Entries in 380,How To

Airgun Safety 101

No Comments

Airguns are not toys and as so require proper storage, transportation and handling so as not to cause an accident that could be minor or even deadly.

No matter if you are handling an Airgun or a “Real Gun”, they should both be handled in the same manner even if the consequences from an accident with an Airgun may be less serious. Life long injuries like the loss of an eye are nothing to be taken lightly.

For the most part, what I talk about in this Airgun Safety 101 video can also be applied to a “Real Gun” although most countries will have stricter laws and guidelines in the storage, transportation and handling of “Real Guns” over an Airgun.




Storing Your Airgun:

In Canada an unregulated Airgun does not have any real specific safe storage guidelines but common sense should be used and I recommend that you at the bare minimum keep your Airgun in some sort of locked space whether it be a safe, cabinet or room that is locked all of the time.

You can also put a trigger lock on your Airgun if you do not have a lockable storage location for it.

You should also make sure to store your Airgun unloaded, at least when it comes to BB’s and or Pellets. If there is some unused CO2 in it, or it is charged with Compressed Air, but unloaded in terms of ammunition, that is OK, but again keep it in a safe location away from anyone that may be able to get their hands on it and hurt themselves or others.




Transporting Your Airgun:

Again, in Canada an unregulated Airgun does not have any real transportation guidelines but if you keep your Airgun out in the open and someone sees it, they will most certainly call the police and more than likely you may find yourself staring down the wrong end of a police firearm, at least until they sort it all out. This is very serious as unfortunately people have died as a result of handling their Airguns out in the open and underestimating what kind of police response that may entail.

For that reason alone, always keep your Airgun out of sight in a case or backpack or the trunk of your car. Never transport your Airgun loaded and it is best if you can lock it in a case or put a trigger lock on it for added safety when transporting it.



Shooting Your Airgun:

Shooting your Airgun is always the most enjoyable part of owning an Airgun, so don’t do something stupid and turn that experience into a nightmare. Treat your Airgun as if it is deadly at all times, never point it at anything you do not intend on shooting.

Keep your safety on until you are ready to shoot. Never put your finger on the trigger until you are ready to shoot it and only shoot it in a safe location with an appropriate background and backstop.

Think of the barrel of your Airgun as a light saber that if it crosses even your arm, it could cut it off. Even a BB to the arm is a serious matter. I had a friend that shot himself in the arm with a BB Gun and the BB lodged in the tendons of his wrist requiring an operation to remove it. He was a violin player so this could have ended his violin playing, but luckily he was OK.

When Your finger is not on the trigger it should be held across the trigger guard in a straight position to ensure no accidental misfires.

Wear eye protection, Steel BB’s will bounce back when they hit a hard surface and can come back with enough force to injure an eye easily. Generally Airguns do not require ear protection but some can be loud enough that you may want to wear some sort of ear protection as a precaution.

Only shoot with others that are responsible and take Gun Safety very seriously. Young people will need constant supervision and it is best to go through all of this first before even considering handing them an Airgun for the first time. Perhaps start them off with something like an Airsoft gun which will have less consequences if an accident were to take place.

Airguns are awesome in so many ways and allow for a similar shooting experience to a “Real Gun”. They can be used in more situations, with less overall cost and are a great way to learn proper gun handling and how to improve your shooting ability even if you are a “Real Gun” owner. Always be responsible with your Airgun not only for yourself but for others as it only takes a few idiots to ruin things for the rest of us. Don’t be that Idiot please!

Categories: Airsoft, BB, Blank Gun, Gun Law, Gun Safety, How To, Pistol, Pellet, Paintball, Real Gun, Vimeo Video Tags:

Top Most Popular Replica Airgun Pistol Design Types

No Comments

This is not exclusive to Airguns since trends of Airguns are highly influenced by what type of Real Steel Pistols are popular to people. This is often based on what people see portrayed in movies and TV Series, and also promoted online. There is for sure an overlap in what is popular and it is hard to say what is influencing what? Is it the popularity of Pistols out in the real world that influences what we see being used in the movies and on TV? Or is it what we see in Movies and TV that influences our choices of pistols out in the real world? Perhaps it is a combination of both?

