Type:Airsoft Rifle. Manufacturer: Acturus. Model: AK05. Materials: Mostly all Metal. Weight: 8.2 pounds (3.7 kilograms). Length: 31.1 inches (790mm) Barrel Length: 11 inch (280mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Acturus AK05 AK AEG Airsoft Rifle like other AEG Rifles is not mechanical as it is essentially electrical driven so basically it is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed the Acturus AK05 AK AEG Airsoft Rifle or even tried it out yet. I hope to get to my Field Test Shooting Video for the AK05 later next week, until then we can assume it will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper work it comes with claims around 390+fps.
Build Quality: The Acturus AK05 AK AEG Airsoft Rifle is almost all metal in design with from what I can tell only the pistol grip being plastic. The receiver and top dust cover are both hardened steel with the receiver made out of stamped steel just like areal AK. The AK05 is nice and heavy for its size and the fit and finishes is very good all around. Internal parts are all of high quality too.
Realism: The Acturus AK05 AK AEG Airsoft Rifle is based on the AK platform with this version being a more compact and tactical model. Externally it looks the part for sure, holding it in your hands it feels the part too. As expected the insides are all Airsoft but you would need ot take the dust cover off or pull back the charging handle to figure this out. Again the Acturus AK05 AK AEG Airsoft Rifle is an almost all metal Airsoft Gun with an actual stamped steel receiver and steel dust cover, it’s hard to get much more realistic looking and feeling than that.
Pros:
Lots of mounting options: Picatinny rails, M-LOK, AK Side Rail.
Semi and full auto adjustable.
5 position adjustable rear stock.
Mostly metal construction and lots of actual steel including the receiver and dust cover.
Lots of weight to it at 8.2 pounds, feels awesome to hold.
Comes with two magazines, one Hi Cap and one Mid Cap.
Comes with a secondary all black squared off flash hider.
On the fly adjustable rear sight for elevation.
Quick change spring system.
Easy to get to and adjust rotary hop-up adjustment.
Should be good for longer range shooting with nice high claimed fps.
Cons:
Will need a very specific battery type, thin and long.
Rear sight only adjustable for windage and not elevation.
May even be a bit heavy for all day use.
Comments:
The Acturus AK05 AK AEG Airsoft Rifle along with the other Acturus AK Airsoft Rifles is in my opinion one of the nicest AEG AK based Airsoft rifles you can get, at least in the mid price ranges. Being all metal with actual stamped steel parts really makes the AK05 feel realistic and of high quality. If you’re looking for something with a bit more heft than the Acturus AK06 that has a more useful rear stock at least in terms of adjustability and don’t mind giving up some of the compact features of the AK06 then perhaps the AK05 is more for you. IN my opinion the Acturus AK05 AK AEG Airsoft Rifle is a great combination of quality, size and features, hopefully my upcoming Field Test Shooting Review backs up the performance aspect and we can add that to the list.
My Table Top Video of the Acturus AK05 AK AEG Airsoft Rifle:
Type:Airsoft Rifle. Manufacturer: Acturus. Model: AK06. Materials: Mostly all Metal. Weight: 6 pounds (2.7 kilograms). Length: Folded/unfolded 18.9/27.4 inches (480/695mm) Barrel Length: 9.8 inch (250mm) inner 6.02mm tight bore non rifled. Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto SAO. Ammunition Type: 6mm Airsoft BB's. Ammunition Capacity: Hi Cap/Mid Cap - 550/135 FPS: 380-400fps.
Trigger Pull: The trigger pull on the Acturus AK06 AK AEG Airsoft Rifle like other AEG Rifles is not mechanical as it is essentially electrical driven so basically it is an on/off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back. Once the spring is fully drawn back it releases and compresses the air which then propelled the 6mm Airsoft BB. The higher voltage battery you use like an 11.1 volt will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire which in this rifle is very noticeable.
Accuracy: I have not Field Test Reviewed the Acturus AK06 AK AEG Airsoft Rifle or even tried it out yet. I hope to get to my Field Test Shooting Video for the AK06 later next week, until then we can assume it will shoot similar to most other AEG rifles with tighter bore barrels. I am expecting at least a 2 inch grouping at 30 feet down range in semi auto. In terms of velocity the test paper work it comes with claims around 370fps.
Build Quality: The Acturus AK06 AK AEG Airsoft Rifle is almost all metal in design with from what I can tell only the pistol grip being plastic. The receiver and top dust cover are both hardened steel with the receiver made out of stamped steel just like areal AK. The AK06 is nice and heavy for its size and the fit and finishes is very good all around. Internal parts are all of high quality too.
Realism: The Acturus AK06 AK AEG Airsoft Rifle is based on the AK platform with this version being a more compact and tactical model. Externally it looks the part for sure, holding it in your hands it feels the part too. As expected the insides are all Airsoft but you would need ot take the dust cover off or pull back the charging handle to figure this out. Again the Acturus AK06 AK AEG Airsoft Rifle is an almost all metal Airsoft Gun with an actual stamped steel receiver and steel dust cover, it’s hard to get much more realistic looking and feeling than that.
Pros:
Lots of mounting options: Picatinny rails, M-LOK, AK/SVD Side Rail.
Semi and full auto selectable.
All metal folding rear stock.
Mostly metal construction and lots of actual steel including the receiver and dust cover.
Lots of weight to it at 6 pounds, feels awesome to hold.
Comes with two magazines, one Hi Cap and one Mid Cap.
Comes with a secondary all black squared off flash hider.
Super compact design.
Quick change spring system.
Easy to get to and adjust rotary hop-up adjustment.
Should be good for longer range shooting with nice high claimed fps.
Cons:
Will need a very specific battery type, thin and long.
Sights are non adjustable.
Folding type rear stock not adjustable for pull length.
Comments:
The Acturus AK06 AK AEG Airsoft Rifle along with the other Acturus AK Airsoft Rifles is in my opinion one of the nicest AEG AK based Airsoft rifles you can get, at least in the mid price ranges. Being all metal with actual stamped steel parts really makes the AK06 feel realistic and of high quality. I also like the compact tactical features of the Acturus AK06 AK AEG Airsoft Rifle making it easy to put in a backpack but not too heavy to lug around all day long. The Acturus AK06 AK AEG Airsoft Rifle also has a decent velocity and fairly fast rate of fire especially when using a higher voltage battery so you can expect excellent performance even from such a small compact AEG Airsoft Rifle.
