Type:AEG Airsoft Rifles Manufacturer:Umarex. Model:Elite Force M4 CFRX Materials: Mostly plastic/some metal. Weight: 5.2 pounds (2360 grams). Total Length: 32.4-35.4 inches (820-900mm). Barrel: 16.1 inch (410mm) barrel non-rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: 6mm plastic Airsoft BB’s (Eye Trace compatible). Ammunition Capacity: Mid/High cap 340 round magazine. FPS: 370-400 fps.
Trigger Pull: The trigger pull on the Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle is fairly short and light as it is basically a simple on and off switch as it is not mechanical but rather electrical. For this reason there is no real creep or feel of a release. When you get to a point in the trigger you close a circuit that activates the electric motor cycling the spring shooting in either semi or full auto depending on your selector switch position at the time.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle, I am planning to make a video for this rifle at the end of this week if all goes as planned. I do not have any of the “Eye Trace” Airsoft Ammo to show how this works and looks but I will be able to do my traditional accuracy and velocity testing here in the Replica Airguns Indoor Sea Can Airgun Range. When I do get access to some of the Eye Trace Airsoft Ammo I will make a short video most likely in a lower light situation to show how it looks.
Build Quality: The Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle does have a lot of plastic in the build including the upper and lower receiver, hand guard, rear stock, front and rear sights, grips and flash hider but as expected there are metal part where they are required as in the inner and outer barrel, magazine, buffer tube, trigger, selector switch, magazine release, charging handle, dust cover and of course many internal parts. It does have a decent weight to it being a fairly long AR and so it feels solid enough. I would have liked to have seen metal sights and perhaps a metal receiver since it is not a cheap or inexpensive AEG Airsoft Rifle.
Realism: The Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle is based on the M4/M16 platform of course in a modern version with all the tactical additions. It looks and feels the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of it. The addition of the Tracer element will add to the realism when shooting it in low light situations, but so far I have not tested it as I do not have any Eye Trace Ammo on hand.
Pros:
Eye Trace System unique and great in low light situations.
Lots of accessory mounting options with Picatinny top rail and side adb bottom M-LOK.
Full adjustable Pop-up sights.
Pre-installed MOSFET for improved electronic performance.
Ver 2 Full Metal, fully upgradeable gearbox.
6 position adjustable AR compatible type rear stock.
I like the two tone black and tan finish.
Has the Elite Force Branding from Umarex.
Easy to get at adjustable Hop-up.
Cons:
Plastic receiver and orange tip.
Battery options limited due nunchuck compatible space.
Pop-up removable sights are plastic.
Comments:
Umarex introduced the “Eye Trace” line of Airsoft Rifles at SHOT Show this year and I have been somewhat eagerly awaiting getting my hands on one to try this new system out, but unfortunately we do not have any of the Eye Trace Airsoft Ammo to do that with. I am not sure if Umarex is low on supply or perhaps it was missed in the order? Either way I will be testing out the new Eye Trace Airsoft Ammo when I get my hands on some. in the future. Just to be clear on how this works, the Eye Trace Ammo is florescent and these New Eye Trace Airsoft Rifles have a blue light you can turn on or off that activated the florescent Airsoft Rounds illuminating them to look like tracer rounds coming out of your barrel. The new Eye Trace Airsoft Rifles work just like a standard AEG Airsoft Rifle when using normal Airsoft BB’s, so I can test the Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle as I always do so stay posted for my Official Field Test Shooting Video for it coming out very soon.
My Vimeo Table Top Review for the Umarex Elite Force M4 CFRX Eye Trace AEG Airsoft Rifle:
This is not an Airgun related video, I was away for a week on vacation so I made a video of some of the vacation highlights, watch if you want to or wait for some more upcoming Airgun Videos…
My wife and I just came back from a wonderful trip to Whistler BC Canada where we stayed 5 nights, then we traveled a few hours to Birch Bay Washington US for 3 more nights.
We stayed in our WorldMark Timeshare which is always very enjoyable and invited up some good friends and relatives to come and join us for part of each trip. It was a lot of fun being able to spend some of our vacation time with good people!
It was a vacation first and foremost but I like to document my trips al least to some degree with video. So I am able to share parts of the vacation with everyone using my Meta Glasses, HoverAir X1 Selfie Drone, Insta360 X4 and GO2 cameras and even a drone shot of me playing around flying my mini Pavo Pico FPV Drone around the hotel in Whistler.
I hope you enjoy the video of our various walks, outings and just simpel hotel lounging around. If you are thinking of going for a vacation in Whistler or Birch Bay, this video may give you a bit of an idea of what you can expect.
Here is Bonus Video Five in my series of Full Auto Fun videos I make each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this Fifth Bonus Full Auto Fun Video I bring out a past Full Auto Fun Airgun that I just couldn’t resist takin out for some full auto fun once again. The WE AK74UN Gas Blowback Full Auto Airsoft Rifle has got to be one of the hardest blowback Airguns I have shot, I would say even a bit more blowback feel than the KWA Mini UZI! The WE AK74UN Gas Blowback Full Auto Airsoft Rifle also does a great job of keeping Airsoft BB’s on target even in full auto with all that recoil as you will see in this video as I dial it in part way through my walk about. Unfortunately we do not sell anything like this anymore at least in Airsoft, the closest thing to it is the Crosman AK1 Blowback CO2 Full Auto BB Rifle which is still a lot of fun with a bit less recoil but a higher rate of fire.