My list is based on my own personal experience and does not represent the entirety of types of Pistol designs available.

  • Glock

  • Sig Sauer

  • 1911

  • Beretta 92 / 84

  • S&W M&P

  • Makarov / Walther PPK

  • 357 / 44 Magnum / Colt Single Action Army

  • Desert Eagle

  • UZI

Buy Airguns in Canada

Buy Airguns in the US

Categories: .43 cal, .22 cal, 4.5mm / .177 cal, 6mm, 9mm, 380, Airsoft, BB, Blank Gun, Blowback, CO2, Comparison, Full Auto, Gas, GBB, Non Airguns, Pellet, Pistol, Paintball, Real Gun, Review, Revolver, Semi Auto, Vimeo Video Tags: Glock, Sig Sauer, 1911, Beretta, S&W M&P, Makarov, Tokarev, 357, 44 Magnum, Colt Single Action Army, Desert Eagle, UZI, Mini UZI

Reasons why Replica Airguns are Better than Real Guns

No Comments

Cost:

Airguns are generally cheaper to buy and for sure cheaper to shoot. Airguns can cost as little as $50-100 to buy while real guns in similar models will cost many time more. Cost of ammo is so much less expensive than Real Gun ammo by a mile!

Difficulty to Obtain:

Airguns in most countries do not require any licensing or registration. Generally there are more available options in Airgun choices than Real Gun choices as restrictions often prohibit many Real Guns to be obtained.

Places to Shoot:

Unless you live in a super remote locations and your laws allow you to shoot Real Guns in those locations, then in most cases you can shoot an Airgun almost anywhere within reason. You can even shoot certain Airgun models in your basement. Airsoft is a great option for indoor shooting as the plastic ammo does not carry very much energy so with minimal effort you can make a backstop that will trap the ammo very well.

Trigger Time:

Because ammo is much less expensive and places you can shoot are easier to find, you can get a lot more Trigger Time under your belt which will also improve your shotgun with Real Guns and after all it’s just fun to shoot guns even if they are Airguns.

Safety:

I am not talking about safety in terms of protection. I am talking about safety as in if you do something stupid and your Gun goes off accidentally. If you accidentally fire your Airgun indoors, the bullet will not travel through floors or walls and potentially harm or kill someone on the other side. If you do manage to shoot yourself with an Airgun, the consequence are much less severe than shooting yourself with a Real Gun. That said, always treat an Airgun as if it was a Real Loaded Gun, as server injury and even death can occur even with an Airgun.

Ware Games and Training Situations:

There is no way you can use a standard Real Gun to shoot at people, unless extensively altered with special parts that make the Real Gun unusable to shoot live ammo. With Airguns you have the choice of using an Airsoft or Paintball gun that are both designed specifically for this purpose.

Pest Control:

If you have the need for pest control in an urban area where you do not want a stray bullet to travel too far or penetrate buildings if a shot where to go awry, then an Airgun designed for accuracy and power may be perfect for the job. Accuracy with target and hunting Airguns is on par if not better than many Real Guns and are have powerful enough to kill a pest humanely without having too much power for the job and having to worry as much about your background.

Prop Guns:

As mentioned already, Airguns can look a lot like Real Guns, so they are perfect to be used as a stand-in or Prop Gun when you need to simulate the look and function of a Real Gun. Again they are easier and cheaper to obtain and if something does go wrong, the consequences are much less severe.