My Table Top Video of the Acturus AK06 AK AEG Airsoft Rifle:
In this Preview Unboxing Video I Take a look at 4 new Airsoft products from Arcturus all of them being AEG Airsoft Rifles with two based on the AK platform and the other two based on the AR platform. Three of the AEG Airsoft Rifles are mostly metal while I also feature a lower cost version with a Nylon Fiber Polymer receiver. All of these Replica AEG Airsoft Rifles are very good quality but you will get all metal (mostly steel and aluminum) build and a Hi-Cap and Mid-Cap magazine with the higher cost versions.
This review shows that low cost Airguns can perform just like higher priced Airguns. They may not be as realistic and all made out of metals for that added weight and feel but in terms of power and accuracy they can still get the job done as is with the Umarex NXG CO2 BB Pump Shotgun! In this Field Test Shooting Review I do just that, I test the power and accuracy first by shooting 5 rounds through my Chronograph to find out what the real world fps is, I then I shot 10 rounds down range at a fresh paper target to see what kind of grouping I can get and if the Umarex NXG CO2 BB Pump Shotgun is sighted in on the target out of the box.
Starting with the velocity test I first placed a brand new 12 gram CO2 into the Umarex NXG CO2 BB Pump Shotgun and loaded up the 10 rounds rotary magazine with Daisy Zinc Coated 4.5 mm Steel BB’s. The temperature was around 22 degrees Celsius which is 72 degrees Fahrenheit in the sea can indoor shooting range so not too warm or cold. The claimed fps from Umarex is 450, I was able to get an average of 403fps with the fastest shot hitting 425fps and the slowest shooting down to 388fps. So a bit under the Umarex claimed velocity but in the ball park.
Next I performed the accuracy test for the Umarex NXG CO2 BB Pump Shotgun and since the sights are non adjustable you kind of hope that where you aim is where the shots go but if they don’t then you will need to adjust your aim point just a bit. Out of the box the Umarex NXG CO2 BB Pump Shotgun did shoot a bit low but was fairly bang on side to side so when shooting at around 30 feet out you will need to aim just a tad over the intended target. Out of 10 shots, 8 rounds where all within a nice 1.5 inch grouping with a couple of flyers that I kind of want to keep out of this test because it was probably more me than the gun causing them to go off a bit. 1.5 inches is very good for a 4.5mm Steel BB Airgun!
All in all the Umarex NXG CO2 BB Pump Shotgun shot right around 400fps which is for sure a step up for something like a Red Ryder BB Rifle that at best can shoot 300fps. You also don’t have to work the pump as hard as you would the lever on a Red Ryder since the Umarex NXG CO2 BB Pump Shotgun is CO2 powered rather than spring powered. I also feel like the Umarex NXG Pump Shot was more accurate than the Red Ryder at least for me but that said some people can hit a nickel all day long with their Red Ryders! There are not a lot of Pump Action Looking Airguns out there in 4.5mm Steel BB versions and in more compact easier for younger or smaller shooters so if you fall into that category and want something in a shotgun format then the Umarex NXG CO2 BB Pump Shotgun may be perfect for you.
Trigger Pull: The trigger pull on the Umarex NXG CO2 BB Pump Shotgun is pretty decent, there is a short task up and fairly easy release as the pump action not only turns the rotary magazine but also cocks the internal hammer/striker system. So you will need to pump it before your first shot and after each shot.
Accuracy: I have not Field Test Reviewed the Umarex NXG CO2 BB Pump Shotgun yet but will be making a full Fields Test Review this week to find out what to expect in terms of accuracy and velocity. So we will find out if the fps is closer to the on the box specs of 450 fps or the mostly online specs of 490 fps. Perhaps somewhere in-between?
Build Quality: The Umarex NXG CO2 BB Pump Shotgun is almost all plastic which is not a bad thing in terms of quality and durability. The fact that it only weighs in at 2 pounds may make it feel kind of light and cheap but in a drop or fall situation it means it will most lily not sustain any damage because of the light weight. Most of todays airguns when made out of metals generally are made out of pot metal or zinc alloy which is a nice heavy metal that looks and feels great but is not super strong so when you drop a heavier gun made out of this material it can easily get damaged.
Realism: The Umarex NXG CO2 BB Pump Shotgun looks like a traditional pump action shotgun and even has a little bit of a recessed barrel to make it more believable but it is smaller in size since it is designed more for younger and smaller shooters. The light weight is not only a giveaway but makes ti feel more like a toy than a real gun. If you can ignore that then hopefully you can enjoy the Umarex NXG CO2 BB Pump Shotgun for what it is which is a low cost compact BB rifle made for customs interested in Airguns liek the Red Ryder but that perhaps want a bit more power.
Pros:
Low cost CO2 rifle great for all ages and sizes.
Has a fiber optic front sight.
Comes in a nice looking two tone Black/FDE color scheme.
Fairly easy to pump since the pumping action is not required to activate a spring or compress air.
Built in manual thumb safety.
Stock and high check rest position feel good and a good size length for smaller younger shooters.
Rotary drop out magazine holds 10 4.5mm steel BB’s for quick follow up shots.
Trigger feels pretty good, short and fairly light.
Full ambidextrous design.
Perhaps a step up for entry level shooter over a Red Ryder type BB rifle in terms of power.
Overall a decent looking air rifle.
Cons:
Mostly plastic, so a bit on the light weight side.
Sights are not adjustable in any way.
May be a bit cramped for larger shooters.
Comments: The Umarex NXG CO2 BB Pump Shotgun is not going to win any prizes for quality and realism but keep in mind it is really designed more for entry level younger shooters getting into the Airgun hobby. For them this will be not so intimidating as a larger, heavier more realistic version of a replica Shotgun. I think it will be realistic enough for most new Airgun Shooters and in terms of performance and features it is for sure a step up form something like a Red Ryder BB Rifle. I am looking forward to my upcoming Field Test Shooting Review out what the actual velocity is and what kind of groupings I can get shooting 30 feet down range on a paper target.