Here is video four in my series of Full Auto Fun videos I make each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this fourth Full Auto Fun video, I retest the Barra 400e 4.5mm BB AEG Full Auto BB Rifle in full auto this time, and try a bit of a different camera angle approach with my HoverAir Drone Camera switching it to follow mode as it doesn’t stop recording so easily in this mode. And as expected, it worked a lot better for me with this setup and continued recording the entire video. I also recoded using my Meta Glasses to get the first person view and like the other videos I placed my Insta360 X4 camera on the barrel again to get some cool up front gun angle shots. I think this setup works well and will probably use it for future Full Auto Fun Videos where I am running around the yard shooting stuff. Maybe there will be a couple more bonus guns in this years Full Auto Fun Series? No promises!
Here is video three in my series of Full Auto Fun videos I make each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this third Full Auto Fun video I test out the Crosman A4-P AR Pistol and like my other videos it was not “picture perfect” or should I say “Video Perfect”… My cameras actually cooperated pretty good this time around, but one of my magazines had an issue (May have been me), so I had to switch over to my trusty KWA 1911 CO2 Blowback BB pistol to finish the job, good ting I had it on me, got to expect the unexpected!
Here is video two in my series of Full Auto Fun videos I make each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this second Full Auto Fun video I test out the classic KWA Mini UZI Blowback CO2 4.5mm BB Machine Gun, at least with this video I did actually shoot in full auto but the video did not go without a few hiccups as my HoverAir Drone decided I was stopping for too long to take my shots and turned itself off a couple of times. And my Meta Glasses decided to get chunky on me and lower their frame rate down to a rather hard to watch frame per second. I did eventually make it though this video but it cold have gone better. No I am not redoing this one as it was shot in Full Auto this time which is what I promised. I can not promise all my tech gear will cooperate exactly s expected but I was able to get some decent footage overall if you can ignore the choppy video for the Meta Glasses for part of the video.
I try to make at least one series of Full Auto Fun video each summer where I pick a few Full Auto Airguns and record some fun outside shooting with them. In this years Full Auto Fun Video series I do a bit of a walk around on my property and shoot a bunch of water filled pop cans. Maybe this doesn’t sound super exciting but I do use some really creative camera angles to capture it all which makes it lot more interesting to watch for sure!
In this first Full Auto Fun video I start with the Barra 400e 4.5mm BB AEG Full Auto BB Rifle, but in the all the camera and audio setup confusion, I forgot to put it in Full Auto (getting old), so this is really not a Full Auto Fun Video, it was still fun and I hope you enjoy it anyway. The other videos in this Full Auto Fun Series are for sure in Full Auto and I will be taking out the Barra 400e and give it another go in Full Auto this time so stay posted for the true Full Auto Fun Video for the Barra 400e shortly!
I have only tested out another similar Crossbow setup one other time so this is not my normal Field Test Review. Like last time when I made my Bear X Desire XL Crossbow Field Test Video, in this Field Test Video I record my Chronograph velocity for the CenterPoint Hornet Recurve Compact Crossbow at the same time as I shoot at the target so I did not have to make two separate video segments and basically did it all in one go. I did have a bit of a brain fart and forgot I needed to setup two separate cameras, one on the Chronograph and one on the Target, as I generally only need one camera at a time for my usually two segment Field Test Videos. So getting to the point, I did not have dedicated camera on the target while shooting and in hind sight it would have been better to have the camera on the Target rather than the Chronograph as my camera glasses generally record the Chronograph readings for me too. I do walk up to the Target at the end of the video so we do get to see exactly where all the bolts landed, so I can show you the final result at the end of the day.
In terns of velocity, CenterPoint claims a velocity of 191 fps. I was able to get consistently just over 180 fps so pretty close. My Chrono readings using the included 147 grain 6.5 inch aluminum bolts ranged from 180 to 182 fps so very consistent. This gave an overall Foot Pound energy of 10.61 foot pounds so velocity and foot pound energy were just a little bit under the claimed rating! This is enough for small pests for sure, it really comes down to accuracy at this point as you will want to get either a head or shoulder area shot for a humane kill, and I am not sure if this bow is up of the job? You will have to see how accurate it will be for you and make that decision for yourself..
In terms of accuracy I found the CenterPoint Hornet Recurve Compact Crossbow to be fairly accuracy on the windage side (left and right), basically with all the bolts only being about 2 inches apart side to side. Where it did not perform as well was in elevation with the bolts ranging about 8 inches top to bottom. I am not sure why this was the case as the velocity is very consistent and generally less consistent velocities account for elevation changes. All the bolts hit the target using the included red dot with no pre adjustments but it did shoot just a bit to the right and maybe overall a bit low. This can easily be corrected using the red dot windage and elevation adjustments.
Interestingly the CenterPoint Hornet Recurve Compact Crossbow has a higher claimed velocity over the Bear X Desire XL Crossbow I tested a while back, yet the Bear X Desire XL Crossbow actually shot a bit faster hitting 190+ fps, not a huge difference but an interesting observation. The CenterPoint Hornet Recurve Compact Crossbow does come with a red dot but both have Picatinny Rails so Red Dots will fit on both Crossbows no problem. I am going to address the elephant in the room, if you compare both of these Crossbows they are virtually the same with the exception of the branding and distribution of them. So I would say get either one, the Bear X Desire XL Crossbow is actually less money as it does not come with an included Red Dot but at least right now it is out of stock so your only option may the the CenterPoint Hornet Recurve Compact Crossbow, both are a lot of fun and pack a lot more punch than your standard non regulated Air Rifle.
Trigger Pull: The trigger pull on the CenterPoint Hornet Recurve Compact Crossbow is a single action only trigger as you need ot cock the bow in order for the trigger to be engaged. The trigger mechanism basically just pushes the bow string up and over the lip of the rail releasing it so there is a bit of friction and I would say it is about 10 pounds maybe a bit less. The safety is also engaged when you cock the bow requiring you to take the CenterPoint Hornet Recurve Compact Crossbow off safe before shooting as an added layer of safety.