Social Stigma:

Unfortunately Real Guns and perhaps any gun these days are looked upon with a social stigma as being the cause of the Crime rather than a tool used in a Crime. And so people blame Guns for these crimes rather than the people committing these crimes. If a person is motivated enough to do something bad, they are going to do it either way and will use whatever means is available to them to commit these Crimes. Including other means like: Knives, Blunt Objects, Poisons, Vehicles, Explosives… Sad but true! Airguns are not used in homicides or mass shootings as they are completely underpowered for a crime like this. They can however be used in crimes as a show of threat, as they do look a lot like real guns, generally people that use Airguns for real crimes, if challenged will give up immediately as they are completely outgunned. Don’t bring an Airgun to a Real Gun fight, you have better chance with a knife!











Categories: Comparison, Gun Safety, Pistol, Real Gun, Rifle, Vimeo Video, .20 cal, .22 cal, .43 cal, .50 cal, .68 cal, 10mm, 380, 4.5mm / .177 cal, 6mm, 8mm, 9mm, AEG, Airsoft, BB, Blowback, Break Barrel, Bulk Air, CO2, Full Auto, Gas, GBB, Gun Law, Non Airguns, Paintball, PCP, Pellet, Pump, Q&A Video, Repeater, Revolver, Semi Auto, Single Shot, Spring Piston Tags:

Airgun Magazine Types Explained - BB - Pellet - Airsoft

No Comments

There are many types of magazines used in Airguns and some of this is dependent on the ammunition used.

For instance a stacked type of magazine often used for Steel BB and Airsoft can not be used for Pellets as pellets tend to deform when stacked in such a way since there is no metal casting protecting them from mashing into each other.

So what type of magazines do we generally see in Airguns? The most common Airgun magazines are as follows:

Simple Stick Magazine

  • Mostly used with Steel BB but also found in some Airsoft Airguns.

  • Some Pellet Airguns use a type of stick magazine with a rotary magazine on each end.

  • Used in non-blowback and blowback Airguns.

  • Can be made from plastic or steel or a combination of both materials.

Full Size Drop Out Magazine

  • Used with Steel BB and Airsoft guns.

  • Generally you will find these types magazines hold both the BB’s and CO2.

  • Used in non-blowback and blowback Airguns.

  • Commonly used with Airsoft Rifles in mid to high capacity.

  • Can be made from plastic or steel or a combination of both materials.

Rotary magazine

  • Used with Steel BB, Airsoft and Pellet Airguns.

  • Used in non-blowback and blowback Airguns.

  • Can be made from plastic or steel.

  • Can often use mixed ammo types as in both 4.5mm Steel BB and .177 caliber pellet.

Belt Fed Magazine

  • Like rotary magazine belt fed magazine can accommodate Steel BB, Pellet and Airsoft but are most often used with Pellet Airguns.

  • Usually found in a full size magazine that also holds the CO2.

  • Used in non-blowback and blowback Airguns.

  • Can be made from plastic or steel or a combination of both materials.

Internal Magazine

  • Used with Steel BB, Airsoft.

  • Can have a hopper built in hat feeds a spring fed magazine.

  • Usually found in lesser expensive Airguns but not a rule.

In this Video I go through each type of Airgun Magazine and talk about their differences and uses.

Categories: 4.5mm / .177 cal, .22 cal, 6mm, AEG, Airsoft, BB, Blowback, CO2, Comparison, Bulk Air, Gas, GBB, How To, Pellet, Pistol, Review, Revolver, Rifle, Vimeo Video Tags:

ROHM RG-89 .380 Caliber Blank Revolver Field Test Shooting Review

No Comments

If you haven’t already watched My Table Top Video Review for the ROHM RG-89 .380 Caliber Blank Revolver than make sure to do so for the full features and specifications.

My Field Test Shooting videos for blank guns are pretty basic! I can’t test for accuracy since there is no bullet hitting a target and similarly since there is no bullet I can not test the velocity or feet per second power. SO what is there really left to test?

I guess will the blank gun I am testing fire when I pull the trigger? That’s all there is to really test. You may ask why even make a Field Test Shooting Video for a blank gun if you can’t test accuracy and power. I’ll tell you why… Because it’s just fun and it looks good on camera :)

So watch my YouTube video of me popping of some .380 caliber blanks with my ROHM RG-89 .380 Caliber Blank Revolver inside the Sea Can Airgun Shooting Range.