My Table Top Video of the Umarex NXG CO2 BB Pump Shotgun:
Umarex has released yet another Legends Replica Airgun and perhaps this one may be the most iconic yet, the M3 Grease gun with a history as far back as 1942. It was put into service int 1944 and then the later variant the M3A1 was used in the Korean War. Also make sure to watch my Table top Video for it for specifications and details along with more close up video.
Getting back to the Field Test Review for the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun, as always I like to test each gun out in the Replace Airguns Indoor Sea Can Airguns Range first placing 5 rounds through my Chronograph to find out the real world velocity of each test gun, then I shoot 10 rounds in semi auto at a distance of 30 feet onto a paper target to see how tight of a grouping I can get shooting from a seated and rested position. With full auto Airguns I like to then perform a full auto shooting test to see how it groups in full auto as often times the full auto grouping will open up somewhat as some Blowback Full Auto Airguns do tend to move around a lot more in full auto mode.
For my Power or Velocity test I was using dual brand new CO2 cartages. Umarex does state that the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun will shoot around 450 fps and with my 5 shot test I was able to confirm this and get close to this mark averaging 436fps. The temperature in the Sea Can was around 20 degrees Celsius or around 70 degrees Fahrenheit. Perhaps in warmer conditions I might hit the claimed 450 fps but I was close either way.
For my accuracy test I setup a new paper target 30 feet downrange and proceeded to place 10 shots into it using the peep sight on the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun. I was fairly pleased with a fairly tight 1.5 inch grouping in semi auto. I then switched over to full auto fun mode and with the remaining BB’s I unloaded 50 or so rounds in very short order and as expected the grouping opened up to closer to a 4 inch grouping. This was kind of expected since the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun uses an open bolt system which has a fairly heavy bolt which makes the blowback action more intense, similar to the KWC Mini Uzi but to a lessor degree.
Any time a company puts out another Full Auto Replica Rifle, especially full auto firing, I am 100% in on it. Both Crosman and Umarex have done a great job doing this and the Umarex Legends CO2 Blowback Full Auto M3 Grease Gun is another example of a well thought out and what I expect to be very popular Full Auto BB Rifle. Their Legends series encompasses guns of the later era which I personally really like since they are harder to come by in their real steel versions, so having them available in an easier to acquire version that you can even shoot in your back yard is a win win for everyone. I am also happy to confirm the high capacity double stack 60 round magazine seemed to feed pretty good for me only miss-feeding once during my testing while doing the Chronograph portion but it got back on track right away. If you’re into Full Auto Legendary Airguns then for sure pick one up from us!
In this Field Test Shooting Video I give the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol my usual Indoor Sea Can shooting field test using my Chronograph to see what the average 5 shot velocity is with .20 gram plastic Airsoft BB’s. I then shoot 10 rounds in semi auto at a paper target setup 30 feet down range using a seated shooting position with my hands rested on a sand bag up front for stability to find out what the accuracy is in semi auto mode. I follow this up with a full mag demo in full auto to see how large of a spread we get with this gun jumping around. If you want information on specifications and details along with some close up video of the Cybergun Licensed L6 .50AE Desert Eagle GBB Airsoft Pistolthen watch my Table Top Video for it here.
Starting off with my Chronograph test, the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol was able to get a 5 shot average of 392 fps with the fasters round hitting 400 fps and the slowest Airsoft BB recording 387 fps. Again I was using .20 gram Airsoft BB’s and the indoor temperature was around 20 degrees Celsius which is close to 70 degree Fahrenheit for reference so so the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol performed even better than the claimed on the box 380 fps.
Moving on to the accuracy portion of my Field Test Test for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol, I carefully placed 10 rounds into my fresh paper target and was a bit dissapoitned in the rather spread out group I got. I feel like this is because of the high fps and lighter choice of Airosft BB I used for this test. When shooting a gun with higher fps it is best to use heavier Airsoft BB’s at least when it comes to accuracy as they won’t get that beach ball effect of floating around so much. I did also shoot the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol in Full auto which does rock around a lot because of the heavy blowback recoil and as expected BB’s kind of went all over but if I was shooting at a human sized target from that range I am sure most rounds would have found their intended target.
Overall the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is a really nice Airsoft pistol. I love the way it looks and feels to hold in the hand and the blowback operation is very noticeable. It also shoots really hard for an Airsoft Pistol and other than the semi auto accuracy which may be corrected using heavier BB’s, it really does have a lot going for it. I may have to test it out again using heavier Airsoft BB’s to see if this improves accuracy for me at 30 feet out.
Trigger Pull: The trigger pull on the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is single action only which means you will need to rack the slide to not only draw the hammer back but to also chamber the first round. After that the blowback action will do this for you until you are out of ammo and then the slide will lock back. You can also manually draw the hammer back if a round is already chambered. The trigger itself is really nice, it’s light, super short with a crisp light release perfect for fast action shooting.
Accuracy: At this point I have not made my Field Test Shooting portion of my review for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol so I really don’t know what to expect? KWC claims an fps of 360 using CO2 as its power source and it is a realistic velocity based on previous Velocity tests with similar KWC Airsoft Guns. In terms of accuracy, again I have no idea since I have not reviewed this version of Desert Eagle before. So stay posted till next week when I make the Field Test Shooting Review for it.
Build Quality: Overall the metal and plastic build quality of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is good. It is mostly metal with a plastic frame, the real steel version would have an aluminum frame and has a weight closer to 4 pounds total so a bit lighter in terms of weight compared to the powder burning version. The fit and finishes look good.
Realism: The KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol is an excellent Replica Airsoft version of the real steel L6 Desert Eagle including the top and bottom rails and the ported front barrel. It also has full blowback action and you can fully field strip it. I like the addition of the fingered grips which I think adds ot the overall looks and function of this Airsoft Pistol.
Pros:
Lots of metal and good overall weight to it.
Very accurate replica of Desert Eagle L6.
Ergonomic rubberized grips.
Semi and full auto selectable.
Adjustable hop-up.
No orange tip.
CO2 for more power over GBB.
Uses standard KWC CO2 Desert Eagle magazines.
Picatinny rail top and bottom for lots of accessory mounting options.
Great light weight single action only trigger with super short take-up.
Cons:
Frame is plastic so compared to real steel version is much lighter.
Non adjustable sights, also all black so may be hard to see on darker targets.
No trademarks since non-licensed version via KWC direct.