Accuracy: I have not made my Field Test Shooting Video for the CenterPoint Hornet Recurve Compact Crossbow and so I am not sure what to expect from it. I have shot a similar bow, the Bear X Desire XL Crossbow so it should perform similar to that one if you want to check that Field Test Shooting Video out, but I expect the CenterPoint Hornet Recurve Compact Crossbow to have a little bit more power as it has a rated fps and draw weight a little bit higher than the Bear X Desire XL Crossbow, we will see?
Build Quality: The CenterPoint Hornet Recurve Compact Crossbow is actually made pretty decently, yes it is mostly plastic and light weight but feels sturdy enough to hold, the bow itself is fiberglass and the only real metal I can confirm is the cocking rail, mostly everything else other than the nuts and bolts that hold it together are some sort of plastic, The only part that does not feel up to par with the quality is the included red dot, it is fairly entry level but I am sure it will get the job done, and if it stops getting the job done at some point you can upgrade it then, or simply use the included rear iron sight which is fully adjustable.
Realism: The CenterPoint Hornet Recurve Compact Crossbow is not a Replica as is what I usually review here on the channel. But I think there is a crossover in terms of interest for a product like this with people that are also interested in Airguns. The other benefit is that it has a lot more power than a non regulated Airgun as the CenterPoint Hornet Recurve Compact Crossbow uses nice heavy 146 grain bolts traveling at almost 200 fps which gives an energy rating of around 12 foot pounds. So if raw power is what you are after, then this is your best option for something still compact if you do not have a firearms license.
Pros:
Fairly inexpensive.
Super light weight and compact.
More power than an Airgun yet still quiet to shoot so you can use discreetly just about anywhere with a good back stop setup.
Easy to draw the bow using the stock for leverage.
Safety is automatically engaged.
Picatinny rail already has iron fully adjustable rear sight and comes with a very basic red dot sight to get you started.
Fiber optic front sight.
3 bolts included.
191 fps (12ft/lbs).
Comes with fore grip.
5 portion adjustable rear but stock.
Cons:
Will need a good backstop or will lose lots of bolts.
Takes a little bit of time to set it up but not too hard, just follow the steps in the manual.
Careful not to wash you hadn't or thumb with the string (Ouchy).
Comments:
The CenterPoint Hornet Recurve Compact Crossbow is a nice crossover product that appeals to Airgun enthusiasts as it does not require a firearms license and can be used in a lot more locations than a standard gun. It also has decent power as compared to a non regulated Airgun hitting 12 foot pounds which is at least 4x more than most non regulated Airguns can achieve. In terms of pest control, it does have the power required for small pests but accuracy is not going to be as good as an Airgun so hitting the rather small sweet spot on a small pest is not going to be easy and you want to be humane about it, so make sure if you do plan on using this for some sort of pest control, that you practice your accuracy and are confident in your shot placement. Personally I would just enjoy shooting it as a target bow that literally cost you nothing after purchase as long as you don’t lose the bolts.
In this Field Test Shooting Video, I test out the Specna Arms Core SA-J73 AEG Airsoft Rifle in my Indoor Replica Airguns Sea Can Shotgun Range to see what the velocity/fps is and what the accuracy is like shooting .20 gram Airsoft BB’s through my Chronograph. I shoot in both semi and full auto at a paper target setup 30 feet down range. If you are more interested in information like details and specifications for the Specna Arms Core SA-J73 AEG Airsoft Rifle, then make sure to watch my Table Top Video I already made that also includes some nice close up video for you to check out…
First up I loaded up a mag of .20 gram Airsoft BB’s and proceeded to shoot 5 rounds through my Chronograph to get a baseline average. Specna Arms claims around 370-380 fps using the preinstalled internal spring setup. I averaged 382 fps with my slowest shot recording 379 fps and my fastest shot hitting 383 fps. All of them really close in terms of velocity and right on the mark of the claimed 370-380 fps using .20 gram Airsoft BB’s.
With the Velocity Test in the bag, I moved on to my Accuracy Test for the Specna Arms Core SA-J73 AEG Airsoft Rifle where I first shot 10 rounds in semi auto to see how tight of a grouping I could get, and then I also finished up the rest of the partially full magazine in full auto to see if that grouping opened up a bit with a lot more rounds and a bit of full auto rocking around. For my 10 shot semi auto grouping I did get around a 1 to 1.5 inch spread, and notably all 10 shots hit the bullseye with no sight adjustments out of the box. Unleashing the Specna Arms Core SA-J73 in full auto, the group did spread out just a little bit to around 3 inches or so, but again right on top of the bullseye for the most part. Very impressive results for sure!
Overall I am super impressed with the Specna Arms Core SA-J73 AEG Airsoft Rifle! At around $200 Canadian you get a well made decent quality AEG Airsoft Rifle that not only looks and feels really good, but performs as good if not better than some much more expensive AEG Airsoft Rifles out there. All you really need to get on top of this purchase would be a decent charger and battery setup along with some quality Airsoft BB’s and then you are ready to go. No need for any more upgrades at least not right away. So if you are looking for an affordable AK type AEG Airsoft Rifle with no real compromises to speak of, look no further than the Specna Arms Core SA-J73 AEG Airsoft Rifle. Not much else will be a better option in this price range.
