View fullsize

As with most of the new tech I purchase or acquire that I will be using in my Videos for either my GetFitOver40 or ReplicaAirguns YouTube channels, I generally like to do some sort of a practical review for the item. In this case I take a look at the Synco G1 (A2) Wireless Microphone Set which is a pair of wireless transmitters that pair with a single dedicated receiver allowing me to quickly and easily capture good quality audio for my Videos.

For the past couple of years my go to microphone setup for my video was to use a generic lapel mic connected to my Samsung Galaxy Smartphone recording into an audio program. I would then send the audio file via dropbox to my computer where I would then line up the audio file with the video file in my video editing software to get a much higher quality and more clear voice recording versus what the camera mic would be able to capture.

This system has been working fairly well for me but required a somewhat cumbersome lapel cable and of course my bulky Smartphone in my pocket at all times but did allow me to be as far away from the camera as I wanted without any interference or loss of audio clarity.

View fullsize

After playing around with the Synco G1 (A2) Wireless Microphone System I have determined I will most likely simply be clipping the transmitter onto my shirt without the lavaliere mic plugged in and transmitting the audio into either my Samsung Smartphone or my iPad where I can then again dropbox the audio file to wherever I plan on editing the video.

This video was kind of a test to see how everything sounded in terms of the lapel mic versus the built in mic. What settings to use and how distance effected the audio signal and quality. Unfortunately the lapel mic was a bit close to my voice causing some distortion to occur but you can still hear what I am saying no problem. In the future I would place the lapel mic a bit further away from my voice lower down on my shirt or simply use the built in mic as it was not as sensitive to this distortion and seemed to handle louder volume much better than the lapel mic.

View fullsize

Here are some of the specifications for those that like that sort of info :)

Transmitter (TX )

• Wireless Transmission - Digital 2.4GHz

• RF Frequency Band - 2400-2483.5MHz

• Working Distance - 164ft/50m (LOS area) 98ft/30m (NLOS area)

• Latency - 12.5ms

• Mounting - Pocket Clip

• Audio Input - 1/8" / 3.5 mm TRS Mic Input

• Audio Input Level - 1V (0dBV)

• RF Output Power - ＜10mW

• Power Requirement - 3.3V-4.7V

• Battery Type - Built-in Lithium Battery

• Battery Charging Time - 1.5h

• Battery Life - 5h

• Dimensions - 52X42X16mm

• Material - Plastic

• Weight - 35g

Receiver (RX)

• Wireless Transmission - Digital 2.4GHz

• RF Frequency Band - 2400-2483.5MHz

• Approximate RF Sensitivity - -81dBm

• Working Distance - 164ft/50m (LOS area) 98ft/30m (NLOS area)

• Latency - 12.5ms

• Mounting - Pocket Clip

• Number of Audio Channels - 2

• Audio Output - 1/8” / 3.5 mm TRS Mic Output - 1/8“ / 3.5 mm TRS Headphone Output

• Gain - 0-4 Level (0 to 8dB)

• Audio Output Level - Line Out: 1V, Monitoring: 25-30mW

• Power Requirement - 3.3V-4.7V

• Battery Type - Built-in Lithium Battery, 400mAh

• Battery Charging Time - 1.5h

• Battery Life - 5h

• Dimensions - 52X42X16mm

• Material - Plastic

• Weight - 35g

Microphone

• Form Factor - Built-in/External Mic

• Sound Field - Mono

• Polar Pattern - Omnidirectional

• Frequency Response - 50Hz-20KHz

• Sensitivity - -40dB (±3 dB, re 1V/Pa at 1KHz)

• Max. Input SPL - 135dB SPL (at 1KHz)

I made a video a little bit ago talking about how Canada’s new Bill C-21 will affect pretty every gun owner in Canada including even airgun owners of BB, Pellet Airsoft and even Paintball Guns. Make sure to watch that video first called Bill C-21 Canada is Going After Your Red Ryder BB Gun.

This video is all about how you can get involved in making some waves by signing two online petitions along with contacting your local Member of Parliament and letting them know your disapproval of Bill C-21 and all that it imposes on law abiding Canadian gun owners.

Probably the most important online petition to sign would be the House of Commons Petition E-3201 Bill C-21 so make sure to sign that one!

The other online e-petition we need to sign is the change.org petition.

And lastly but also super important is to send an email to your local member of Parliament again let them know your disapproval of Bill C-21. I have included a link to the web[age where you can locate your local MP and below that is a template of what you could include in your email to them.

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

Dear (MP),

I am a constituent in your riding. I am writing to you to voice my concerns over the new provisions that were announced under the proposed Bill C-21, and how this will impact myself, my community and many other Canadians.

"Criminal Code 1 (1) The definition replica firearm in subsection 84(1) of the Criminal Code is replaced by the following:

replica firearm means any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm; (réplique)

(2) Section 84 of the Act is amended by adding the following after subsection (3.1): Certain firearms deemed to be prohibited devices

(3.2) For the purposes of sections 99 to 101, 103 to 107 and 117.03, a firearm is deemed to be a prohibited device if

(a) it is proved that the firearm is not designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second or at a muzzle energy exceeding 5.7 Joules; and (b) the firearm is designed or intended to exactly resemble, or to resemble with near precision, a firearm, other than an antique firearm, that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules."