Very large gun with large grips so not suitable for smaller handed shooters.
Comments: Going off just the looks and feel for the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol I can say for sure I do like it compared ot the standard KWC Desert Eagle with its venting up front and its ergonomic rubberized grips. I hope when I perform the Field Test Shooting Video fo fit it it performs well as the price point is good at around $200 Canadian and who doesn't want to have a Desert Eagle in their Replica Airgun collection at the end of the day!
My Table Top Video of the KWC DE L6 Desert Eagle CO2 Blowback Full Auto Airsoft Pistol:
Type:BB Rifle. Manufacturer: Umarex. Model: Legends M3 Grease Gun Materials: Mostly All Metal Construction. Weight: 7.7 pounds (3.5 kilograms). Length: 29.8 inches (757mm). Barrel Length: 8 inches (20 cm) smoothbore barrel. Propulsion: Dual CO2 Cartridge. Action: Semi & Full Auto Open Bolt Blowback Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 60 rounds. FPS: 460fps. Rate of Fire: 1050
Trigger Pull: The trigger pull on the Umarex Legends M3 Grease Gun is fairly light being a single action only trigger. You will have to open the bolt (pull it to the rear) which is located under the dust cover using your thumb but the recoil spring is not super heavy on the Airgun version. I would imagine this would take more effort on the real steel version.
Accuracy: I have not Field Test Reviewed the CO2 BB Full Auto Umarex Legends M3 Grease Gun as of yet but will be making a full Fields Test Review next week to find out what to expect in terms of accuracy on both semi and full auto modes along with velocity using brand new twin CO2 Cartridges.
Build Quality: The Umarex Legends BB Grease Gun is really made with form what I can see is an all metal construction at least on the outside. The fit and finishes feel and look really good and it has a nice balance and weight to it.
Realism: The Umarex Legends BB Firing M3 Grease Gun is based on the actual M3A1 version and looks just like it including the rough welds and simple build. Even the action is Open Bolt which means you have to pull the bolt back using your thumb or finger, then when you release the trigger the bolt moves forward loading a round in the chamber and then acting like the firing pin and firing the gun which in turn uses the pressure to cycle the bolt into the rear position ready to fire the next shot in either semi or full auto mode.
Pros:
Yet another Classic Legends Replica Airgun from Umarex.
Virtually all metal design with good overall weight.
Price is very reasonable for all metal replica machine gun in an all metal construction.
Semi and Full auto select-ability.
Dual CO2 design for increased shots and less cool down effect.
Super high capacity 60 round full size drop out metal magazine. (hopefully it works well)
Great looking replica of the real steel Grease Gun in looks, operation and feel.
Internal bolt blowback will give a bit of recoil feedback feel.
Uses a genuine open bolt system.
Recessed barrel for added realism.
Cons:
Sights are non-adjustable.
Hopefully high capacity magazine feeds consistently?
Selector switch under frame is not authentic but does allow for semi, full auto and safe modes.
Comments:
The Umarex Legends M3 Grease Gun is yet another great addition to not only the Legends Series of Umarex Airguns but also their Full Auto BB Rifle lineup! I am hoping the 60 round magazine feeds properly as double\ stack 4.5mm BB Rounds don’t always feed as well as Airsoft BB’s do. I guess we will find out when I make my Filed Test Shooting Video… That said the M3 Grease Gun is an excellent Replica of the real steel version with an all metal build and even a true to form open bolt blowback system. I really hope it performs well so I can recommend this Airgun, on first impressions and simply holding and looking around this BB Machine gun I am impressed so far.
My Table Top Video of the Umarex Legends Full Auto M3 Grease Gun:
In this Preview Unboxing Video I take a look at three new products just listed in our Replica Airguns Store. Two are products from Umarex both being CO2 4.5mm Steel BB and one is a CO2 powered KWC Blowback Airsoft Pistol. I don’t go into a ton of detail in this video but go over what is listed on the box and a quick walk around of each product.
First up I show off the KWC DE L6 CO2 Blowback Airsoft Pistol, it is much like the Cybergun Desert Eagle L6 I reviewed but without the orange tip and with notched pistol grips, also all back which is classic and looks great. This Blowback pistol shoots 6mm Airsoft BB’s at around 360 fps and has a full size dropout metal magazine that holds the CO2 along with 21 rounds.
Next I showcase a rather entry level 4.5mm CO2 BB Pump Action Rifle called the Umarex NXG Pump Shot that is a mostly plastic lighter weight build perfect for smaller or younger shooters. It uses CO2, shoots 4.5mm Steel BB’s and comes with a drop out 10 round rotary magazine. You will have to pump it before each shot but this makes the trigger fairly light.
Lastly but perhaps my favorite in this lineup I take a look at the CO2 4.5mm Blowback Umarex Legends M3 Grease Gun. Just like the real steel .45 caliber Grease Gun it is capable of full auto and also shoots in semi auto. You will find a full size drop out metal magazine that holds two CO2 cartridges along with 60 4.5mm steel BB’s. Thats a lot of rounds!
If you are wondering why I am doing another Field Test of a Crosman AR-15 type CO2 Full Auto BB Rifle… Well why not, any excuse to play around with one of these and I will take it. You never know, even though the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is essentially just a re-skinned R1, what if it performs better or worse than the standard R1. I better test it out and find out for myself.
Like all my other Field Test Shooting Videos I test out the Velocity and Accuracy in the Replica Airguns Indoors Sea Can Shooting Range where I can control the temperature, wind and lighting conditions. The goal is to see if the velocity is what the manufacturer claims and what kind of groupings I can get in this case shooting 10 rounds in semi auto and the rest in full auto.
Starting with my velocity test for the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle I shot five 4.5mm Steel BB’s through my Chronograph and was able to average 389 fps. Crosman claims a max fps of 430 which would be best case scenario in what would most likely be fairly warm shooting conditions. During my testing the temperature was not overly warm or cool, right around room temperature so around 20 degrees Celsius (70 ish degrees Fahrenheit) and I was using dual brand new CO2 Cartridges.