Categories: Blank Gun, Field Test, Pistol, Revolver, Review, YouTube Video, 380 Tags: ROHM, RG-89

ROHM RG-89 .380 Caliber Blank Revolver Table Top Shooting Review

No Comments

Type: Blank Revolver.
Manufacturer: ROHM (RÖHM).
Model: RG-89
Materials: Mostly Metal.
Weight: 1.45 pounds (658 grams).
Barrel: Front firing designed for attaching a flare adaptor.
Propulsion: Gun powder.
Action: Single & double action.
Ammunition Type: 9mm / .380 caliber crimped.
Ammunition Capacity: 6 rounds.
FPS: N/A.

Trigger Pull: The trigger pull on the ROHM RG-89 .380 Caliber Blank Revolver in single action is fairly light weight with virtually no take up at all as you would expect from a revolver. The double action trigger pull is much heavier with a smooth release. Mechanically the trigger feels really solid.

Accuracy: NA.


Build Quality: The overall build quality for the ROHM RG-89 .380 Caliber Blank Revolver is excellent, being German made its built to last and the fit and finish is typical German quality. There are steel parts where they need to be like in the barrel, pins, screws and reenforcing parts, the rest of the gun is generally made out of a zinc alloy otherwise know as pot metal with only the moulded grips being made out of plastic.

Realism: The ROHM RG-89 .380 Caliber Blank Revolver is not an exact replica of any given gun in production as this would make importing it into Canada even more difficult, but it is styled after a Snub Nosed type Revolver. As for looking like and working like a real gun, the ROHM RG-89 .380 Caliber Blank Revolver looks and sounds as loud as a real gun, of course with the exception of the dangerous bullet coming out of the barrel!


Purchase from: The Replica Airguns Canada Store

Pros:

  • German made Quality.

  • All metal gun with reenforced steel in some areas.

  • Front firing gun.

  • Large caliber makes a bigger bang.

  • Higher 6 shot capacity over RG-59.

  • Chrome (Silver) finish is very nice.

  • Also like the moulded grips on the Chrome version.

  • Comes with Flare Adaptor & Cleaning Rods.

  • Comes in a nice foam lined plastic hard shell case.

  • Right now Rohm is the only blank gun brand we can get in Canada.

Cons:

  •  Double Action trigger pull is a bit heavy.

  • Have to make sure you only shot them where you will not get in trouble. Very loud!

  • Expensive due to them being harder to get and in high demand in Canada.

Comments:
I think the ROHM RG-89 .380 Caliber Blank Revolver especially in the Chrome (Nickel) version is one of the nicest looking ROHM Blank guns we stock. The additional size over say a ROHM RG-59 makes it feel a lot more beefy in the hand, you also get the extra 6th 9mm / .380 caliber blank with the larger cylinder of the ROHM RG-89 .380 Caliber Blank Revolver. Anther bonus with the Chrome or Nickel version is that you get moulded grips that again I feel looks and fells better in the hand. Along with the ROHM RG-88, the ROHM RG-89 .380 Caliber Blank Revolver is one of my Top ROHM Picks!

My Full Video Review for the ROHM RG-89 .380 Caliber Blank Revolver:

Categories: 380, Blank Gun, Comparison, Pistol, Review, Revolver, YouTube Video Tags: ROHM, RG-89

December Christmas Update Video 2018

No Comments

In this December Update Video I wish everyone a Merry Christmas and Happy New Year. If you have other beliefs and perhaps don’t celebrate Christmas in the traditional Canadian fashion then I wish you a Happy Holiday!

I received a number of products lately and really don’t have time to do full reviews of them as the Holliday season is on us which is going to limit how many videos I can pump out over the next couple of weeks so hopefully this Update video will keep everyone excited about the future Replace Airgun Videos.