Make sure to also sign ePetition e-3201 to put a stop to Bill C-21:

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

The long and short of it, Bill C-21 is an attack on law abiding Canadian gun owners and goes so far as to include the Daisy Red Ryder BB gun and many other Airguns as a Prohibited Firearm in Canada.

I am not a Lawyer or Bureaucrat so this video is my personal take on how I perceive the new Gun laws and Bill C-21. Please do your own investigation on these new laws and come to your own conclusions.

I don’t ask this often, please like and share this video with as many people as you can in Canada and outside of Canada. This is a new level of attack on Canadian Gun rights and we need to stand up for our gun rights or there will be no more guns in Canada eventually. This could happened in your country and has already happened in many others.

Make sure to also sign the change.org petition and call/email your local MP’s and Firearms Officers

https://www.change.org/p/canadian-government-stop-bill-c-21

Make sure to also sign ePetition e-3201 to put a stop to Bill C-21:

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

Find your local MP:

https://www.ourcommons.ca/Members/en/search#

So how did we get here… Back in May of 2020 Trudeau (without going through Parliament) banned some 1500 (what he referred to as) Assault rifles. For the most part but not exclusive to, anything that looks scary with a semi auto action. Many rifles with semi auto actions that did not look scary where not on this banned list. Some bolt action rifles and even shotguns made it to this banned list of guns deemed by Trudeau as dangerous Assault Rifles.

Bill C-21 is now going after handguns in a similar capacity along with any Airgun that looks like a Firearm. 

In this video I am going to focus mainly on the Airgun side of how Bill C-21 effects Canadians so we are talking about BB Guns, Pellet Guns, Airsoft Guns, even Paintball Guns. But do understand if you own a handgun or even a rifle, Bill C-21 is coming after many of those guns as well making them literally impossible to own and use in any capacity other than keeping them in a safe at all times until you die in which it has to be relinquished without payment to the government.

How does Bill C-21 effect Airguns? Previously most Airguns where classified as Firearms but where unregulated so they didn’t require registration or even a Firearms license to sell, buy, own or use. Bill C-21 wants to make any Airgun that looks like a firearm (other than an antique firearm) prohibited. This means you will not be able to import, sell, or buy them in Canada. You will be able to keep your existing Prohibited Airguns but with extensive limitations on how you can keep and use them. Basically no use at all.

For the most part you will want to keep your now prohibited Airguns in a gun safe at home at all times or you risk having them confiscated from you since if you are transporting or using an Airgun, the police have the right to ask you to produce a Prohibited Firearms license which if I am not mistaken has not been made available since 1991, so the vast majority of gun owners especially none license holding Airgun owners do not have a Prohibited Firearms license nor is there any way to obtain such a license. How convenient!

Who does Bill C-21 effect? Firearms in Canada is a Multi Billion dollar industry and Airguns are an ever growing part of that industry. Bill C-21 effects Importers, Wholesalers, Retailers, Gun Ranges, Airsoft Fields, Gun Organizations, Gun Groups and of course every Firearm and Airgun owner in Canada. Bill C-21 wants to eliminate many aspects of the firearms Industry in Canada putting large and small business out of business. Replica Airguns will be gone if Bill C-21 passes in Canada, a business I founded and have been part of for over 15 years affecting many employees, families and of course customers.

How will Bill C-21 by eliminating the vast majority of Airguns in Canada keep Canadians safer and save lives as it proposes? I’m tryin to wrap my head around this one… So please tell me how many Pellet Rifles where used in mass shootings? How many drive by shootings involved Paintball guns? How many suicides have there been with BB pistols? How many police officers have died at the hands of an Airsoft wielding mad person? I’m going out on a limb here to say probably zero. And if any of these Airguns had been used in any of these situations that would have been a good thing because no lives would have been lost perhaps except for the user of the Airgun.

I want to end this video off with an example and an analogy of just exactly how ridiculous Bill C-21 is and how it will do absolutely zero to protect Canadians from criminals.

• Daisy Red Ryder BB Rifle (1940) Will now be a Prohibited Firearm in Canada

• Crosman 38T Pellet Revolver (1964) Will now be a Prohibited Firearm in Canada

• Crosman 357 Pellet Revolver (1983) Will now be a Prohibited Firearm in Canada

• Air-Ordnance SMG 22 Caliber Full Auto Machine Gun (Modern Airgun) Currently and even after Bill C-21 will be an Unregulated Firearm in Canada with no license or registration required.