Next I tested out the accuracy for the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle first shooting 10 rounds in semi auto and then dumping the rest of the magazine in full auto. Right out of the box using the iron pop-up sights I was able to get all but 1 shot in the Bulls-eye which is about 1 inch in diameter so not only is the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle very accurate but it was really well centered out of the box in my case. Switching over to full auto the grouping spread out as expected more to around 2+ inches and placing a bit lower on the target but this is expected when shooting a blowback Airgun in full auto as it will move around a bit.
I do have to say the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is probably one of the best looking AR’s in the Crosman series of Full Auto BB Rifles and I am happy to report the performance was as expected since I have done several Field Test Shooting Reviews for this series of BB Rifles. No you do not get a red dot with the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle but rather more old school iron sights but it really suits this BB Machine Gun and for me it didn’t hurt performance at all!
In this Field Test Shooting Video I test out the BARRA 400e Full Auto AEG 4.5mm BB Rifle to test out the velocity along with the accuracy and also get an idea on what the rate of fire is in Full Auto mode as on the box it claims 550 rounds per minute using what I would assume is a 7.4 volt battery. I wanted to test the BARRA 400e using an 11.1 volt battery but mine died on me. I will more than likely make a short video where I test out the 11.1 volt battery to see how this effects the rate of fire. If you want more information on specifications and details for the BARRA 400e then check my Table Table Video for it here.
Starting with testing out the Velocity for the BARRA 400e Full Auto AEG 4.5mm BB Rifle I shoot 6 rounds through my Chronograph to average out the fps and I was able to average 385 fps which is fairly close to the claimed 410 fps. Temperature does not effect an AEG as no CO2 is being used. Battery voltage also does not effect velocity as long as there is enough voltage to make the AEG motor pull the spring all the way back. Only trigger delay and rounds per minute are effected by battery voltage.
Moving on to my accuracy findings, I loaded up a full 50 round magazine and first unloaded 10 rounds fairly quickly into my paper target setup 30 feet down range shooting from a seated shooting position with the BARRA 400e resting on a sand bag up front. I was impressed to get close to a 1 inch 10 round grouping that placed just a little to the left and down from the bullseye right out of the box. I could easily center the sights as they are fully adjustable. I then switched the BARRA 400e Full Auto AEG 4.5mm BB Rifle to full auto and shot the remaining 40 or so rounds into the same paper target and even though the grouping opened up a little bit, it was not by much so accuracy in semi and full auto is very good with the BARRA 400e.
I have to say the rate of fire on the BARRA 400e Full Auto AEG 4.5mm BB Rifle using a 7.4 volt battery is rather slow even compared to other Airsoft AEG Full Auto Airguns but I still yet have to test it out using a brand new 11.1 volt Lithium battery so I do expect the rate of fire to improve a noticeable amount. Stay posted for that update video. Even with the slower rate of fire from the BARRA 400e this gun is awesome, it is really accurate and the velocity stays super consistent since CO2 cool down is not a factor. The mostly all metal construction and overall quality is very good and the fact that this is really the first commercial AEG 4.5mm Steel BB Rifle makes that alone a great reason to pick one up.
Type:BB Rifle. Manufacturer: BARRA. Model: BARRA 400e. Materials: Mostly Metal with some plastic. Weight: 7.5 pounds (3.4 kilograms). Length: 42.25 inches (1073mm). Propulsion: AEG (with Deans Connectors). Action: Semi & Full Auto. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 50 rounds. (1000 shots per battery charge Aprox.) FPS: 410fps. Rate of Fire: 550+ rounds per minute in full auto (depending on battery voltage).
Trigger Pull: The trigger pull on the BARRA 400e AEG Full Auto BB Rifle like other AEG Rifles is not mechanical per say as it is essentially electrical driven so basically it is an on off switch that is closest in feel to a single action only trigger since it is light and short. You will notice a slight delay between pressing the trigger and the actual round being fired since the trigger activates a motor which first pulls the air spring back, once the spring is fully drawn back it releases and compresses the air which then propelled the 4.5mm steel BB. The higher voltage battery you use will shorten the delay as the motor will spin faster and pull back the spring quicker allowing for less noticeable delay and also a higher rate of full auto fire.
Accuracy: I have not Field Test Reviewed the BARRA 400e AEG Full Auto BB Rifle or even tried it out yet as it does not come with a battery or charger and as it uses a Deans connector I will need to get a battery that not only fits this gun size-wise but also has a Deans connector on it. Once I have this battery I will be able to make my Field Test Shooting Video for it. It should have a very consistent velocity since there is no CO2 cool down to factor in so each shot when I Chronograph it should be very similar in fps. I also expect accuracy to be decent since there will not be a lot of recoil as there is no blowback action here.
Build Quality: The BARRA 400e AEG Full Auto BB Rifle is almost all metal in design with an actual CNC machined aluminum hand guard and reciever! It feels very solid when holding it and the fit and finishes are really good. The only plastic I noticed on this AEG styled BB Rifle are the rear stock, pistol grip, and pop-up sights, everything else as far as I can tell are made out of metals.
Realism: The BARRA 400e AEG Full Auto BB Rifle is based on the AR platform in terms of its overall design and looks like a sub variant for sure. It is missing the default forward assist but in all the AIrgun versions of AR typo rifles the forward assist is just for show since there is nothing to assist with an Airgun. Most mechanical parts work as you would expect like the charging handle, magazine release, sectors switch, dust cover and of course the trigger.
Pros:
No CO2 required so cost to shoot is less.
Very consistent velocity as there is no cool down effect from CO2 cooling the gun.
Have the option to shoot in semi or full auto modes.
Almost all metal construction, very solid feeling gun.
Lots of rail option for mounting accessories (Picatinny on the top and M-LOK on sides and bottom).
Flip up sights use a dual mode, when not flipped up you have finer optic lower profile sights, when up there is a post in the front and peep in the back.
6 position adjustable rear stock.
Nice high capacity 50 round magazine, will need more mags for sure since you get 1000 shots per battery charge.
Comes with a speed loader too.
Lots of working parts including the charging handle, dust cover, magazine release, selector switch.
Selector switch is ambidextrous.
Cons:
No blowback operation as with some other Full Auto BB Rifles like the Crosman AR Series.
Does not come with a battery or charger, will need ones that fit and use a Deans connectors.
No red dot included with this version but the iron sights are well thought out.