In this Field test Shooting Video, I test out the Specna Arms Edge SA-X01 AEG Airsoft Rifle in my Indoor Replica Airguns Sea Can Shotgun Range to find out what the velocity is and what the accuracy is like shooting .20 gram Airsoft BB’s through my Chronograph. I also shoot in both semi and full auto at a paper target setup 30 feet away. If you are more interested in details and specifications for the Specna Arms Edge SA-X01 AEG Airsoft Rifle then make sure to watch my Table Top Video I have already made that also has some nice close up video for you to check out…
So first up I loaded up a mag full of .20 gram Airsoft BB’s and proceeded to shoot 5 rounds through my Chronograph. Specna Arms claims around 380 fps using the preinstalled spring setup, I averaged 348 with my slowest shot recording 344 fps and my fastest shot hitting 351 fps, so all of them pretty close in terms of velocity but a bit under the claimed 380 fps using .20 gram Airsoft BB’s
With the Velocity Test completed I moved on to my Accuracy Test for the Specna Arms Edge SA-X01 AEG Airsoft Rifle Field where I not only shot 10 rounds in semi auto to see how tight of a grouping I could get, I also finished up the 120 round magazine in full auto to see if that grouping opened up a bit with a lot more rounds and a bit of full auto shake. For my 10 shot grouping I did get around a 2 inch spread, I did notice the Specna Arms Edge SA-X01 AEG Airsoft Rifle shot really low and a bit to the right out of the box. I would say about 8 inches low and 3-4 inches to the right. There is some sight adjustment you can do so you should be able to dial in the sights to your personal preference. When I switched over to full auto which is always more enjoyable with AEG Airsoft Rifles, the grouping did open up a bit but not a lot more, maybe as much as 4 inches but I did put close to 100 rounds additionally into the target.
Overall I am impressed with the Specna Arms Edge SA-X01 AEG Airsoft Rifle, I would have liked to have seen it shoot a bit closer to the bullseye out of the box using the iron sights, but personally I would more than likely add a red dot sight anyway, and that will correct any sighting problems one may have with this Airlift Rifle. The FPS is I would say about perfect for most Airsoft shooting conditions and it can be used with the pre-installed spring either for CQB or out door games. I do like the 120 round magazines as there is no need to whined a spring half way through a magazine but you will need more magazines on hand or a good speed loader handy for an Airsoft Battle. Just keep in mind your battery options will be limited due to the battery area being rather small since this very compact AIrsoft Rifle does have limited space to put a battery.
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model:Edge SA-X01 Materials: Mostly metal/aluminum. Weight: 5.52 pounds ( 2.50 kg). Total Length: 23.5-27 inches (597-686mm). Barrel: 10.63 inch (270) inner 6.03mm tight bore barrel non rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 380 round magazines. FPS: 380 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on the Specna Arms Edge SA-X01 AEG Airsoft Rifle is fairly shot and light, it is basically a simple off off switch as it is not mechanical but rather electric. For this reason there is no real creep or feel of a release. When you get to a point in the trigger you close a circuit that activates the electors motor cycling the spring.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms Edge SA-X01 AEG Airsoft Rifle, I am planning to make a video for this rifle next week if all goes well. I have reviewed other Specna Ames Core products in the past and made Field test Videos for them so perhaps check one of those videos out in the time being for a bit of a heads up of what you can expect from the Specna Arms Core SA-J73 AEG Airsoft Rifle.
Build Quality: Specna Arms Airsoft Rifles are made of good quality no matter if you go with the Core or Edge versions. You will still get a quality product with quality materials and metal parts where you need them. The Edge Series offers upgrades like more metal parts, improved gearboxes and electronics along with additional accessories but you pay a bit rmeo for the added quality and add ons.
Realism: The Specna Arms Edge SA-X01 AEG Airsoft Rifle is based on the AR15 or M16 platform of course in a very modern compact PDW styled. It looks and feels the part for sure with lots of working parts including the safety, selector switch, charging handle, dust cover, adjustable rear stock, pop-up front and rear sights as you would expect. Most of the hardware should be interchangeable with a real steel AR if you want to personalize the look of your Specna Arms Rifle.
Pros:
Very high quality product with quality components throughout (Already listed in Specifications).
4 positions rear stock.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Almost all metal build.
Removable fully adjustable pop-up sights.
No orange tips on our Canada Store versions.
Lots of rial mounting options using M-LOK System..
Comes with a fore grip and deans connector and two magazines.
Easy access to motor for any possible trouble shooting you any need to do.
I love the compact size. perfect for close closer quarters situations.
Cons:
Much higher cost than Core Series.
Magazine capacity is low but comes with two magazine.
You will need a very specific compact battery setup for this Specna Arms model.
Comments:
I for sure like the look of the Specna Arms Edge SA-X01 AEG Airsoft Rifle, but more than that you get a really great Compact PDW Airsoft Rifle at a reasonable price with a ton of quality components and a mostly all metal build. Specna Arms even includes an additional magazine in the box. You could go with one of their Core series of Airsoft Rifles in a similar PDW and save a bit of money but if you can afford the upgrade then I would go for this version as you will not need to upgrade it in the future and that alone will save you some money over time. I would suggest adding a couple Lipo batters and a good charger to your shopping cart and maybe even an couple more magazines.
My Vimeo Table Top Review for the Specna Arms Edge SA-X01 AEG Airsoft Rifle:
Type: AEG Airsoft Rifles Manufacturer:Specna Arms. Model:Core SA-J73 Materials: Fiberglass reenforced plastic and metal/aluminum. Weight: 5.7 pounds (2.59 kg). Total Length: 23.4 - 32.6 inches (594 - 828mm). Barrel: 15.7 inch (399mm) inner 6.03mm tight bore barrel non-rifled. Propulsion: AEG. Action: Single action semi & full auto. Ammunition Type: .6mm plastic Airsoft BB’s. Ammunition Capacity: High cap 430 round magazine. FPS: 370-380 fps with installed spring, included M90 spring will be lower fps.
Trigger Pull: The trigger pull on the Specna Arms Core SA-J73 AEG Airsoft Rifle is similar to a light single action trigger as essentially the trigger is non-mechanical, but rather it is more like an electrical on off switch. There is a little bit of take up with virtually no extra friction to let you know when the release is, with a bit of use you will figure out exactly when the trigger will release the action.