Analogy of how Bill C-21 is supposed to Make Canadians Safer:

Bill C-21 is going after law abiding Licensed and Registered gun owners and only allowing them to keep their now Prohibited Guns but not allowed them to use their prohibited guns in any capacity. Prohibited guns must be in a safe at all times unloaded and locked. You are not allowed to transfer them anywhere, you are not allowed to sell, loan or give them to another person, and upon death the prohibited gun/s must be relinquish to the Government. According to Bill C-21 this is apparently going to help stop non license holding non gun registered criminals from committing gun related crimes that for the most part do not obtain their firearms legally.

This is like saying that ICBC (Canadas Vehicle Insurance Agency) has looked into motor vehicle accidents and found that a high majority of vehicle accidents are caused by people that do not have drivers licenses and that do not have registered or insured vehicles, furthermore ICBC has come to the conclusion that vehicles related to these accidents often times are import sedans that have been lowered and tuned. So in order to reduce car accidents ICBC will be focusing on drivers with drivers licenses and registered and license vehicles that fit this description and any other vehicle they deem a possible threat , these registered and licensed vehicle owners will still be allowed to own their vehicles that fit this criteria and have them registered but they will not be allowed to drive their vehicle/s anymore. Their vehicle/s must be kept in the garage at all times and never driven. You can not sell or loan your vehicle/s to anyone and these vehicle/s will not be allowed to be imported, bought or sold anymore in Canada. Once you die your vehicle/s are relinquished by the Government without payment no matter what their assessed value.

Please make sure to sign the change.org petition and call/email your local MP’s and Firearms Officers

https://www.change.org/p/canadian-government-stop-bill-c-21

A really informative video on how Bill C-21 will effect Airguns (BB, Pellet, Airsoft, Paintball) in Canada.

It is important that we as a community understand the impact Bill C-21 will have on our sport, hobbies, and livelihoods. We know everyone is concerned with the possible outcome that this could have for our sport and we cant thank you all enough for for your support in this time. We want you to help you exercise your rights and voices. If there is a hope of saving our sport it will come down to letting our MP's know that we will not stand by and let the rug be pulled from under us. If you want more information regarding Bill C-21 and it's implications to firearms regulation we have some links in this post so you can read the proposed legislation yourselves. For now we would like to invite you to sign the petition at change.org and help us in the fight to keep Airsoft alive in Canada.

#stopbillc21

https://www.publicsafety.gc.ca/cnt/cntrng-crm/frrms/c21-en.aspx

https://www.change.org/p/canadian-government-stop-bill-c-21

View fullsize

In this YouTube Video I test out my new Insta360 One R with the 1 Inch Mod, comparing it to my Sony RX 100 IV to see how they compare against each other.

It’s not really a fair comparison since my Sony RX 100 IV is now 5 or 6 years old which is a long time for a digital camera but it has been really good to me and provided some really great quality video over the years. Compare that to the Insta360 One R that is about a year on the market now and you would think the clear winner would be the Insta360 One R.

On it’s own the Insta360 One R with the standard 4k lens would perform well against the Sony RX 100 IV but the Sony RX 100 IV has a 1 inch sensor allowing it to get the most out of each pixel and since I primarily shoot in 1080p 60 frames per second I need to get as much out of each pixel as I can.

View fullsize

One really great feature about the Insta360 One R is that it is modular so I can swap the 4k module out for a 5.7 k 360 module or even a 1 inch 5.3k module allowing both the Insta360 One R and the Sony RX 100 IV to have that large 1 inch sensor keeping the comparison more inline with each other.

Some things to not that will make a big difference in quality and limitations for this video is that the Insta360 One R 1 Inch Mod was shot using 4k 60 fps while the Sony RX 100 IV was shot using 1080p 60fps. The Insta360 One R 1 Inch Mod has a fixed focus while the Sony RX 100 IV has a variable focus.

Anyway I will let you be the judge and decide which camera you like the look of the video for at least in this shooting situation.

View fullsize

This is by far not a full Review of the Insta360 One R Camera but rather more of my take on the Insta360 One R Camera and what it can do for me and how I plan on using it in by Replica Airguns and Get Fit Over 40 YouTube channels.

View fullsize

I talk about how the Insta360 One R Camera compares to a GoPro type camera and how it can also be much more than a typical action camera because of its ability to morph from one camera to a completely different type of camera because of its modular form factor. Not to mention possible future new hardware lenses and even main modules that could increase the ability of this camera even further.

View fullsize

In this video I show some sample videos I shot using the Insta360 One R Camera with the 4K 60 fps Mod and its 5.3K 30 fps 360 Mod Lenses.

View fullsize

Here are some of the basic Specifications for the Insta360 One R Camera:

Aperture

4K: F2.8

360: F2.0

35mm Equivalent Focal Length

4K: 16.4mm

360: 7.2mm

Photo Resolution

4K: 4000 x 3000 (4:3), 4000 x 2250 (16:9)

360: 6080 x 3040 (2:1)

Video Resolution

4K: 4000x3000@24/25/30fps, 3840x2160@24/25/30/60fps, 2720x1530@24/25/30/60/100fps, 1920x1080@24/25/30/60/120/200fps,

360: 5760x2880@30fps, 5760x2880@24fps, 5760x2880@25fps, 3840x1920@50fps, 3840x1920@30fps, 3008x1504@100fps

Photo Format

4K: jpg, RAW (dng) (RAW files require software on PC/Mac to export.)

