One of the most common types of question I get on my Replica Airguns YouTube channel has to be something like… Why is my Airgun not working? Most of the time the amount of info about the problem is limited to something like… “It was working yesterday but now it’s not working anymore” or something like “when I pull the trigger nothing happens”. My personal favorite is… “I took my gun apart and now it doesn’t work!”

I just made a similar video for Blank Guns and as I said in that video, trying to trouble shoot a mechanical or technical problem over the internet is very difficult, this goes for cars, guns, computers or what have you…

In this Why is My CO2 Airgun Not Working video I will however cover some of the more common and obvious problems I have seen relating to why a CO2 Airgun may not be working properly. I really don’t get a lot of questions about Spring Piston or Pump Airguns so I will be focusing on CO2 Airguns in this video. There will be a lot of crossover with CO2 Airsoft guns so this video may be helpful for some of you Airsofters out there

First let’s get the super obvious stuff out of the way! 

• Did you put a new CO2 cartridge in it and is it pierced all the way?

• Did you load BB’s or Pellets into the Airguns magazine and is the magazine in the gun correctly?

• Is the safety off?

• If the gun is a blowback semi auto single action Airgun then did you pull the slide back prior to the first shot?

CO2 Related Problems:

Not all CO2 cartridges are created equal, they often have slightly different shaped nubs on them and some brands will work better than others in different Airguns. If the shape of the CO2 nub does not fit properly into the valve area then it may not pierce or it could pierce but then not allow you to tighten it all the way losing all the CO2 in the process. If the CO2 is coming form the airguns handle to CO2 Valve area then this is an indication that your problem is related to the area where the CO2 enters the airgun.

There is a seal where the CO2 cartridge buts up to the valve, this seal can be damaged or even deformed from usage or even leaving your CO2 in the gun for too long. The outside CO2 Valve seal can also take the shape of a specific CO2 nub so when you use a different brand CO2 the seal may not properly make concat with the new CO2 type you are using, again causing leaking or even the total loss of all your CO2. Watch my YouTube video on “How to Fix Leaking CO2 in an Airgun”.

CO2 Valve Related Problems:

Again, make sure that Outside CO2 Valve Seal is in good condition and any leaking is not being caused by this problem, if you have checked the Out Side Seal and everything is OK with it then perhaps there is a problem with the CO2 valve?

One indication that your CO2 Valve might be the culprit is the total loss of all your CO2 when you try to insert and tighten a new CO2 Cartridge. Usually all the CO2 will exit the barrel, not the handle or valve area. What may be happening is the valve is stuck open or the internal seal is broken or deformed. If this is the case you will have to remove the valve and have a look inside, this is a lot easier on CO2 airguns that have the CO2 valve in the magazine, if the CO2 valve is in the actual Airguns then a lot more disassembly may be required and I would recommend an Airgun technician take care of this for you.

If the gavel is in the magazine then you will have to unscrew it, you may require a special tool for this? Once the valve is out of the magazine  take a look inside and examine the internal seal, also look for any bits of metal shavings as they can disrupt the action of the valve causing leaking. Give the inside of the valve a good clean and then lubricate it with some silence spray. hopefully that fixes your problem!

BB’s getting Stuck in the Blowback Gas Tube:

I have actually made a dedicated video for this problem so I will put a link to it in the description of this video. The main reason people may have this problem is because we all like to rack that slide on our full blowback Airguns, but if you have a fully loaded magazine then each time you reach that slide without shooting the gun, you are inadvertently trying to load another BB into the breach area, the breach is only designed to hold one BB at a time so after a few racks of the slide the newly loaded have no place to go but into the Gas Tube where they can get stuck and cause having to the operation of your Full Blowback CO2 Airgun.

BB’s Rolling Out of the Barrel of Your CO2 Airgun:

This is not actually a fault of the gun but happens because of the way the gun is designed. This situation can happen with certain CO2 Airguns when the gun user pulls the trigger really slowly while the gun is point slightly in a downward position. What is actually happening is the first part of the trigger is made to draw a BB from the magazine into the breach of the gun. If the barrel of the gun does not have a rubber hop-up stopper in it then the BB is free to roll down the barrel and out of the gun. How do you fix this problem? Be more committed to your trigger pull and or shoot at a target that is not so low. Perhaps place your targets slightly higher than the gun so the barrel is not pointing down, especially if you like to take your time with the trigger :)

A Little Maintenance Can Go a Long Way!