Accuracy: At this time I have not made my Field Test Shooting Video or even shot the Specna Arms Core SA-J73 AEG Airsoft Rifle, I am planning to make this video for next week if all goes well. I have reviewed other Specna Ames Core products in the past and made Field test Videos for them so perhaps check one of those videos out in the time being for a bit of a heads up of what you can expect from the Specna Arms Core SA-J73 AEG Airsoft Rifle.
Build Quality: One thing I can say, is no matter if you get the Core or Edge version of the Specna Arms AEG Air Rifles, you are getting extremely good value for your money, and neither one is going to have any low quality parts in it. Even the lower cost Core Series will have fiber glass reenforced plastic and metal parts along with a metal gearbox and virtually almost the same build as the more premium and higher priced Edge Series. You will get upgrades in the Edge Series like an aluminum receiver and buffer tube, a GATE X-ASR Mosfet, upgraded Gearboes, and an additional magazine.
Realism: The Specna Arms Core SA-J73 AEG Airsoft Rifle is based on the AK platform with a bit of a more modern look to it which includes a synthetic folding stock, a sight mounting system and a more modern magazine design. The Specna Arms Core SA-J73 AEG has lots of metal parts in it and has a good overall weight and feel to it which make is not too heavy or too light in my opinion. Our Canada version even come with a black flash hider rather than orange one which helps with realism.
Pros:
Very affordable price ($200 at time of video), yet very high quality product for what you pay.
Quality components throughout both the Core and Edge series.
Precision barrel internal 6.03mm diameter.
ESA™ quick spring change system makes spring changes quick and easy.
Comes with two springs for potential indoor and outdoor usage.
Plastic parts are fiberglass reenforced making them very durable.
Rear sight is adjustable on the fly for elevation.
No orange tips on our Canada Store versions.
Side mounting option for an optical or red dot sight system.
Metal V3 Gearboxes with metal gears and mostly all metal parts inside.
Decent amount of space for a battery.
Weight is about perfect, may actually too heavy with metal receiver?
Cons:
Plastic receiver.
Need to remove dust cover and use a screwdriver to adjust the hop-up.
No battery or charger included.
Comments:
The Specna Arms Core SA-J73 AEG Airsoft Rifle for right around $200 is not what I would expect for such a lower priced more entry level Airsoft Rifle. The build quality and components in this Airsoft Rifle are not budget by any means and when you hold it, it feels like a very high quality product. Sure you don’t get a battery or charger with it which you often find bundled with lower cost Airsoft Rifles, but generally these batteries and chargers are extremely entry level and will require upgrading almost immediately. So do yourself a favor and invest in a good battery setup if you do not already have one. If you’re in the market for an AK based AEG Airsoft Rifle and have a limited budget but still want a decent product, then I would recommend the Specna Arms Core SA-J73 AEG Airsoft Rifle for sure.
My Vimeo Table Top Review for the Specna Arms Core SA-C07-PDW AEG Airsoft Rifle:
In this performance Field Test Shooting Video for the John Wayne Marshal CO2 BB Revolver, I test out what the fps velocity is using a fresh standard 12 gram CO2 cartridge and shooting 4.5mm Steel BB’s through my Chronograph. I then setup a paper target 30 feet down range and shoot 10 rounds into it using the Single Action Only Trigger to see how tight of a grouping I can get out of the box. If you have not already watched my Table Top Video Review for the John Wayne Marshal CO2 BB Revolver, then make sure to do so for details and specifications along with some nice close up video.
First up for my velocity fps test of the John Wayne Marshal CO2 BB Revolver, I shot 5 rounds through my Chronograph. The slowest fps was 354 and the fastest shot hit an fps of 368, this result averaged 358 fps which was a somewhat under the claimed “up to” 420 fps from AirVenturi, still an OK velocity for shooting pop cans and the likes up to 30-40 feet away. The temperature in the Sea Can was about 20 degrees Celsius which is around 68 degrees Fahrenheit, so a good temperature to get middle of the road performance from a CO2 Airgun like the John Wayne Marshal CO2 BB Revolver. In warmer temperatures you can expect higher velocities…
I then placed my paper target on my pellet trap 30 feet downrange and using my standard semi rested shooting position (hands rested on a sandbag up front and sitting on a stool in the back), I proceeded to shoot 10 rounds into the target with the John Wayne Marshal CO2 BB Revolver and I was able to get about a 4 inch grouping well centered up and down but pushed to the left about 3 inches. I am not sure why this shot grouping spread out so much for me as my Crosman Forty Filed Test Review gave me a much better grouping and these guns are literally the same gun with different branding being the only real differences. Maybe I was just off on this day? Hey it happens sometimes!
The John Wayne Marshal CO2 BB Revolver is a lower cost mostly plastic Single Action Army Revolver with a fair amount of plastic in the build, but it does feel fairly well built and fairly solid other than being a bit lighter weight. It should produce close to 400 fps velocities in warmer conditions which is more than enough for plinking and pop can shooting which is really what it is built for. I do have to mention that this John Wayne Marshal CO2 BB Revolver for whatever reason is double the price of the Crosman Fortify CO2 BB Revolver I reviewed earlier, so if you don’t care about the John Wayne Licensing, than maybe consider the Crosman version for a lower priced option.
In this Filed Test Shooting Video recorded in the Replica Airguns Indoor Sea Can Shooting Range, I test out the Gamo GP-20 Combat CO2 BB Pistol to see what the actual velocity is in fps shooting 4.5mm steel BB’s with a fresh CO2 Cartridge. I also shoot 10 rounds of BB’s into a paper target setup 30 feet down range to see just how accurate the accurate the Gamo GP-20 Combat Pistol is out of the box. If you are more interested in details and specifications along with some closer up video of the Gamo GP-20 Combat CO2 BB Pistol, then make sure to watch my Table Top Video for it located here.