360: insp (can be exported via App or Studio), RAW (dng) (RAW files require software on PC/Mac to stitch)

Video Format

4K: insv (can be exported via App or Studio), mp4 (enable in-camera basic stabilization), * The .insv video format has been changed to .mp4 in firmware 1.2.16 and later

360: insv(can be exported via App or Studio), LOG and HDR videos

Video Coding

4K: H.264 / H.265

360: H.264 / H.265

Video Modes

4K: Standard video, HDR video, Timelapse mode, TimeShift mode, Basic stabilization mode (in-camera stabilization), Pro stabilization mode (export with Insta360 app/Studio or supported plugins to apply FlowState stabilization)

360:Standard video, HDR video, Timelapse mode, Bullet Time video

Weight

4K: 121g

360: 130.5g

Dimensions (W x H x D)

4K: 72mm x 48mm x 32.4mm

360: 72mm x 48mm x 43mm

Run Time

4K: 4K@60fps - 70 minutes

360: 5.7K @ 30fps - 70 minutes

Video Bitrate

100Mbps

Gyroscope

6-axis Gyroscope

Compatible Devices

Recommended devices： iOS: A11 or above iOS iPhone SE, iPhone 11/11 Pro/11 Pro Max, iPhone XS/XS Max, iPhone XR, iPhone X, iPhone 8/8 Plus Android: Kirin 980 or above (Huawei Mate20, P30 and above) Qualcomm Snapdragon 845 (Samsung Galaxy S9, Xiaomi Mi 8 and above) Exynos 9810 or above (Samsung S9, S9+, Note9 and above) * Devices that do not meet the above requirements can still use the app to control ONE R, however, some operations with high processing performance requirements such as AI supported functions and video playback, may be sub-optimal.

Photo Modes

Standard photos, HDR photos, Burst, Interval photos, Night Shot, PureShot

Live-streaming

Coming Soon

360 live-streaming, FreeCapture Live (user controls visual perspective)

EV

±4EV

Exposure Modes

Photo Shoot Auto, Manual(Shutter 1/8000s-120s, ISO 100-3200), Shutter Priority(1/8000s-1s), ISO Priority(100-3200) Video Shoot Auto, Manual(Shutter 1/8000 - 1/30, ISO 100-3200)

WB

Auto, 2700K, 4000K, 5000K, 6500K

Bluetooth

BLE4.0

Wi-Fi

5G (Standard range of approximately 20 meters)

USB

Type-C

Micro SD Card

UHS-I V30 speed class, exFAT(FAT64) format SD cards with a max storage of 1T are recommended.

Battery Capacity

1190mAh

Charging Method

Type-C

Charging Time

65mins

Use Environment

-4° F to 104° F (-20℃ to 40℃)

Without the cool cameras there would be no cool Airgun videos and so when a company reached out to me and says… Hey, would you like to try out one of our new 4K Action cameras? I say sure! I can always use another high quality 4K camera for even more angles and who knows what else…

In this unboxing video I take a look at the SJCAM SJ10 Pro Action Camera to see what’s in the box obviously, what it looks like and what my first impressions of the SJCAM SJ10 Pro Action Camera are. I have to say the build quality is a lot better than I thought it was going to be, I’m pretty sure the main body is made out of metal and the crips looking lcd screen pretty much takes up the entire back of the camera. The camera is a lot smaller than I was expecting too which is a good thing since the more compact a camera is, the more likely I will be taking it along with me and using it.

Until I get the chance to play around with the SJCAM SJ10 Pro Action Camera fully and see what the quality and functionality are like, here are some of the specifications and details:

• Sensor Brand: Sony IMX377.

• Sensor Type: 7-Layer Glass with 2 aspherical glass lenses.

• Video Resolutions: Up to 4K60fps without GYRO up to 4K30fps with Supersmooth GYRO Stabilization, Slow-motion 2,4,8x.

• Photo Resolutions: 12MP (4000×3000 4:3) 10M (3648×2736 4:3) 8M 16:9 (3840×2160 16:9) 8M 4:3 (3264×2448 4:3) 5M (2595×1944 4:3) 3M (2048×1536 4:3) 2MHD (1920X1080 16:9.

• Video Format: MP4 (H.264 / H.265 HVEC).

• Wifi: 2.4 Ghz 802.11 a/b/g/n.

• GYRO Stabilization: Inner Six-Axis Gyroscope.

• Digital Zoom: 8x.

• Battery Capacity: 1300 mAh Detachable Battery.

• Battery Duration (Approx.): 140 Minutes at 1080P 95 Minutes at 4K60fps (Front screen and Wifi off).

• Microphone (Audio In): Dual Stereo Microphones.

• Back Screen: 2.33" UHD IPS SuperSensitive Touch Screen with SJCAM UI.

• Storage supported: Up to 128GB micro SD high quality 10 class and higher memory cards.

