Type: Pellet air rifle.
Manufacturer: Baikal.
Model: IZH MP-61.
Materials: Metal & plastic.
Weight: 4.3 pounds.
Barrel: 18.5 inches, metal-rifled.
Propulsion: Spring piston.
Action: Repeater.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 5 rounds.
FPS: 490.
Trigger Pull: The trigger pull on the IZH MP-61 is a nice light 1.4 pounds and the release stage is also adjustable, you actually need to be careful of accidental shots as the trigger is light enough to go off before you are ready to shoot.
Accuracy: Very good, I was not so sure when first using the IZH-61 with my initial scope and pellet setup but my second open sight test with different pellets yielded a very tight 1 inch group from 30 feet out in a standing unrested position.

Build Quality: This is a no-nonsense gun made Russian style, it is built to be cost effective so there are parts that could be made with metal that are plastic but there isn't anything on this gun that feels cheap or poorly built. Baikal also doesn't cheap out on the plastic as not all plastic is the same. I actually dropped the IZH MP-61 right on the front hooded sight without any adverse effects, cheap plastic would have cracked and broken.
Realism: Since the Baikal IZH-61 is not a replica gun, I can not really compare it to any existing one rifle out there, but it does look very tactical in design, much more so then your standard spring piston air rifle.
Purchased this rifle from: The Replica Airguns Store.

Pros:

• Inexpensive spring piston rifle.
• Very unique looking air rifle.
• Side pull lever design.
• 5 round magazine/clip.
• Right on the money with FPS.
• Adjustable Stock.
• Adjustable Trigger.
• 11mm dovetail rail mount for scopes.
• Very light weigh and easy to cock.
• Made in Russia

Cons:

• Plastic stock seems to mark up easy - kind of part of the utilitarian look.
• Mechanics takes a bit of getting use to.
• Scope rail mount is a bit short.

Comments:
The Baikal IZH MP-61 is a really nice low cost yet full featured air riffle! You really get a lot of rifle for your money: You get an efficient side lever design with a 5 shot magazines for quick repeat shots, a very light weight and adjustable trigger, an adjustable stock, a rail mount for a scope and one of the more tactical looking air rifles available on the market. The Baikal MP-61 also takes the FPS right up to the limit without going over so no license or PAL is required to own this one in Canada. This air rifle is designed for target shooting but could also be used for small pest control if your marksmanship is good enough to hit the vital kill zones of your prey.

My YouTube Video Review for this Russian made Air rifle:

Buy this rifle in Canada   -   Buy this rifle in the US

Another new product arrives at the

Replica Airguns Store

The Baikal IZH-61 has a very interesting style and design, it is compact, lightweight and a truly affordable air rifles that offers a unique blend of attributes inherent in hi-class sporting weapons such as a five way adjustable trigger, an adjustable stock,an adjustable rear sight and fully hooded front sight. The Baikal IZH-61 also has provisions to mount a scope or red dot sight.

Some other interesting design element are a fixed barrel with a heavy duty side cocking lever and a 5 shot pellet magazine fed into the barrel by a slide feeder ensuring high pattern results.

• .177 caliber pellets
• 5 round magazine
• Sidelever Spring-piston
• 10.5 pounds cocking effort
• Up to 490 fps
• 4.3 pounds
• 18.5 inch rifled barrel
• 33 inches total length
• 1.4 pound trigger pull
• Adjustable rear sight
• 11mm dovetail scope mount
• Made in Russia

Buy Baikal IZH MP-61 5 in Canada

Related Posts:

• FULL METAL UZI BLOWBACK CO2 .177 BB GUN ON ITS WAY

• CYBERGUN MINI UZI BB GUN REVIEW

• CYBERGUN MINI UZI CO2 BB GUN CHRONOGRAPH AND FULL AUTO SHOOTING TEST

"Before you attempt to do this modification you need to be aware that it may void your warrantee and/or you may fail and either break something or incorrectly reassemble your Mini UZI rendering it "Broked"! This is your problem so please do not attempt this modification (even though it is fairly easy to do) unless you're 100% confident you can do it and are aware of the possible consequences. Make sure to also take into account any gun laws in your area prohibiting full-auto capable firearms!"

(Special thanks to Herman for showing me the ropes on this modification)

This modification will make your semi-auto "only" Cybergun/KWC Mini UZI BB Gun into a full auto capable 4.5mm BB machine gun. From the factory the full auto switch position (Far Left "A") is disabled but the full auto selector position is visible. The actual full-auto functionality is still present in the Mini UZI but has been decommissioned by the simple means of blocking the selector switch from being moved to the far left full-auto or "A" position.

This full auto modification will show you how to disassemble the Cybergun - KWC Mini UZI BB Gun and remove the small plastic selector switch blockage so you will be able to manually switch between semi auto and full auto modes. This modification takes about 15 minutes to complete.

<!-- google_ad_client = "ca-pub-9036472715040282"; /* Replica Airguns Content */ google_ad_slot = "1487049688"; google_ad_width = 468; google_ad_height = 15; //-->

You will need the following tools: A pair of pliers and either a pair of small wire cutters or a file.