So let’s get to the velocity test for the Gamo GP-20 Combat CO2 BB Pistol. Gamo does claim up to 400 fps and to find out if these claims are true, I first installed a brand new 12 gram CO2 cartridge in the Gamo GP-20 Combat CO2 BB Pistol and proceeded to shoot 5 rounds through my Chronograph. I then averaged the shots out and was impressed with a much higher than claimed velocity of 422 fps. My slowest recorded shot was 419 fps with the fastest shot hitting 424 fps, so all of them very close to each other.
Moving on to the accuracy portion of my Field Test, I then setup a brand new paper target 30 feet away and using a semi rested shooting position (Hands on a sand bag up front and sitting on a stool in the back), I purposely shot 10 rounds with care into the target. The Gamo GP-20 Combat CO2 BB Pistol does not have adjustable sights at all so you will have to adjust your aim point if it is not bang on out of the box for you. That said, for me I was able to get about a 3 inch 10 round shot grouping, fairly well centered but just a bit to the left, about an inch or so. The shots did spread out a bit more up and down with less of a spread left to right, but still a decent grouping none the less.
The Gamo GP-20 Combat CO2 BB Pistol is like many of these low cost CO2 NBB BB Pistols, was very predictable as I have shot a ton of them and since they all share similar mechanical attributes internally, they tend to shoot about the same. I don’t mean this as a bad thing since they generally all shoot fairly decent with right around 400 fps velocities and generally I get anywhere from a 2 inch to 4 inch grouping with them. The good parts is the design is tried and trued and seems to be very durable and problem free with less moving parts to go wrong. They are also rather low cost and the magazines are interchangeable, so if you have other models based on this same build design, then you can mix and mach your magazines and load them all up for non-stop shooting fun. I do like the overall feel of this NBB CO2 BB Pistol, and the sights are very easy to aim with being white dot in the front and fiber optic in the back. If you are looking for a low cost basic NBB CO2 BB Shooter then this could just check all those boxes for you.
Type: BB Pistol. Manufacturer: Distributed by AirVenturi. Model: John Wayne Marshal. Materials: Mostly plastic, some internal metal parts. Weight: 1 pound (455 grams). Total Length: 10.5 inches (26.6cm). Barrel: 5.55 inches 14cm) metal non-rifled. Propulsion: CO2. Action: Revolver SAO. Ammunition Type: 4.5mm Steel BB’s. Ammunition Capacity: 18 round internal magazine. FPS: Claimed 420.
Trigger Pull: The trigger pull on the John Wayne Marshal CO2 BB Revolver is a single action only trigger, so you will have to cock the hammer back with each shot which does take away most of the trigger pull length and weight, making the Marshal trigger short and light and easy to shoot. Ideal for slowed down accurate shot placement, but less effective as an action shooter unless you have a very quick thumb!
Accuracy: I have not tested out the John Wayne Marshal CO2 BB Revolver but it should perform exactly like the Crosman Fortify revolver as they are literally the exact same gun with the exception of the branding and licensing. In my Field Test Shooting Review for the Crosman Fortify CO2 BB Revolver it did shoot a little bit lower than the claimed 420 fps and shot around a 2 inch 10 shot grouping at a target setup 30 feet away. You can watch that video here but I will be making a dedicated Field Test Shooting Video for the John Wayne Marshal CO2 BB Revolver shortly…
Build Quality: When it comes to the build for the John Wayne Marshal CO2 BB Revolver, there is not a lot to get overly excited about. It is basically a mostly all plastic gun with some metal parts internally like the barrel, trigger, hammer and CO2 area. The John Wayne Marshal has that lower cost Airgun, two halves, screwed together build which generally looks better on the side without the screws showing. As it is mostly plastic it is on the light side at around just over a pound. Overall there are not a lot of moving parts so it should be reliable enough just for that reason alone. All the mechanical components do what they need to do and feel solid enough.
Realism: The John Wayne Marshal CO2 BB Revolver at a glance looks a lot like a Colt Single Action Army Revolver, it has the same shape and size but the weight is much less at about half. The lack of actual bullet holes in the cylinder looking from the front of the revolver does take away from its realism. I guess I am really used to the new generation revolvers with working cylinders and real loadable and removable shells, but these guns are more expensive and hold less ammo as they are genuine to the 6 shooter capacity.
Pros:
A decent looking replica of a Colt Single Action Army revolver.
Single action only trigger is short and light and well suited to careful shot placement shooting.
420 claimed fps is about perfect for plinking at ranges up 30-40 feet.
18 round magazine has a nice high capacity and easy to load when empty
Safety is well thought out and built into an already existing part of the gun rather than simply adding a switch afterwards.
I like the look with the all back frame and bone white grips.
CO2 Allen key is built into grip so you always have it on hand and will not lose it.
John Wayne licensed for those old west John Wayne fans.
Cons:
Mostly plastic builds makes it a bit light in the hand.
No fake shell holes in the front of the cylinder, could have added this for a more genuine look.
Twice the price of the Crosman Fortify which is basically the same Airgun.
Comments: The John Wayne Marshal CO2 BB Revolver is for sure an option if you are looking for an old west single action cowboy BB shooter and specifically if you are a John Wayne fan. If you don't care about the John Wayne licensing and want to save about half of the price then my recommendation is to go for the Crosman Fortify as it is the same exact CO2 BB Revolver at the end of the day minus the john Wayne licensing on it. You also have the option of buying one of the many Shell Loading Single Action Army Revolvers available but they are a bit more money and will shoot a little slower with less ammo capacity but the trade of is a lot more realism.