View fullsize

The following product review for the Comica WS60 UHF Dual Mini Wireless Microphone Combo has nothing to do with Replica Airguns but as a YouTuber with a couple of YouTube channels, I have to make sure I not only have good quality video but also good quality audio when I make a YouTube Video for one of my channels.

After all if it sounds like I’m in a wind tunnel or the bat cave and you can not hear clearly what I’m saying then it can be very distracting for you the viewer to understand what I ‘m trying to share with you!

View fullsize

Perhaps you can also utilize a product like the Comica WS60 UHF Dual Mini Wireless Microphone Combo for your audio and video needs, which could also be for something social media related or even just for your own personal use to get the best quality home video and audio.

For the last couple of years I have been using a lapel mic more and more in my videos and I try to use one whenever possible since the audio is just so much better than the Microphone audio built into the camera. It's not that the camera mics are really all that bad, the problem is that most of the time the camera is simply not close enough to the person speaking so you tend to get a lot of background and room noise which makes the speaking audio sound distant with noticeable ambient noise and echo.

View fullsize

Generally I have been using a wired lapel mic that I record directly into my SmartPhone, which I place in my pocket while recording. I use a different camera to record my vide, I then sync the audio to the video in post production on my computer but this requires a bit of audio and video software know how. The advantage to a wireless setup is that you can record directly into the camera if it supports an audio input meaning no more requirements to sycn audio later and no long cord bwteen the audio source and the camera. A wireless setup usually is more compact and versatile. What I like about the Comica WS60 UHF Dual Mini Wireless Microphone Combo is the fact that it comes with two lapel mics that both have their own transmitter so they can be worn independently by two separate people, perfect for conducting interviews or even when you simply need a mic in more than one location.

View fullsize

In this Comica WS60 UHF Dual Mini Wireless Microphone Combo YouTube Video Review I first unbox the Comica WS60 UHF Dual Mini Wireless Microphone Combo and show you what you get inside the box and talk about some of the basic features and specification. I then test it out and record audio so you can hear for yourself what it sounds like. I first test it plugged into my SmartPhone like I normally do and then I pug it into my DJI Osmo Pocket for a second reference test. Please keep in mind I performed my original testing without monitoring the real time audio output so I did not catch that there was some interference from my overhead LED lighting. I was able to change the channels on my Comica WS60 UHF Dual Mini Wireless Microphone Combo and completely remove the background bussing I was getting from the LED lighting in my room.

View fullsize

Here are some basic Details and Specifications for the Comica WS60 UHF Dual Mini Wireless Microphone Combo.

System:

• Wireless Transmission: Digital UHF

• Number of RF Channels: 24

• Included Transmitters: 2 x Body pack with Microphone

• Diversity: Non-Diversity

• RF Frequency Band: A: 568.125 to 579.125 MHz - B: 580.125 to 591.125 MHz

• RF Bandwidth: 11 MHz

• Max Operating Range: 196.9' / 60 m (Line of Sight) - 98.4' / 30 m (with Obstruction)

• Latency: <40 ms

• Encryption: None

• Modulation: FM

View fullsize

Receiver:

• Form Factor: Camera-Mount / Portable

• Mounting Options: Shoe-Mount, Tabletop (with Included Hardware)

• Antenna: 1 x Internal, Fixed

• Number of Audio Channels: 2

• Audio I/O: 1 x 1/8" / 3.5 mm TRS Female Unbalanced Line Output - 1 x 1/8" / 3.5 mm TRS Female Unbalanced Headphone Output

• Frequency Response: 20 Hz to 18 kHz

• Network I/O: None

• Word Clock I/O:None

• USB/Lightning Connectivity: 1 x USB Type-C (Bus Power, Charging)

• Approximate RF Sensitivity: -83 dBm

• Power Requirements Battery or Bus Power (USB)

• Battery Type: 3 x AAA (Not Included)

• Approx. Battery Life: 4 Hours

• AC/DC Power Adapter: 5 VDC (Not Included)

• Display & Indicators: 1 x Back-Lit LCD (Battery Status, Channel, Data Transmission, Group, Level, RF Level) - 2 x LED (Data Transmission)

• Operating Temperature: 32 to 122°F / 0 to 50°C

• Storage Temperature: -4 to 140°F / -20 to 60°C

• Dimensions: 4.1 x 2.6 x 0.7" / 104 x 65.2 x 18 mm

View fullsize

Transmitter:

• Form Factor: Body pack with Microphone

• RF Output Power: 10 mW

• Audio I/O: 1 x 1/8" / 3.5 mm TRS Female Unbalanced Input

• Pad: None

• Muting: Off/On Switch

• Signal Processing: High-Pass Filter:

• Sync Method: Manual

• Antenna: 1 x Internal, Fixed

• Power Requirements: Battery or Bus Power (USB)

• Battery Type: 3 x AAA (Not Included)

• Approx. Battery Life: 4 Hours

• USB/Lightning Connectivity: 1 x USB Type-C (Bus Power, Charging)