Let's begin! Below are the two pre-modification positions available from the factory:

"S - SAFE"

"R - SEMI AUTO"

Below is a closeup of the top bolt cover that we will be removing to access the internal bolt for removal:

In the next photo we have removed the bolt cover by pressing the "angled button" towards the rear sight:

And now the bolt is removed:

I removed the grips but this is not necessary:

Now you will need to remove the lower receiver pin located at the back end of the receiver closest to the grip safety. Use a pair of pliers to pinch the metal pin while pushing it through. Once the pin is started you can use the pliers on the other side to pull the pin all the way out. You may need to us a fair amount of force to do this as the fit of the pin is tight:

Once the pin is removed the lower receiver can be detached:

You can see in the picture below the small plastic nub that we will need to remove in order to restore full-auto capability:

I used a pair of small wire cutters to clip this plastic nub off, but you could use a file too. Just make sure that the plastic is flush and does not have any burs or protrusions.

Below is a photo of the Plastic Nub removed from another angle:

After that, all you need to do is reassemble you Mini UZI in revers order to finnish the Full Auto modification.

In the below Photos you can see we have restored the ability to move the fire selector switch over to the "Far Left" or "A" position, reenabling the Cybergun - KWC Mini UZI BB Gun to shoot in full auto when desired.

"A - FULL AUTO"

Now enjoy your Cybergun - KWC Mini UZI BB Gun in full-auto as it was originally designed!

Here is my Vimeo Video in Narrative with Photos:

Buy this gun in Canada

Buy this gun in the US

This Article was graciously provided by one of my viewers: Lee

Related Posts:

• SIG SAUER X-FIVE STAINLESS STEEL VERSION

DISCLAIMER, PLEASE READ AND UNDERSTAND!

• This walkthrough is for information purposes ONLY, if you decide to dismantle your BB gun you will void any warranty you have with the manufacturer.
•  I will not be held accountable for your actions or any damage that is caused by your negligence. Therefore, if YOU decide to dismantle your BB gun and break something during the dismantling or assembling it is your problem not mine.
• If you don’t feel confident or comfortable doing any of these steps STOP and do not proceed any further or you may do damage.
• YOU WILL LOOSE ALL THE SIG SAUER MARKINGS ON THE GUN.

Having said all that, this is my first ever instructional so I’m going to try and make this walkthrough as easy as I can for you to understand. You will need the following: Flat tip Screwdriver for the grips, Small Philips Head screwdriver, small punch & needle nose pliers – the last 2 are optional.

Make sure you have a clean work space and lay out every part in the order that you remove it Left to Right, come reassembly time you work Right to Left it makes reassembly so much easier.

Step 1:

Field Strip the slide until it looks like this:

Unscrew these 2 screws, these hold in the “Breech Block” once your unscrewed cup the end of the slide in your hand and let the Breech & Screws fall in your hand – Set these aside.

That’s it your Slide should look like this:

It is now ready for paint removal.

Step 2:

Take the Frame and start removing the grips Left hand side first:

Flip the frame over and remove the right hand side grips:

Carefully remove the trigger return spring, it is under tension and it WILL fly across the room – I spent an hour looking for it one day! Also while we are at it, you can remove the cover to the magazine release.

To remove the safety, place your flat tip screwdriver between the frame and the safety and twist ever so gently this will separate the safety and all you need to do now is grab the safety from either side and gently pull & wiggle until it separates.

Once the safety is removed you will see the safety bar, this lifts off.

Step 3:

Lift this little pin out and remove the spring, very carefully push this pin from the other side and remove, be careful because once this happens your hammer assembly is loose and free from the frame.

Slowly and gently remove the hammer assembly:

Note the little shiny piece that sits on the side of the hammer assembly, try very hard not to let this piece fly out, it is a pain to get back in, if it does fly out keep calm and take your time, don’t force the little spring in, it seats in behind the shiny metal thing – sorry I don’t have a proper name for it.

Also make sure that the spring next to it is in the locked open position, if it snaps back just get the tip of a small screwdriver and slide it to the left until it locks.

The hammer return spring assembly at the back of the grips can be removed and set aside.

Removing the trigger assembly is easier than it looks; you need to remove the takedown lever by rotating it counter clockwise until it stops.

Push it through the frame and rotate it back clockwise to remove it all together.

Remove the screw holding the trigger assembly:

Lift out the trigger assembly; be careful of the slide lock spring it wont Fly out, but it will fall out.

If you want to remove the magazine release, there is a spring that sits at the rear of the trigger guard;

Push the magazine release in part way & with the flat tip screwdriver lifts the up to remove it, once removed the magazine release will simply fall out.

THAT’S IT! We’re done, ready for the paint removal. Any paint stripper is fine.

KEEP IT WELL AWAY FROM THE PLASTIC PARTS!

Follow the manufacturer’s guidelines for use of their product and thoroughly clean the slide and frame after you have removed the paint.

YOU WILL LOOSE ALL THE SIG Sauer MARKINGS ON THE GUN.

Rub over the slide and frame with #0000 Steel wool or 1200 grit Wet & Dry paper. Clean again and using the paper or steel wool with some ALUMINUM polishing compound like Autosol and some good ol fashioned elbow grease polish the slide and frame until you reach your desired outcome. Clean it all down again and wipe it down with a rag that has had gun oil or my preference “Fluid Film”.

Reassemble the gun in the reverse order and viola one shiny SIG Sauer X-Five.

Buy this gun in Canada   -   Buy this gun in the US