Here are the items I talk about in this December 2018 Update Video:

Sig Sauer ASP M17 CO2 Blowback Pellet Pistol

Sig Sauer Fake Suppressor for P226 ASP Pellet Pistol

Umarex Steel Strike Full Auto BB Rifle

ROHM RG-89 .380 Caliber Blank Revolver

Umarex Legends WildCard Airsoft SAA Revolver

Umarex WW2 Limited Edition P08 CO2 Blowback BB Pistol

Umarex WW2 Limited Edition M712 Full Auto CO2 Blowback BB Pistol

Webley Mark VI CO2 Pellet Revolver

John Wayne Signature SAA Revolver Solid Maple Wood Case

Categories: 380, 4.5mm / .177 cal, 6mm, Accessory, Airgun News, Airsoft, Airsoft News, BB, Blank Gun, Blowback, Blank Gun News, CO2, Full Auto, Pellet, Pistol, Replica Airguns News, Revolver, Rifle, Semi Auto, YouTube Video Tags: Sig Sauer ASP

Replica Airguns Silent Auction of Hard to Get Canada Blank Guns

2 Comments

I have some harder to get here in Canada Blank Guns that I am selling from my personal collection by way off Silent Auction. These Blank Guns are more for the Canadian collector and perhaps not so much for the first time buyer. I would recommend for the first time Blank Gun buyer that you checkout our selection off brand new ROHM Blank Guns that we sell in our Canada Replica Airguns Store so check those ROHM Blank Guns out as they are excellent German made Blank Guns in a variety of styles.

Getting back to the Blank Guns in my personal collection. They are all previously owned, most only test fired once for review. Below is a listing of the Blank Guns I am offering in this Silent Auction with what I feel is there approximate value:

Here is how the silent action system works… First of all I will only be shipping these guns within Canada to a Canadian addresses and all funds are in Canadian Funds. You will need to email me and let me know which Blank Gun or Blank Guns you are interested in bidding on and let me know what your best price is. In approximately a weeks time when I feel enough offers have come in, I will then contact the winning bidder and give them 24 hours to pay up. If they do not pay me the amount they offered within the 24 hours I will then move on to the next highest bidder.

If you are bidding on more than one gun then I will take this into consideration since collecting money and shipping product to one buyer is easier than multiple buyers so this will help you with your offer.

I also will be charging $20 for shipping per gun, if you are buying multiple guns then I will discount the shipping a little bit so I will not charge you $20 per gun.

Email me here:

Categories: Silent Auction, YouTube Video, 8mm, 9mm, 380, .22 cal, Blank Gun, Pistol, Replica Airguns News, Semi Auto, Revolver Tags: ROHM, Bruni Mod. 92, EKOL, Aras, ARDA, ARAL, ARAL 622K

The Best Way to Hold Your Airgun

No Comments

I made a similar video about how to hold your airgun a while back but sometimes they get a bit buried in all the video I make. I feel it's really important how you grip your gun even if it's only an airgun with very little kick or recoil. Proper pistol grip is something you should use no matter what so that you can carry it forward to what ever gun you are shooting.

More kick or recoil means a firmer grip is required to hold the gun so when shooting a powder burner with lots of kick grip becomes even more important.

In this video I go over the proper two handed grip to use when holding a pistol, which hand to hold lose and which had to grip tight, how to overlap your fingers and thumbs.

Categories: Airsoft, BB, Break Barrel, CO2, Blowback, How To, Non Airguns, Paintball, Pellet, Pistol, Real Gun, YouTube Video Tags:

Why is My CO2 Airgun Not Working?

23 Comments

One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

  • Did you put a new CO2 cartridge in it and is it pierced all the way?

  • Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

  • Is the safety off?

  • If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, GBB, How To, Pellet, Pistol, Review, Semi Auto, YouTube Video Tags:

Why is My Blank Gun Not Working?