• Display & Indicators: 1 x Back-Lit LCD (Audio Level, Battery Status, Channel, Group, High-Pass Filter, Mute, RF Output Power) - 1 x LED (RF Output Power)

• Operating Temperature: 32 to 122°F / 0 to 50°C

• Storage Temperature: -4 to 140°F / -20 to 60°C

• Dimensions: 4.1 x 2.6 x 0.7" / 104 x 65.2 x 18 mm

View fullsize

Microphone:

• Form Factor: Lavalier

• Color: Black

• Sound Field: Mono

• Output Connectors: 1 x 1/8" / 3.5 mm TRS Male Unbalanced

View fullsize

Packaging Info:

• Package Weight 2.055 lb

• Box Dimensions (LxWxH) 9.7 x 7.3 x 4"

Make sure to watch my full YouTube Video Review for the Comica WS60 UHF Dual Mini Wireless Microphone Combo:

Again I have some new products to show everyone. Some we got a bit of a preview of when I was at SHOT Show 2019 earlier this year but now I have them in my hands to show off and of course will be doing full Table Top and Filed Test for anything new as soon as I can get to them.

View fullsize

Starting with Sig Sauer, they sent me their brand new Sig Sauer P365 CO2 Blowback BB Pistol. This was probably one of my favorite new Air Pistols at SHOT Show simply because it is so small and somehow Sig was able to find a way to put a full size drop out metal magazine that holds both the CO2 and BB’s in it. This is one I am really looking forward to testing out in the Indoor Sea Can Airgun Shooting Range.

View fullsize

Another fantastic product is Crosman’s DPMS Full Auto CO2 BB Rifle which was pretty much perfect the first time around. Well at SHOT Show this year Crosman updated it a bit mainly with some cosmetic changes and now is offering the Crosman MPW, a slightly shorter version of the DPMS and now with an AR Compatible Stock for customizing your Crosman’s MPW Full Auto CO2 BB Rifle.

View fullsize

Yet one more item I was drooling over at SHOT Show 2019 where the Air Venturi Springfield Arms XDM Air Pistols being offered in GBB Airsoft and CO2 BB models along with 3.8 and 4.5 inch versions. It looks like the GBB Airsoft venisons where first out of the factory and I was able to get them in two styles, the Air Venturi Springfield Arms XDM 3.8 GBB Airsoft and Air Venturi Springfield Arms XDM 4.5 GBB Airsoft.

View fullsize

So maybe not as exciting… I also take a look at a NBB CO2 BB Makarov from KWC that is pretty basic but is much less expensive and will offer higher FPS and more shots per CO2 being that it is Non-blowback Airgun. It will be interesting to see how it compares performance wise to the KWC Full Blowback CO2 BB version.

View fullsize

Last but also super cool and I know it’s not really as Airgun related but still something I think everyone will be interested in is the Pocket Shot Pro Arrow Pouch with D-Loop. I reviewed the Pocket Shot “Slingshot” a while back, this new product allows you to use standard Arrows with their new Arrow Pouch getting around 40 pounds of pull and it comes with a trigger release. By the way the Pocket Shot Pro Arrow system is legals to hunt deer with in most US States, I’m not sure about Canada but perhaps here too?

View fullsize

It’s been long time coming but here is the last bit of my journey to get my 1993 Ducati 750 Super Sport licensed and on the road! I know not everyone is going to be interested in a motorcycle video since this is an Airgun channel but a lot of people did mention to me that they wanted to know more about my Ducati and how it was all going. Besides even if you have never owned a motorbike they are super cool to look at and listen to :)

View fullsize

In this “Getting the 1993 Ducati 750 Super Sport on the Road” YouTube video I go through the final process I need to do to get my Ducati 750ss registered and licensed for road use. This final step requires me to get BC Vehicle Inspection done where an authorized mechanic inspects the vehicle to make sure it complies to all the road use standard in place here in Canada BC.

View fullsize

You may want to go back a few months and see where this all started but for now come along with me and watch and see if I make this happen?

In this December Update Video I wish everyone a Merry Christmas and Happy New Year. If you have other beliefs and perhaps don’t celebrate Christmas in the traditional Canadian fashion then I wish you a Happy Holiday!

I received a number of products lately and really don’t have time to do full reviews of them as the Holliday season is on us which is going to limit how many videos I can pump out over the next couple of weeks so hopefully this Update video will keep everyone excited about the future Replace Airgun Videos.