Sometimes a good cleans is all you need to do to get things working as they should, again I have already made video Tutorial Showing “How to Clean Airguns and Blank Guns”.

What about stuff like My Airgun is jammed or my trigger is stuck or some random part fell out of my gun?

There is only so much I can cover in this video, most other problems are going to get a bit more complicated to fix and I suggest if your Airgun is not working and the suggestions I have made in this video do not solve your problem, then consider taking your gun into a gun tech.

First off I want to say it’s hard to trouble shoot technical or mechanical problems over the internet regardless of if ithas to do with guns, cars, computers or pretty much anything where unless you are there in person it’s really hard to figure out the problem.

But I will attempt to address some of the more common issues why a blank gun may not be functioning properly.

Why is my Semi Auto Blank Gun Not Cycling or Ejecting Shells?

One very common reason a blank gun may not be cycling the shells properly is because the owner has removed the barrel restrictor plug. People usually do this to make the barrel opening look more realistic but the barrel restrictor is a necessary component to increase the back pressure allowing the slide to cycle fully to the rear position so it can eject and pickup a new shell.

The blanks you are using may not have enough gun powder in them. Some blank guns require banks with more gun powder than others, again this additional internal pressure forces the slide all the way back, if the blank does not have enough gun powder in it then only a partial slide motion happens and so the discharged shell may not eject properly, in this case the user would have to clear the blank gun manually so another shell can then be picked up and loaded into the breach.

If your blank guns is dirty or not lubricated then it may act sluggish again restricting the full movement of the slide which will effect correct operation. Make sure to thoroughly clean and lubricate your blank gun, that may be a quick fix for you!

You may have a faulty extractor? The extractor is like a hook that grabs the discharged shell while the slide is in the reward position pulling or extracting the shell out of the breach. If the extractor is worn or broken then the empty shell will not be ejected from the breach so when a new shell is picked up from the magazine it has nowhere to go and usually you will get a jam-up in the ejection port area.

One final situation that can cause your blank gun to not cycle properly is to strong of a slide spring, some blank guns out of the box just come with a really heavy slide spring, so much so that even blanks with lots of gunpowder in them are still not strong enough to make the slide operate full motion. Your only option here would be to replace the heavy slide spring with a lighter one.

Why Are My Blanks Not Firing?

This is a situation where you pull the trigger and nothing happens. Lets get the obvious causes right out of the way here… Did you put blanks in your gun and are they new blanks? Did you chamber the first round in your semi auto pistol?

So now that that’s out of the way let’s look at some other reasons why your blank gun may not be firing a blank. Perhaps the firing pin is broken? Most blank guns are not made out of carbon steel and even the firing pins can be lesser quality than what you would find in a real gun so blank guns are more prone to breaking than real guns. I have seen broken firing pins in blank guns first hand so make sure to check the firing pin and that it is fully operational.

Try changing up your blanks to another brand? Again blank gun ammunition is not made to the same higher standards that real firearm ammo is made and some primers may require a little more pressure than your gun is providing. Even with real guns an ammo change may help the gun operate better.

Why is the Trigger or Hammer Not Operating Properly?

I have come across blank guns where there are mechanical problems in the trigger and hammer areas, you may be able to address this yourself but I would recommend taking your blank gun to a gunsmith since you will have to take the gun pretty much full apart to fix a problem in the trigger and hammer areas.

Of course make sure your gun is clean and lubricated, this can help a lot with the mechanical areas of your blank gun.

One problem I saw with a few EKOL Special 99’s was specifically with the single action potion of the trigger, when I would pull the hammer back it would not lock back and the hammer would often slip and fire randomly, this is rather dangerous. When I took the gun apart I found that the table top or step that the trigger was supposed to catch on was worn down on the edge so it would simply slip off. I was able to fix this by filing a new edge on the step area. Again this can happen because blank guns are not made out of as high quality metal materials as real guns.

Why does the Flame Come out the Top of My Blank Gun and Not the Front?

If you find that the flame or discharge comes out of the top of your blank gun and not the barrel, this usually does not mean anything is wrong with your blank gun. All it means is you own a top venting blank gun and not a front firing blank gun. In some countries front firing blank guns are not allowed but front venting blank guns are. The same may also be reversed in some countries, for instance here in Canada we can only import front firing blank guns with flare adaptors since our blank guns are imported under the assumption that they are to be used as signaling or flare devices.