Comments:
The BARRA 400e AEG Full Auto BB Rifle is something new to the Airgun industry and I always like it when a company doesn’t just make their own version of something we already have in the market and basically just put their branding and licensing on all the same guns. BARRA has made what I believe to be the first AEG 4.5mm Steel BB rifle at least one that has come to market and I always wondered why nobody has tried this before? Well here it is and now we get to see how well an AEG performs with 4.5mm Steel BB’s! Maybe this will start a new market of AEG type 4.5mm Steel BB Guns? I say if it works, well then go for it.
My Table Top Video of the BARRA 400e AEG Full Auto BB Rifle:
Type: BB Rifle. Manufacturer: Crosman. Model: R1 Fallen Patriots AR. Materials: Metal & plastic. Weight: 6 pounds (2.7 kilograms). Length: 26.25 / 29.25 inches (Stock closed / extended). Propulsion: 12 gram CO2 dual cartridges. Action: Semi & Full AutoBlowback - single action only. Ammunition Type: 4.5mm steel BB's. Ammunition Capacity: 25 rounds. FPS: 430fps. Rate of Fire: 1400 rounds per minute in full auto.
Trigger Pull: The trigger pull on the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is single action only since the charging handle must be pulled back first before you can shoot it. The trigger is short and fairly light as you would expect from an AR type trigger action. The real fun happens with the Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle when you switch it over to full auto mode and with just one pull and hold of the trigger you empty the 25 round magazine in mere seconds.
Accuracy: I have not Filed Test Reviewed the Fallen Patriot version of the R1 just yet but you checkout my Filed Test Shooting Video for the Crosman R1 Regular Version where I test out it using my Chronograph and I get an average of 385 fps and a nice 30 foot grouping of right around 1 inch in semi out and a decently tight full auto group of about 3-4 inches.
Build Quality: The Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle as with all the Crosman AR type BB Machine Guns is well made all around. Weighing in at 6 pounds without any add on accessories it feels solid and well built. There is a lot of metal going on inside and out of this rifle but keep in mind the top and bottom receiver are plastic with metal parts where they need to be like in the internals, pretty much all the working parts are metal, the magazine is full metal, the buffer tub is metal, charging handle, selector switch, magazine release, bolt release, trigger and of course the barrel is metal.
Realism: The Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is about as real as you are going to find in a CO2 Blowback AR/M4 styled Airgun. You can even take it apart and split the top and bottom receivers like the real steal version. The blowback action gives you some recoil but more importantly offers a true single action trigger and of course the full auto ability we all want and love. Almost all the working parts work like they would on a real AR/M4 other than the forward assist which is moulded into the receiver.
Pros:
Color scheme is awesome looking.
Super realistic working M4/AR 4.5mm BB Rifle just like the otters Crosman Rifles in this lineup.
Full blowback operation with both semi and full auto shooting, can feel the blowback operation rocking the gun.
Great weight and feel to it.
Almost everything works exactly like the real steel version. (Charging handle, dust cover, bolt release, magazine release, selector switch…)
Duel CO2 full metal drop out magazine that holds the 25 4.5mm steel BB’s as well.
Adjustable and customizable AR butt stock.
Included iron pop-up sights you can add a red dot sight on rail if you want to but looks classic without it..
Lots of rails for mounting additional cool hardware.
Removable flash hider that uses standard threading.
Cons:
Receiver is plastic but well made and does not compromise feel or weight since there is lots of metal throughout this gun.
No red dot included with this version.
Comments:
The Crosman R1 Fallen Patriots Blowback CO2 Full Auto BB Rifle is really pretty much the same as the Standard Version Crosman R1 with really only cosmetic color scheme changes. That said these cosmetic changes make it look awesome and in my books this is the nicest looking Crosman AR Series Full Auto BB Gun so far. I even like the fact that it comes with Iron Sights over a Red Dot. Typically I prefer a Red Dot as I find them easier to shoot with but on this version the iron sights really suit it and give it a more classic AR look to it. If you want you can easily add a Red Dot sight so do what every makes you happy.
My Table Top Video of the Crosman R1 Fallen Patriots CO2 Blowback BB Machine Gun:
In this Preview Unboxing Video I take a look at two full auto BB Machine guns but both very different and both from two separate companies. One is traditionally CO2 operated and the other is AEG operated which is a very new concept for a 4.5mm Steel BB Airgun. I have always wondered why nobody had attempted an AEG 4.5mm Steel BB gun before so here we have the first one to be released…
Starting with the Crosman R1 Fallen Patriots Full Auto CO2 BB Rifle it is essential a re-skinned R1 with a very unique coloration and of course the Fallen Patriots markings on it. The main receiver is a gun metal grey with black and red accents throughout and a purple-blue magazine. It really is stunning to look at and perhaps my favorite Crosman AR series Full Auto BB Gun to date. You do get pop-up Iron sights rather than a red dot which I feel suits this Airgun best and everything else in terms of specifications will be the same as the R1 so check that rifle out for more info.
Now the BARRA 400e is really something new to Steel BB Guns, basically it steals the AEG (Automatic Electric Gun) from what is typically reserved for Airsoft Rifles. I have always wondered why this technology has never been transferred over to 4.5mm Steel BB Airguns? Well now it has with the BARRA 400e Full Auto AEG BB Rifle. According to BARRA you can export to get around 410 fps and that should be super consistent since there is no CO2 cool down effect. You can also shoot in semi or full auto and it has a 50 round magazine that comes with a speed loader for easy loading. Another point to mention is that the BARRA 400e is almost all metal and feels really solid.
Starting with what the actual velocity of the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol. I made sure to keep the Sea Can and Airgun nice and warm before making this test and I also placed a brand new 12 gram CO2 cartridge in it and went with lead pellets I am guesstimating where around 7 grain so not super heavy or super light, definitely not high velocity alloy pellets. I was a bit shocked that my average fps was no where near the claimed 360 fps. My 5 shot average came to 259 fps with a couple shots even shooting under 200 fps which I through out. Is that good enough for shorter range plinking? I would say so but but way off the claimed 360 fps. Maybe the manufacturers claim was using high velocity light weight alloy pellets?