Type: NBB CO2 BB Pistol. Manufacturer: Distributed by Gamo. Model: P-20. Materials: Plastic & metal. Weight: .97 pounds (439 grams). Total Length: 7.25 inches (184mm) Barrel: 4.25 inches (108mm) metal non-rifled. Propulsion: CO2 x 1. Action: Semi auto NBB, double action only trigger. AmmunitionType: 4.5mm steel BB's. AmmunitionCapacity: 20 round metal stick magazine. FPS: Claimed 400.
Trigger Pull: The trigger pull on the Gamo GP-20 Combat CO2 BB Pistol is the same as pretty much all of the DOA trigger low cost BB Pistols where the trigger has to do all the work. Much of which is pulling back the fairly strong internal hammer spring which in this case is the barrel which protrudes slightly out of the front of the pistol until you reach the release point, and it snaps back hitting the valve and pressurizing the Airgun. This will give you a bit of a finger workout if you are shooting fast and want to empty out the 20 round magazine.
Accuracy: At this point I have not tested or shot the Gamo GP-20 Combat CO2 BB Pistol but I plan on making my Field Test Shooting Video the following week so stay posted for that. I do expect it to perform nearly exactly live every other Airgun made like this, and there are many that essentially have all the same internal components with a slightly redesigned outer shell, so mechanically they are all the same and should shoot about the same. It should get really close to the claimed 400 fps and I expect it to shoot under a 2-3 inch grouping, unless I am having an off day.
Build Quality: The build quality of the Gamo GP-20 Combat CO2 BB Pistol is what you expect from almost all plastic BB Guns of this type. It is not super heavy but that means less can break when dropped on a hard surface. Fit and finish are good and one gripe I have with most of these types of BB pistols built the same way, is that the grips are a bit lose so it can pop off when you pull it back. The Gamo GP-20 Combat’s grips are a lot more solid and this does help make the Airgun feel a bit more confidence inspiring.
Realism: The Gamo GP-20 Combat CO2 BB Pistol from what I can see is not an exact copy of a real steel pistol in production but it does look like a modern semi auto pistol in design. The barrel is slightly recessed, and the CO2 tab is also hidden inside the grips, so unless you get close to the pistol you would think it could be the real deal. That said some giveaways are the moulded into the slide ejection port and the screw holes on the right side of the two plastic halves of the Airgun along with the kind of out of place standard safety switch that looks more like something you would find on a piece of electronics.
Pros:
Very low cost and simple design will make it reliable.
Fit and finish looks decent for an all plastic gun, grip are actually pretty tight.
Picatinny rail for adding accessories like a laser or tac light.
Standard metal stick magazine found in lots of Airguns for cross compatibility.
Right hand screws are very small and less obvious then some other two sided low cost plastic Airguns.
White dot sight up front and fiber optic in the back are easy to see on all backgrounds..
Safety is right above the trigger finger so easy to switch if you are right handed.
Recessed barrel for added realism.
Cons:
Some more metal would have been nice, but typical of a low cost BB shooter like this.
Double action trigger does require some work, so action shooting will be a bit harder.
Not a lot of working parts other than the trigger, safety, and magazine release.
Comments:
I have reviewed many CO2 BB Pistols built exactly like the Gamo GP-20 Combat CO2 BB Pistol, so it is at least for me, not the most exciting Airgun review but I always enjoy the chance to shoot even the most basic of Airguns. I would say the Gamo GP-20 Combat CO2 BB Pistol in this category is one of the nicer options as I feel Gamo stepped up the build quality just a bit, even if it was just to make the grips feel more solid and less prone to popping off when loading CO2. It is a little bit beefier than similar CO2 BB Pistols in this category so maybe not the best for smaller handed individuals but good for someone like me with larger mitts. The price is right for sure and with its simple design, it should perform as expected for a good long time!
Another box showed up at my door and this time I had no idea what was inside it, I asked the boys in the warehouse to surprise me and send some new product as I was low on review items, and in a couple of days later this tall somewhat large box showed up. In this Replica Airguns June Mystery Box Unboxing Video I open the box and take a look at what’s inside. I recommend you just watch the video and enjoy the suspense with me, but if you want to cheat and find out now, then look below at quick breakdown of each item…
What you can expect from this Field test Shooting Video for the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle are two things for sure. I test out the velocity with both 4.5mm Steel BB’s and .177 caliber lead pellets, I also chuck both of these rounds downrange to see if one may be more accurate than the other and how close I can get a 5 shot grouping for each ammunition type. If you are looking for details and specifications and perhaps some more close up video of the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle then you may want to watch my Table Top Video for it here.
If you have watched any of my hundreds of Field Test Videos, then you already know I start off shooting 5 or so rounds through my Chronograph to see what the average velocity is going to be. In this Field Test I shoot 3 rounds of each ammo type, 3 BB’s and 3 pellets since it is a pump Airgun and they tend to be more consistent than a CO2 Airgun. Barra claims around 350 fps, I am not sure if this is for BB’s or Pellets or both? As it turns out (spoiler alert), both ammo types performed about the same in both the velocity and accuracy portion of my testing. For BB’s, my chronograph testing got 303, 316 and 316 for an average of 312 fps. For pellets my chronograph results were 309, 309, 314 for an average of 311, so only 1 fps off between the two. Keep in mind the BB’s weigh around 5.1 grain while the pellets I was using were around 7 grain, so the pellets will be carrying more energy downrange and hit a bit harder. By the way they are also harder to load so I would suggest just shooting the steel BB’s in this one since you can keep the fun times flowing better...