Can I Convert my Top Venting Blank Gun into a Front Venting Blank Gun?

I really don't recommend altering a blank gun in any way as it may be a violation of your local laws and it could cause the blank gun to malfunction in a very bad way causing serious injury or even death!

In theory I suppose it may be possible to convert your Top Venting Blank Gun into a Front Venting Blank Gun but again you would need to allow for just the right amount of back pressure so a wide open barrel would not work unless it was a revolver. You can not simply remove the red plug and bingo you have a front firing blank gun because in most cases the barrel will be completely plugged in the frontal region. Not only would you need to drill out the plugged portion of the barrel but you would also have to somehow fill in the top venting area and again makes sure to allow for just enough back pressure to cycle the slide back and forth.

Hopefully this has helped some of you with blank gun issues. If you’re looking for a blank gun make sure to come down to www.ReplicaAirguns.ca and www.ReplicaAirguns.us and have a look in our blank gun area of our online stores.

Power:
Generally speaking a longer barrel is going to allow for more power. If you compare most CO2 pellet pistols to CO2 Pellet Rifles, you will find that the CO2 Pellet Pistol will generally shoot about 300-400 fps using a standard lead Pellet. On the other hand many CO2 Pellet Rifles can get up to as high as 600 fps which is much better speed for humanly shooting some smaller pests.

If you are talking about Springer or Variable Pump Air Pistols versus their Air Rifle counterparts, again the Air rifles will generally shoot with much more power. I have seen some none CO2 Air Pistols shoot up into the 500-600 fps range but again compered to none CO2 Air Rifles, they can even double these numbers.

Some of you may ask about Steel BB Pistols and Rifles. I personally would never really sue this type of ammunition for pest control simply because most BB Rifles have much less raw power than Pellet Rifles and steel BB’s will not be as accurate at any type of longer distance.

Stability:
When holding any rifle from the shoulder, you have three point of contact with your body spread out in a much longer distance than a two handed pistol grip. Holding steady even without a rested position is much easier using a rifle. Even when using a rested position, the rifle will more stable.

Accuracy:
A big factor in accuracy is stability but there are also other factors to consider. Barrel length its self does not make the gun more accurate, you only need a few inches of barrel length to get constant accurate results from a gun. What makes longer barreled guns more accurate is the distance between the rear and front sight. The closer the sights are together, the more margin for error there is, the longer you spread out the sights from each other, the more accurate the sighting system becomes.

Overall More Humain:
When you consider Air Rifles tend to have higher power, better accuracy and overall more consistency than shorter barreled Air Pistols. The logical choice for humanly shooting a Pest is to use the Air Rifle. The last thing you want to do is make any animal suffer, even if it has been causing a lot of havoc around your home or farm or place of business.

I already made several review videos for both Gletcher NGT (4.5mm Steel BB) and the Gletcher NGT R (.177 Cal Pellet) Revolvers, including table top and shooting videos. So make sure to check those videos out for more information on both versions of Gletcher NGT and NGT R Revolvers.

I did however miss some noteworthy details that I wanted to cover in this video. Firstly, the real steal Nagant M1895 Revolver this Gletcher NGT is styled after has a very unique gas-sealing system that the Airgun version does not replicate or really require but it is worth mentioning.

Here is some more info on how the original Nagant M1895 Revolver Gas Seal System works:

(From Wikipedia) The M1895 by contrast, has a mechanism which, as the hammer is cocked, first turns the cylinder and then moves it forward, closing the gap between the cylinder and the barrel. The cartridge, also unique, plays an important part in sealing the gun to the escape of propellant gases. The bullet is deeply seated, entirely within the cartridge case, and the case is slightly reduced in diameter at its mouth. The barrel features a short conical section at its rear; this accepts the mouth of the cartridge, completing the gas seal. By sealing the gap, the velocity of the bullet is increased by 15 to 45 m/s (50 to 150 ft/s.) This feature also eliminates the possibility of injury through the dangerous expansion of gases from the cylinder behind the barrel, which are easily capable of severing a finger if the user holds the gun incorrectly (with a finger positioned in front of the cylinder during fire) - a noted safety-issue in conventional revolvers.