Here are the items I talk about in this December 2018 Update Video:

View fullsize

Sig Sauer ASP M17 CO2 Blowback Pellet Pistol

• Buy Sig Sauer Airguns in Canada

• Buy Sig Sauer Airguns in the US

View fullsize

Sig Sauer Fake Suppressor for P226 ASP Pellet Pistol

• Buy in Canada

• Buy in the US

View fullsize

Umarex Steel Strike Full Auto BB Rifle

• Buy in Canada

• Buy in the US

View fullsize

ROHM RG-89 .380 Caliber Blank Revolver

• Buy in Canada

• Buy in the US

View fullsize

Umarex Legends WildCard Airsoft SAA Revolver

• Buy in Canada

• Buy in the US

View fullsize

Umarex WW2 Limited Edition P08 CO2 Blowback BB Pistol

• Buy in Canada

• Buy in the US

View fullsize

Umarex WW2 Limited Edition M712 Full Auto CO2 Blowback BB Pistol

• Buy in Canada

• Buy in the US

View fullsize

Webley Mark VI CO2 Pellet Revolver

• Buy in Canada

• Buy in the US

View fullsize

John Wayne Signature SAA Revolver Solid Maple Wood Case

• Buy in Canada

• Buy in the US

View fullsize

You may be asking why a Airgun channel is doing a review of a hand-held microphone. Well part of making good video is also making sure you also record great sounding audio! It doesn't matter how Hi-Def the video is, if you can't hear what I'm saying because the audio is all muffled or drowned out by background sounds then you aren't getting much out of the video.

View fullsize

I have done some other audio product reviews before for similar reasons, I figure some of my viewers and followers may also be interested in making their videos sound better even if it's only a home video. When FiFine approached me a second time to review a product for them I quickly asked if I could review their FiFine KO26 Wireless Hand-held Microphone for those time when I do an interview styled video like at SHOT Show!

In this video review for the FiFine KO26 Wireless Hand-held Microphone I show you what comes in the box and also test out the audio quality while making the video. You will hear various samples of audio from three different recording sources in this video. I start the video out using my Sure Lapel mic while I'm showing you around the FiFine KO26 Wireless Hand-held Microphone, then I briefly switch over to my camera audio and then I finish with the FiFine KO26 Wireless Hand-held Microphone to see how it sounds.

View fullsize

Here are some of the key features and specification for the FiFine KO26 Wireless Hand-held Microphone:

• 2 YEAR NO QUESTIONS ASKED WARRANTY.

• Dynamic Mic with Cardioid pickup pattern. Uni-directional pattern & fine-tuned integrated circuit ensure optimal background noise rejection.

• Frequency response 50-18KHz guarantees clarity of your vocals.

• Metal construction.

• USB 2.0 receiver with headphone jack serves as an external sound card for audio output and monitor.

• Works on Mac, PC, Chromebook, (iOS and Android devices - Require adaptor).

• UHF (Ultra High Frequency 565-584 MHz) gets longer range and more powerful signal than Bluetooth up to 80 feet away even with obstacles.

• 20 selectable frequency channels ensures no problems with interference.

• Easy-to-read LCD screen to indicate battery life and frequency channel.

Since the new home for my Italian addition to the Sea Can Indoor Airgun Shooting Ranges is now situated in my gun range area, I figure you are going to see it beside my airgun target and start asking me about it. So I figured I would make a video all about it and let you know before hand. I do plan on moving the new addition to its permanent home in my garage but while I’m doing a bit of initial work on it and since my garage is in need of some reorganizing, it will have to stay in the sea can for now…

View fullsize

A while back I did review of the 1/4 Scale Mini Replica Guns distributed by Goat Guns. Goat Guns sent them to me for review and at the time we where not selling them in our Replica Airguns Store. Recently we got some of our own 1/4 Scale Mini Replica Guns that I would say are pretty much exactly the same as the Goat Gun Line but with different packaging since they are not distributed by Goat Guns.

View fullsize

The good news is you can get the same product from us now in our Canada and US Replica Airguns Stores! And ours are even pre-assembled for you but if you like you can take them apart similarly to a real gun.

These 1/4 Scale Mini Replica Guns are made out of a lot of metal where you wound find it on the real steel counterpart and most parts operate the same too like removable magazines, working triggers and safety’s, Even the dust covers on the M4’s open when you charge the mini gun!

View fullsize

We carry several models:

• M4A1 RIS 1:4 Scale Model Rifle Display

• M4A1 Digital Camo 1:4 Scale Model Rifle Display

• AK47 1:4 Scale Model Rifle Display

• M83 Sniper 1:4 Scale Model Rifle Display

• L115 Magnum Sniper 1:4 Scale Model Rifle Display

View fullsize

What? Another Drone? Is Replica Airguns becoming a drone review channel... No I am not going to be reviewing drones as a habit but I did decide to upgrade my Yuneec Breeze 4K to a DJI Spark for a number of reasons.

Reason number one it's a DJI and they simply make some of the best Drones you can buy for the money. The main reason I ultimately went with the DJI Spark is because it just takes better quality 1080p Video which is what I'm after. It does this because it has a dedicated 2 axis mechanical gimbal that smoothes out the video even before the internal stabilization gets to it and make the video look even smoother so the end video output is incredibly smooth!

View fullsize

Some other reasons I feel the DJI Spark Fly More Combo was a better option for me are: It's super small, it was not really a lot more expensive, it has better tracking technology and can even understand hand and arm gestures for flying without even using a remote of any kind. The DJI Spark can fly faster and much farther than the Yuneec Breeze and has a little bit better battery run time.