6 Comments

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Categories: .22 cal, 380, 6mm, 8mm, 9mm, Blank Gun, How To, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags:

Gletcher NGT NGT-R CO2 BB and Pellet Revolver Follow-up

No Comments

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Categories: 4.5mm / .177 cal, BB, CO2, How To, Pellet, Pistol, Review, Revolver, YouTube Video Tags: Gletcher, NGT, NGT R

How to Get Rid of That Ugly White Writing on Your Airgun

1 Comment

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, How To, Pellet, Pistol, Review, Revolver, Semi Auto, YouTube Video Tags: Cybergun, KWC, Umarex

Which Shells Work in Which Shell Loading Revolvers?

No Comments

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, CO2, Comparison, How To, Pellet, Pistol, Review, Revolver, YouTube Video Tags: 357, ASG, Colt Single Action Army, Dan Wesson, Dan Wesson 715, G731, Gletcher, KWC, NGT, NGT R, Umarex, Webley

Mike's Personal Guns For Sale - Blank Guns

1 Comment

I will be showcasing here on the Replica Airguns website and over on the Replica Airguns YouTube channel a series of videos I will be making for the purpose of selling some guns out of my personal collection. I simply have no more room for the new guns and in some cases I either have duplicate guns or very similar versions so there is no need to have both. Some guns I am less attached to and as I already stated I need to make room for some of the new stuff I will be reviewing.

To start this series off my first video is to highlight the blank guns I am selling, there are only 4 of them, all of which are really hard to get here in Canada so I am not going to let them go cheap. By the way I am only selling to Canadian residents since shipping cross borders is a little sketchy.

Make sure to watch my above YouTube video to see the blank guns I am selling and instructions on how you can take part in the sale and purchase of them.

Here is a list of the blank guns I am selling from my personal gun collection:

EKOL ASI 9mm Full Auto Front Firing Blank Machine Pistol $725

EKOL Lady Chrome 9mm Front Firing Blank Pistol $400

EKOL Arda 8mm Blank Front Firing Compact Revolver $200

Bruni ME Ranger 1873 SAA .380 Blank Revolver $300

Categories: 380, 8mm, 9mm, Blank Gun, Full Auto, Pistol, Revolver, Semi Auto, YouTube Video Tags: ARDA, Bruni, Colt Single Action Army, EKOL, EKOL ASI UZI, Lady, ME Ranger

Airgun Do’s & Don’ts

No Comments

When I say Airguns, I am referring to pretty much all BB, Airsoft, Pellet, Paintball and even Blank guns for most of the topics listed here.

Do’s:

  1. Treat your Airgun just like you would a real gun. If something goes wrong, perhaps the outcome will not be as severe but do you really want to take a trip down to your local emergency ward to get a BB or Pellet removed?

  2. Always assume your airgun is loaded, for some reason it always seems those empty guns are the ones that do the most damage.

  3. Be discrete, If it looks like a gun other people will think it is a gun so don’t flash your airguns around in public. Keep it in a case when transporting and shoot it in an area that will not alarm other people.

  4. Always wear eye protection when shooting your Airgun. Do you really want to shoot your eye out? No Joke!

  5. Be aware of your surroundings like windows, hard objects that could make your ammo bounce back at you. Make sure you are shooting your Airgun in a safe direction at all times, know your target and beyond.

  6. Use Airguns to teach others and learn how to safely and effectively shoot a gun. Airguns can be less intimidating then a real gun (Not so loud and very little recoil) and make for great start out and transitions guns.

  7. Use Airguns to get more inexpensive trigger time and become a more experienced shooter. Airguns cosy only pennies per round to shoot and can be shot in way more areas than a real gun can, practice makes perfect so get shooting!

  8. Use Airguns in areas where real guns may not be allowed or safe to use. Again, Airguns can be shot in all kinds of places, in your back yard or even in a properly setup indoor home range.

  9. Use Airguns with adequate power for safe and humane pest control where real guns may be prohibited.Airguns are quiet and less likely for the bullet to travel long ranges which makes them ideal for close range pest control in areas where real guns are too loud and to powerful.

