove the safety, place your flat tip screwdriver between the frame and the safety and twist ever so gently this will separate the safety and all you need to do now is grab the safety from either side and gently pull & wiggle until it separates.

Once the safety is removed you will see the safety bar, this lifts off.

Step 3:

Lift this little pin out and remove the spring, very carefully push this pin from the other side and remove, be careful because once this happens your hammer assembly is loose and free from the frame.

Slowly and gently remove the hammer assembly:

Note the little shiny piece that sits on the side of the hammer assembly, try very hard not to let this piece fly out, it is a pain to get back in, if it does fly out keep calm and take your time, don’t force the little spring in, it seats in behind the shiny metal thing – sorry I don’t have a proper name for it.

Also make sure that the spring next to it is in the locked open position, if it snaps back just get the tip of a small screwdriver and slide it to the left until it locks.

The hammer return spring assembly at the back of the grips can be removed and set aside.

Removing the trigger assembly is easier than it looks; you need to remove the takedown lever by rotating it counter clockwise until it stops.

Push it through the frame and rotate it back clockwise to remove it all together.

Remove the screw holding the trigger assembly:

Lift out the trigger assembly; be careful of the slide lock spring it wont Fly out, but it will fall out.

If you want to remove the magazine release, there is a spring that sits at the rear of the trigger guard;

Push the magazine release in part way & with the flat tip screwdriver lifts the up to remove it, once removed the magazine release will simply fall out.

THAT’S IT! We’re done, ready for the paint removal. Any paint stripper is fine.

KEEP IT WELL AWAY FROM THE PLASTIC PARTS!

Follow the manufacturer’s guidelines for use of their product and thoroughly clean the slide and frame after you have removed the paint.

YOU WILL LOOSE ALL THE SIG Sauer MARKINGS ON THE GUN.

Rub over the slide and frame with #0000 Steel wool or 1200 grit Wet & Dry paper. Clean again and using the paper or steel wool with some ALUMINUM polishing compound like Autosol and some good ol fashioned elbow grease polish the slide and frame until you reach your desired outcome. Clean it all down again and wipe it down with a rag that has had gun oil or my preference “Fluid Film”.

Reassemble the gun in the reverse order and viola one shiny SIG Sauer X-Five.

Buy this gun in Canada   -   Buy this gun in the US