Moving on to some of the features incorporated into the Gletcher NGT NGT-R CO2 BB and Pellet Revolver that I did not point in any of my previous videos. There is an extractor rod that can be used to extract a shell, this is not really necessary on the airgun version since the shells do not expand and tighten on the cylinder as they would n the real steal Nagant M1895 Revolver built is nice that we can replicate this feature with the Airgun version. You can also remove the cylinder completely from both the BB and Pellet shooting Gletcher NGT NGT-R CO2 Revolvers. The cylinder is actually very heavy and adds a lot of weight to this compact 7 shot Revolver.

It is always nice when an Airgun is built in such a way that it replicates the real steal version as closely as possible and the Gletcher NGT NGT-R CO2 BB and Pellet Revolvers do this nearly perfectly.

Buy Gletcher NGT Revolvers in Canada

Buy Gletcher NGT Revolvers in the US

I get asked on a daily bases form many of my Vimeo Viewers about how and if there is a way to get rid of the White lettering on Airguns, Typically people are wanting to remove the intrusive Warning instructions from Airguns like the Cybergun Tanfoglio Witness 1911, the Cybergun/Swiss Arms GSG 92/P92 and many other CO2 Replica Airguns that have lettering or branding that you may want to get rid of.

In this Instructional Tutorial Video I show you how can at least tone down the white lettering and even completely remove it on some Airguns without damaging the Airguns finish underneath the white lettering. You will have to use some patience and perhaps repeat this method a few times but the end result is worth the effort.

The magical product I use to remove the white lettering on many popular Airguns is a product from Birchwood Casey called the Presto Gun Blue Pen. This product is actually designed to touch up real steel gun in areas where the blueing has worn off, lucky for us the Birchwood Casey Presto Gun Blue Pen also works well to remove the ugly white lettering from Airguns.

I have often been asked which of the Shells for the Shell Loading Revolvers work in which Shell Loading Revolvers? After all many of them look a lot alike so can you mix and match Shells for the various types of Shell Loading Revolvers?

In this Vimeo Instructional Video I test out a bunch of Shells to see which ones actually will work or not work in several of the most popular Shell Loading Revolvers.

Some of the Shell Loading Revovers Tested in this Instructional Video are:

• Dan Wesson Classic Revolver (BB, Airsoft, Pellet)

• Dan Wesson 715 Revolver (BB, Airsoft, Pellet)

• Colt Single Action Army Peacemaker (BB, Airsoft, Pellet)

• Gletcher NGT and NGT-R (BB and Pellet)

• Webley Mark VI (BB)

• KWC 357 / Umarex 357 (BB, Airsoft)

• G&G G731 (Airsoft) 

Type: Airsoft Rifle.

Manufacturer: KJWorks

Model:KP-02 Version 2

Materials: Metal and Nylon Fiber build.

Weight: 5.84 Pounds (2650 Grams).

Barrel: 13 inch metalnon-rifled smooth bore.

Propulsion: Green gas or 12 Gram CO2 dependant on magazine used.

Action: Blowback,Single action only.

Ammunition Type: 6mm plastic Airsoft BB's.

Ammunition Capacity: 29 rounds.

FPS: 410-440 fps

Trigger Pull: The trigger pull on the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is pretty much exactly like a real Ruger 10/22, nice and short, not to light or heavy, crisp and single action only. If you already have a Ruger 10/22 and want to pickup this Airsoft version for some anytime shooting then you will not be disappointed in the trigger since it is already what you are used to.

Accuracy: I decided to setup my paper target a little further out than my standard 30 feet, so I took it back to around 50 feet and put around 24 shots into it in a fairly quick succession from a rested position. The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine grouped continently and well centred on target getting around a 3 inch grouping. This was using a red dot scope but with the out of the box hop-up setting in place. I was a little bit surprised by my fps results as my Chronograph recorded an impressive 445 average 5 shot fps using the lower powered green gas magazine. All shot where within only a few fps of each other too! I can only imagine how hard this gun would shoot using the alternative CO2 Magazine. Blowback action was just enough to give some feedback and of course allowed for the bolt to cycle giving the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine a true single action trigger pull.

Build Quality: The build quality for all KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is very good with a nice weight and feel to it, It really does feel like I am holding a real Ruger 10/22 and it is one of the most popular semi auto 22LR rifles out there for a reason. Mechanically this Ryger 10/22 copy works great, super consistent and very responsive. The fit and finish as with all KJWorks guns is top notch.

Realism: The KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine is for all intents and purposes simple an Airsoft version of the Ruger 10/22 and even though I have no way to confirm this, I would imagine many 10/22 after market accessories may actually work with the KJWork 10/22 Gas Blowback Airsoft Carbine. Everything works just like it would on a real 10/22 without the loud noise and ejecting shells.