Next up for my accuracy test of the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle, I again shot both ammo types, but 5 rounds of each and just like the velocity test they matched each other almost exactly. Both the steel BB’s and lead pellets I was using shot really well centered left to right, maybe just a hair to the left and both shot just about an inch or so high on the bullseye I was aiming at 30 feet away. The 5 BB’s grouped nicely for me at about an inch while the pellets did get a slightly tighter 3/4 inch grouping for me in this test. I was using a semi rested shooting position sitting on a stool in the back with the rifle rested on a sand bag up front.
The Barra 1866 Junior Dual Ammo Pump Cowboy Rifle really surprised me in how it performed, It’s not going to be the most powerful BB/pellet cowboy rifle out there but compared to a Red Ryder it does have a bit more punch and in terms of accuracy I found it shot better for me than at least I can do with a Red Ryder type BB rifle. You also have the option of shooting BB’s or Pellets but I would recommend shooting BB’s since you have that 50 round hopper and the BB’s auto load when you pull the bolt back which is much easier than loading pellets with a pair of tweezers which is what I needed to do to get them in with my sausage fingers. One more thing to mention is I do not recommend pumping this air rifle more than 1 time, not only does the manual say not to, but there is little benefit in pumping it more times with only the risk to damaging the airgun. I pumped it 4 times and only got about 20 fps more out of it so just don’t do it. If you want a Cowboy style Air Rifle with a little more realism than say a Red Ryder but that shoots about the same then checkout the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle.
Type: Lever/Pump Dual Ammo Rifle Manufacturer: Distributed by Barra. Model:Junior Dual Ammo Pump Cowboy Rifle. Materials: Mostly plastic, some metal. Weight: 4.1 pounds (1859 grams). Total Length: 36 inches (91.44mm). Barrel: 18 inches (45.7cm) metal rifled. Propulsion: Pump Compressed Air. Action: Lever/Pump Ammunition Type: .4.5mm steel BB’s & .177 Caliber Pellets. Ammunition Capacity: 50 BB’s in hopper, single shot Pellets. FPS: Claimed 350-400.
Trigger Pull: The trigger pull on Barra 1866 Junior Dual Ammo Pump Cowboy Rifle is respectable at about 5 pounds with a medium to short pull length. I would say it is perfect for novice shooters as it is not overly light so as not to go off easily by accident and not too heavy for youth shooters with less finger strength than adults. When you pull the bolt back to reload the ammo, the internal cocking mechanism is activated allowing for single action type shooting. You do need to activate the bolt with each shot.
Accuracy: My dedicated field test shooting video is planned for this week, so for now I have no idea what to expect in terms of velocity and accuracy from the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle, other than it is claimed to shoot around 350 fps when using pellets. It does have an 18 inch rifles barrel which should contribute to helping a lot with accuracy, so I do have high expectations especially since it has a pretty good trigger and when looking down the sights they allow for a nice tight fix on the target. The rear stock is short but not so short that it feels cramped for an adult shooter which should also help when I perform my accuracy test.
Build Quality: The Barra 1866 Junior Dual Ammo Pump Cowboy Rifle is nothing special when it comes to materials being used in it. It is for the most plastic with the exception of the inner and outer barrel along with the rear sight and I would imagine some other internal parts. It does feel not so bad as it is a bit over 4 pounds and is smaller in nature so it feels solid enough in the hand. I wish the Pump/Lever was metal as it would of felt a bit more solid and would have added a bit more additional weight to the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle. Fit and finish is good and overall the gun looks and feels good.
Realism: The Barra 1866 Junior Dual Ammo Pump Cowboy Rifle is essentially styled after the Old West Lever Action Cowboy Rifle, and it has everything we would expect other than loading shells which is available in other Lever Action Air Rifles if you don’t mind paying a premium for one. The lever is actually not a lever but more of a pump so the action and look of the lever is not exactly as you would expect from a true lever action rifle, but when it is locked in place it does look the part. The gold receiver and rifle band looks sharp and I feel matches up with the dark imitation wood stock nicely. One point to make is that the hammer is not the hammer but actually the safety and the bolt not only opens the breach area but also acts as the cocking mechanism for the internal hammer.
Pros:
Super easy to pump.
Fit and finish looks decent for a mostly plastic airgun.
In terms of realism it does look like a more compact lever action rifle for the most part
Can shoot either BB’s or Pellets.
Holds 50 BB’s in the hoper for quicker follow up shooting.
Metal octagon outer barrel adds addition weight to a mostly plastic gun.
Rear sight is metal and is also adjustable for elevation.
Trigger pull is pretty decent, not too light but is short and about 5 pounds.
Recessed barrel for added realism.
Made for kids but the shoulder pull length and sight placement works for adults too.
The gold receiver looks good and gives it a unique look.
Cons:
Mostly plastic build.
Manual says only one pump but I wonder why this is the case or perhaps just to deregulate it?
Pellets are hard to load especially if you have larger hands and fingers.
Comments:
The Barra 1866 Junior Dual Ammo Pump Cowboy Rifle is a competitor for products like the Red Ryder but it has a bit more realism in terms of looking more like a replica of a real steel Lever Action Cowboy Rifle. It also allows for shooting pellets and has an actual rifled barrel so hopefully this helps with accuracy. You can still kind of shoot it Lever Action Style when shooting BB’s but there is the addition of charging the bolt with each shot over and above working the Lever / Pump, so it will take a bit more time to get those follow up shots as compared to a Red Ryder BB Rifle. One other point to make is that the lever is actually not a lever but more of a pump since this is not spring powered but instead has an air reservoir which on this version only allows for one pump, but on the non-junior version you can pump it up to 10 times and get a claimed 800 fps out of it (US Version). I am going to try pumpkin the Barra 1866 Junior Dual Ammo Pump Cowboy Rifle up to three times to see if there is any difference in power but this could void your warranty if you damage the air reservoir by over pressuring it. So be good and only pump yours once as instructed in the manual.