Next as with all my Field Test Shooting Videos for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol I performed my accuracy portion of the test and reloaded the 16 round magazine which is actually a dual 8 round rotary magazine you manually switch sides to unload all rounds. My first 8 shots for the most part where decently centered perhaps a bit to the right but the grouping was rather spread out close to a around 5 inches maybe even a bit more. I then rotated the magazine to the other side of fully loaded pellets and this time I had several malfunctions/jams where rounds did not rotate properly therefore getting squished rather than going down the barrel. I have a feeling this is a problem with this specific magazine as I had the same problem during my Velocity test. I even switched to pointed pellets for the accrual test from flat head pellets but it did not seem to help. The best I could do on this day with this gun was to get around a 5-6 inch grouping which is not very good for a pellet shooter at 30 feet out
As I mentioned in the video I only test the guns, I don’t make them and as with any product out there it is possible I got a lemon since it seems to me like only one side of the rotary magazine was giving me the problems with jamming pellets. That said even the side that was more consistent did not shoot a very tight grouping for me. If it was my money to spend and I wanted a 24/7 styled Replica Airgun I would probably go with the blowback CO2 BB version since I had a lot better performance from that pistol with the addition of blowback action and a much lighter single action trigger.
In this Field Test Shooting Review of the KWC PM Makarov Non-Blowback CO2 Pellet Pistol I find out what the actual Velocity is and how accurately I can shoot it at a paper target setup 30 feet down range. If you have not already watched my Table Top Review for the KWC PM Makarov Non-Blowback CO2 Pellet Pistol then make sure to do so to see some nice closeup video of it and all the details and specifications laid out for everyone.
Starting with what the actual velocity of the KWC PM Makarov Non-Blowback CO2 Pellet Pistol. I made sure to keep it nice and warm before making this test and I also placed a brand new 12 gram CO2 cartridge in it and went with lead pellets I am guesstimating where around 7 grain so not super heavy or super light, definitely not a high velocity pellets. I was a bit shocked that my average fps was no where near the claimed 340 fps. My 5 shot average came to 263 fps with the highest being 272 fps and the lowest being 256 fps. Is that good enough for shorter range plinking? For sure but far off the called 340 fps. Maybe the manufacturers claim was using high velocity super light weigth pellets?
Next I performed my accuracy portion of the test and reloaded the 12 round magazine which is actually a dual 6 round rotary magazine you manually switch sides to unload all rounds. My first 6 shots I pointed the KWC PM Makarov Non-Blowback CO2 Pellet Pistol right at the bulls eye and found out it shoot a bit on the low side so only two rounds actually made it on the paper. I then switched to the other 6 round rotary magazine and aimed a bit higher, this time I was able to get fairly well centered on the target and produce about a 3 inch grouping. So in other words no awards are going to be handed out for this pistol in terms of accuracy or power. By the way I was using my standard shooting stance which is with my hands stabilized on a sand bag up front and sitting on a stool in the back.
The KWC PM Makarov Non-Blowback CO2 Pellet Pistol is not listed as any sort of target pistol so I was not expecting world class performance but I was expecting it to shoot a little bit better than your average blowback CO2 BB shooter and it really didn’t at the end of the day. If you’re specifically looking for a pellet shooting Makarov then this will be your Airgun since I am pretty sure it is the only one out there at this time but personally I would go with one of the CO2 Blowback BB versions since they shoot a bit harder and are maybe even more accurate not to mention you also get that blowback recoil with a nice light single action trigger.
Type: Pellet Air Pistol. Distributer:KWC. Model: KWC 24/7 TAC NBB Pellet. Materials: Metal and polymer build. Weight: 1.76 pounds (799 grams). Barrel: Rifled steel. Propulsion: CO2 x1. Action: Semi auto non-blowback, double action only. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 16 rounds (2x8). FPS: 360-370.
Trigger Pull: The trigger pull on the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is a bit on the medium to heavy side so it’s not going to make for the best action shooter as it is a double action only shooter when compared to a single action only trigger or a single and double action trigger. As with most double action triggers it is a bit longer and slightly heavy but not unusable, just be prepared to get a little bit of a finger workout.
Accuracy: I have not shot the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol just yet but will be doing so probably next week so stay posted for my Full Field Test Shooting Video for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol. I expect it to perform well in terms of accuracy and power since there is no blowback operation to have to compensate for. Having a rifled barrel should also help with accuracy! We will see shortly.
Build Quality: The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is built as expected just like all the other KWC Airguns. KWC has been making Airguns for a while not just for themselves but for other companies like Umarex, Gletcher, ASG, Crosman and even Sig Sauer and so quality control and durability have to stand up to these manufacturers standards. You will find metal on this gun where it matter. The slide, the full size drop out metal magazine and of course lots of internal parts. The frame, magazine release, trigger and safety are all plastic. I do like the feel of the rubberized grips for sure! Fit and finish is good overall and the fact that this is a fairly simple Airgun design with no blowback action or even a moving slide, so less moving parts means there is less chance for something to go wrong so it should last a while even with a fair amount of use.
Realism: The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol shares it’s looks with the Taurus 24/7 but is not an exact replica. The trigger guard is a bit different and so is the placement of the controls and even the slide and frame are not exact but very similar. In terms of size, weight and vernal overall design for sure the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol looks a lot like a Real Steel Taurus 24/7 at first glance.
Good weight and solid feeling gun. Lots of metal where you need it in the slide, magazine and other internals.
All metal full size drop out magazine holds CO2 and 16 pellets.
Decent looking replica (but not bang on) of a Taurus 24/7.
Not a lot of writing on the gun, very clean looking (Non Ranger version).
Recessed barrel helps with look of realism.
Fiber Optic front and back sights for easy sight acquisition.
Rifled barrel will help with accuracy.
Non-blowback operation with increased fps and CO2 efficiency.
Rail on top of slide and frame for lots of accessory add on options.
Double action trigger is long but not overly heavy so should be OK for action shooting.
Cons:
No blowback, slide is fixed and does not move but can be removed with a tool for internal access and cleaning.
No single action shooting so may not be the most accurate for slowed down shooting.
Sights are not adjustable but you can add an adjustable red dot to it using the rail setup.
Hard to tell when out of ammo, have to listen to the sound or count shots.