Don’ts:

  1. Do not assume because it is an airgun it is not dangerous or simply a toy. Many Deaths have been caused by Airguns along with a lot of pain and suffering so treat your Airgun with respect. It is not a toy or you would find them in the toy department at your local store along with yo-yos and stuffed animals.

  2. Do not point or shoot at people unless of course you are using an Airsoft gun in an Airsoft field or facility. Yes Airsoft guns are meant to shoot at each other (with appropriate attire like eye protection and full body clothing), but steel BB and Pellet can cause serious injury especially at close range and on direct skin contact.

  3. Do not leave your Airgun loaded, you never know who is going to come across it and accidentally discharge it. Remember, a loaded gun is a dangerous gun in the wrong hands. You may know better than to assume the gun is undulated but children and even adults without any gun training will most definitely handle the airgun without consideration of the danger it poses.

  4. Do not use an Airgun for self protection. See my related video. Simply put, Airguns are not practical for self defense because they rarely have enough Stopping Power. The ones that do have enough power need to be pre-charged and in most cases are only single shot meaning if you miss or don’t get the job done no the first shot then you are done.

  5. Do not use an underpowered Airgun for pest control. See related video. Using a low powered BB pistol for pest control is cruel, you will only injure the animal making it suffer unnecessarily. Use a high powered pellet rifle to get the job done.

  6. Do not take your gun apart, in most cases this will void the warranty and the reality is that airguns rarely need to be cleaned since no dirty gun powder is used. lead pellet rifles may require occasional barrel cleaning to keep the rifled barrel free of debris.

  7. Do not over oil your Airgun, a little goes a long way and too much oil will just attracted dirt, use the right airgun oil and just enough to keep part functioning smoothly.

  8. Do not over pump an Airgun. Over pumping an Airgun can cause damage to valves and seals and in a worse case situation a rupture the air pressure reservoir or even cause the airgun to explode!

Categories: .20 cal, .22 cal, 380, 4.5mm / .177 cal, 6mm, 8mm, 9mm, AEG, Airsoft, BB, Blank Gun, Blowback, Break Barrel, Bulk Air, CO2, Full Auto, GBB, Gas, Multi-pump, PCP, Paintball, Pellet, Pistol, Repeater, Revolver, Rifle, Semi Auto, Single Shot, Spring Piston, YouTube Video Tags:

Can I put real 1911 Grips on my KWC-Cybergun 1911 BB-Airsoft Gun?

No Comments

With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.

The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.

In this Vimeo Video I demonstrate using grips that fit a real 1911 and show you just exactly where you will need modify them to fit on the KWC and Cybergun CO2 Blowback 1911 pistol series.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blowback, CO2, Comparison, How To, Modification, Pistol, Real Gun, Semi Auto, YouTube Video Tags: Colt Government 1911, Cybergun, KWC, Model 1911, Tanfoglio Witness 1911

Top 10 Most Common Airgun Questions and Discussions

No Comments

Categories: .22 cal, .43 cal, .68 cal, 380, 4.5mm / .177 cal, 6mm, 8mm, 9mm, AEG, Airsoft, BB, Blank Gun, Blowback, Break Barrel, Bulk Air, CO2, Comparison, Full Auto, GBB, Gun Law, Gun Safety, Multi-pump, Non Airguns, PCP, Paintball, Pellet, Pistol, Real Gun, Revolver, Rifle, Semi Auto, Spring Piston, YouTube Video Tags:

No Orange Tip On Your Airsoft Gun! Are You Insane?

No Comments

Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.

It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...

In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.

The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.

Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.

I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.

Categories: 4.5mm / .177 cal, 6mm, Airsoft, BB, Blank Gun, Comparison, Gun Law, How To, Pellet, Pistol, Q&A Video, Revolver, Rifle, YouTube Video Tags:

Clay Pigeons as Reactive Targets for Airguns and Airsoft Guns

2 Comments

If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

 
Categories: Field Test, How To, Review, YouTube Video Tags: Desert Eagle, KWC