In this DJI Spark Fly More Combo Unboxing Video I open the box for the first time and take a look at what you get inside. I had not flown the DJI Spark or even checked it out yet so everything is new to me and I am seeing it first hand and for the first time. I can say it is way smaller than I thought it was going to be. Look forward to some cool drone video on the channel in some of my upcoming videos...

View fullsize

What some of you may not think about is all the stuff that goes behind the scenes when a Vimeo video is being made. It's a lot more than simply grabbing a camera and saying what's on your mind although that can work sometimes.

Most of the time multiple cameras are used, tripods and special lighting are important and even how you record the audio source can make a huge difference as to the sound and what people hear in your final video.

With all that said I am always looking for a new way to help me out with the quality of my video recording and production. How can I make things look better or more interesting, how can I improve the sound quality and clarity of my videos?

Well today I show you two new products I picked up that I feel will help me out in these areas. First in the audio department I show you my new Wireless Headset/Lapel Mic system from a company called FiFine Technology. They actually sent me their FiFine Wireless Headset and Lapel Mic for free so thanks a lot for that! My plan is to use the FiFine Wireless Headset and Lapel Mic to record the audio portion of my videos rather than the built in mic in my camera since I will get less room noise and better direct voice audio recording. I think it will also be useful when doing outside shooting videos to get super clear audio with less outside noise at all times. For this testing I simply connected the FiFine Wireless Headset and Lapel Mic to my Samsung Android phone using a USB adaptor, the same can be done suing an iPhone.

View fullsize

Moving on now to a new video product, I have been wanting to get a Drone to capture more interesting video that I can shoot from multiple viewing angles and also be able to have a moving camera while I shoot outdoors videos. The problem is they can be kind of expensive for anything decent, because of this, so far I have not been able to justify bitting the  bullet and buying a drone. That was until I saw a great deal on the Yuneec Breeze 4k Selfie Drone at my local Best buy for half price ($249 CAN) What a deal!

Anyways, watch me fumble around while I try to figure things out with my Yuneec Breeze 4k Selfie Drone for the first time, there is always a learning curve when you get something new but I do hope to be able to utilize both of these new products in upcoming videos for everyone.

View fullsize

I've already made a Table Top Video Review for the Pocket Shot Slingshot so make sure to check that video review out for details on the product and some nice closeup video.

I have been wanting to get outside and test out the Pocket Shot Slingshot since I was not confident in my skills and didn't want to shoot inside the See Can Indoor Shooting Range. Well today was the day and the weather was pretty much perfect, just a little bit overcast but still warm enough for some shorts and a light shirt, my kind of weather!

The overcast lighting helped me get some good Chronograph FPS readings for the 1/4 inch and 3/8 inch Steel Ball ammo I was using for my testing. The 1/4 inch Steel Ball was around 16 grain and I was able to get an FPS reading of around 270 feet per second, this gave me a foot pound energy of 2.66 foot pounds using the 1/4 inch Steel Ammo.

View fullsize

Stepping up to the heavier 3/8 inch Steel Ball Ammo, the FPS did drop a bit down to about 244 feet per second. Since the 3/8 inch Steel Ball are heavier at almost 55 grain, the Foot Pound energy went up to just over 7 foot pounds so more than double the energy of the 1/4 inch Steel Ball.

In terms of accuracy, shooting any Slingshot setup is going to come down mainly to the person using it and I am by no means an avid Slingshot user. That said I was able to hit several of the targets I setup about 20-25 feet away with my Pocket Shot Slingshot, some as small as a few inches in diameter so I was pleased with myself for at least hitting something on camera for you all :)

Let me know what you all think of the Pocket Shot Slingshots...

Buy the Pocket Shot Slingshot in Canada.

Buy the Pocket Shot Slingshot in the US.

View fullsize

Todays Video Review is really something different from Replica Airguns but I felt that it might be something that our viewers and customers would find interesting and perhaps consider picking up something like this for themselves down the road? So make sure to let me know what you think and if I get enough positive feedback I'll take a look at getting some of these mini replica rifles in our online store.

View fullsize

The product I am reviewing today are there 1/3 scale replica rifles from Goat Guns. The M4A1, the AK47 and the Tommy Gun. They are non-firing highly detailed mini versions of the real steel guns they are models of. You even build them nearly the same since they come in a kit. All the metal parts you would find on the real steel version are metal in the Goat Guns replicas. You will even find working bolts and triggers, removable magazines, adjustable sights and they even include three small metals bullets you can load into the magazine.

View fullsize

If you're a gun person I'm pretty sure you will die these highly detailed miniature non-firing replica rifles from Goat Guns and the price is really not that bad considering what you get, only about $30-$40 US.

We carry several similar models in our Replica Airguns Canada Store:

• M4A1 RIS 1:4 Scale Model Rifle Display

• M4A1 Digital Camo 1:4 Scale Model Rifle Display

• AK47 1:4 Scale Model Rifle Display

• M83 Sniper 1:4 Scale Model Rifle Display

• L115 Magnum Sniper 1:4 Scale Model Rifle Display