Comments:
It is nice to see more full size drop out metal magazine Replica Pellet Pistols coming out in the Airgun market just liek the KWC Makarov PM I just reviewed. Generally speaking most are going to be non-blowback but there are a few blowback options. That said a Non-blowback CO2 Pellet Pistol like the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol will typically give you a high velocity and more shots per CO2 and can even be a little bit better in the accuracy department since there is virtually no recoil from them. The KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol is a nice little Taurus 24/7 looking Airgun that has a nice modern look and feel to it. Hopefully it performs well for me during my Field Test Shooting Video I will be making soon for it.
My Vimeo Videos for the KWC 24/7 TAC Non-Blowback CO2 Pellet Pistol:
Type: Pellet Air Pistol. Distributer:KWC. Model: PM Makarov Pellet. Materials: Metal and polymer build. Weight: 1.7 pounds (754 grams). Barrel: Rifled steel. Propulsion: CO2 x1. Action: Semi auto non-blowback, double action only. Ammunition Type: .177 caliber pellets. Ammunition Capacity: 12 rounds (2x6). FPS: 344-370.
Trigger Pull: The trigger pull on the KWC PM Makarov Non-Blowback CO2 Pellet Pistol is not going to make for the best action shooter out there as it is a double action only shooter when compared to a single action only trigger or a single and double action trigger. That said it works fairly well as long as you make sure to fully release it after each shot, short releases may result in the hammer not going back all the way and a misfire. As with most double action triggers it is a bit long and slightly heavy but not unusable, just be prepared to get a little bit of a finger workout.
Accuracy: I have not shot the KWC PM Makarov Non-Blowback CO2 Pellet Pistol just yet but will be doing so shortly so stay posted for my Full Field Test Shooting Video for the KWC PM Makarov Non-Blowback CO2 Pellet Pistol. I expect it to do fairly well in terms of accuracy and power since there is no blowback, it is a pellet shooter after all and the barrel is rifled. We will see shortly…
Build Quality: The KWC PM Makarov Non-Blowback CO2 Pellet Pistol is built just like all the other KWC Airguns, it’s not going to be the best quality but it is decent and KWC has been making Airguns for a while not just for themselves but for other companies like Umarex, Gletcher, ASG, Crosman and even Sig Sauer. You will find metal on this gun where it matter. The slide, the full size drop out metal magazine and of course lots of internal parts. The frame, trigger, fake hammer and safety are all plastic. Fit and finish is good overall and the fact that this is a fairly simple Airgun design with no blowback, so less moving parts means there is less chance for something to go wrong so it should last a while even with lots of use.
Realism: The KWC PM Makarov Non-Blowback CO2 Pellet Pistol really does look and feel like a real steel Makarov PM semi auto pistol with the exception of the ejection port which is not cut out. everything is really believable even though not all the parts work like the slide, slide catch release and fake hammer. On a real Makarov PM the frame would also be metal adding to the overall weight but the KWC PM Makarov Non-Blowback CO2 Pellet Pistol comes in at 1.7 pounds which is actually very close to the weight of a non-loaded real steel Makarov PM which weighs around 1.6 pounds but will be a lot heavier fully loaded.
Good weight and solid feeling gun. Lots of metal where you need it in the slide, magazine and other internals.
All metal full size drop out magazine holds CO2 and 12 pellets.
Decent looking replica of a Makarov PM.
Not a lot of writing on the gun, very clean looking (Non Ranger version).
Recessed barrel helps with look of realism.
Rifled barrel will help with accuracy.
Non-blowback operation with increased fps and CO2 efficiency.
Working safety in same position as real steel version.
Double action trigger is a bit long but not overly heavy so should be decent for action shooting.
Cons:
No blowback, slide is fixed and does not move either.
Hammer moves but does not cock back for single action shooting and is made out of plastic.
Sights are not adjustable and are all black so shooting at darker objects will be a bit more challenging.
Hard to tell when out of ammo, have to listen to the sound or count shots.
Comments:
It is nice to see more full size drop out metal magazine Replica Pellet Pistols coming out in the Airgun market. Generally speaking most are going to be non-blowback but there are a few blowback options. That said a Non-blowback CO2 Pellet Pistol like the KWC PM Makarov Non-Blowback CO2 Pellet Pistol will typically give you a high velocity and more shots per CO2 and can even be a little bit better in the accuracy department since there is virtually no recoil from them. The KWC PM Makarov Non-Blowback CO2 Pellet Pistol is a nice little Replica Airgun that looks the part, feels the part and hopefully turns out to be a fun and accurate Pellet Plinker at the end of the day.
My Vimeo Videos for the KWC PM Makarov Non-Blowback CO2 Pellet Pistol:
In this Field Test Shooting Video I test out the Umarex T4E HDX .68 Paintball Shotgun to find out what the actual fps is and if .68 Caliber Rubber Balls shot out of this Paintball gun are even going to be somewhat accurate at 30 feet out? If you have not already watched my Table Top Video where I go over the details and specifications with some closer up video showing you around the Umarex T4E HDX .68 Paintball Shotgun then make sure to watch it here…
Starting with the velocity portion of this video I used .68 caliber rubber balls which are not super heavy and not made out of a very hard rubber as you can squish them with your fingers fairly easily. I put 5 rounds through my chronograph after loading a pair of 12 gram CO2 cartriges into the CO2 chamber. My results averaged 206 fps which may seem slower than expected but they did hit my target pretty hard and actually knocked the cardboard backing right off of it. Each round was fairly consistent ranging from 203 to 210 fps.
Moving on to the accuracy portion of this test I proceeded to shoot around 10 rounds into my fresh paper target setup 30 feet down range. My target is basically an 8.5 x 11 sheet of paper and my goal was ot get all my shots onto the paper which I managed successfully. I would say most of the rounds all hit within about 5-6 inches of each other which for a Paintball Gun is very good! Keep in mind I was shooting using a seated position with the Umarex T4E HDX .68 Paintball Shotgun rested up front on a sand bag.
All in all the Umarex T4E HDX .68 Paintball Shotgun performed really well shooting consistent velocities and also getting all the rounds on an 8.5 x 11 inch target easily at 30 feet away which means if you where shooting at a persons body area you would easily hit it every shot making this a decent close quarters shooter which is what it really would be used for at the end of the day. Could you use it for less lethal home defense? I guess so especially if you can get your hands on pepper balls but I am not sure if regular rubber or paintballs balls would stop someone? Just seeing this impressive shotgun may in fact be more of a deterrent then being shot by it, but if it get’s the job done then why not.