Available in the:Replica Airguns Store

Pros:

• Built on the very popular 10/22 platform so lots of people are going to be very familiar with this rifle and may want an Airsoft version they can shoot just about any time they feel like it.

• Good weight and feel to it.

• Blowback semi auto action with true single action trigger.

• Lots of rail access points for tons of add on accessories.

• Pop-up fully adjustable sights stay out of the way but are ready to go when needed.

• Easy to adjust Hop-up.

• Available magazines in both CO2 and Green Gas.

• Adjustable AR styled rear stock with AR pistol grips.

• Sling mounts included.

• Works with standard Airsoft screw on flash hider or suppressors.

• Awesome FPS and consistency.

• Very accurate even at 50 feet, around a 3 inch 25 shot grouping.

Cons:

• No full auto mode.

• Higher capacity mag would have been nice.

• Would be nice to have a higher capacity magazine for it.

Comments:

I am really impressed with the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine! It feel and shoots a lot like the real steel version but with less noise and recoil. For back yard shooting fun and practice you can not find a cheaper gun out there to simulate shooting your real 10/22 and of course this rifle used on an Airsoft field would be a perfect fir for almost any shooting environment since it is light, compact, accurate and powerful. I think I found my newest favorite Blowback Airsoft Rifle :)

My Vimeo Table Top  Review of the KJWork KC-02 Version 2 10/22 Gas Blowback Airsoft Carbine:

Buy the KJWork KC-02 V2 10/22 Gas Blowback Airsoft Carbine in Canada

In this 2016 SHOT Show Interview I talk with Chip Hunnucutt from Crosman Corporation. Chip was eager to show off Crosman's new Airbow which is a essentially a hybrid PCP Air Rifles combined with a Crossbow. SO take away the bow and replace the power source with a 3000 PSI compressed air system that is capable of shooting standard archery arrows at 450 fps with 160 foot pounds of energy using 375 grain arrows.

The Crosman Airbow on a full 3000 PSI charge can deliver 8 consecutive shots @ the regulated 450 fps. The Airbow also weighs in at 7 pounds and being that it is a Bullpup design it is only 33.5 inches long so nice and compact for an arrow shooter.

Since the power is generated by the PCP compressed air system there is no heavy cocking rope so a simple lift of the ambidextrous cocking bolt is all that is needed to charge the Crosman Airbow. The Airbow also comes standard with a CenterPoint® 6x40 mm scope specially designed with the Airbow in mind.

Since the Crosman Airbow is technically an under 500 fps airgun, it should be considered an uncontrolled firearm here in Canada which means no PAL license will be required to buy and own the Crosman Airbow in Canada. In terms of using the Airbow for hunting as it is not a bow but rather an Airgun, that is yet to be determined here in Canada.

In this 2016 SHOT Show Interview I talk with Dani Navickas from the Airgun division of Sig Sauer. Dani and I discuss Sig's new line of CO2 Blowback Pellet rifles and pistols. Dani talks about some of the behind the scenes information that went into the development and manufacturing of Sig's new line of CO2 Airguns.

Sig CO2 P226 and P250 Air Pistols along with their Sig MPX and MCX Air Rifles have been developed in house by Sig.Sig has been working very closely with a Japanese manufacturer to make sure that every stage of development is to Sig's high standards. The new Sig CO2 Blowback rifles and pistols are made to match the real steal version in almost every way including dimension, weight, functionality, materials used and even trigger pull.

Sig's new Sig MPX and Sig MCX Pellet Rifles have a brand new patented belt fed 30 round pellet magazine that is indexed via the internal blowback action of these rifles smoothing out the trigger action. The Sig P226 and Sig P250 pistols use a double ended 16 round pellet magazine similar to what you would find on Umarex's PX4 Strom blowback pellet pistol.

Look for Sig's new line of CO2 Blowback Pellet Airguns coming out shortly.

This is my SHOT Show 2016 Teaser Video! You will get to see some new gun highlights from companies like Umarex, ASG, Crosman, Sig Sauer, KWA and ISC. I will be following up this video with some interview videos very soon so do make sure to check back for those uploads. All I can say about the show is it’s huge! So much to see, so much walking and too much to take in…

ASG:

As always, ASG had some new products this year. The all new Dan Wesson 715 357 Magnum shell loading Revolver! This gun feels absolutely amazing in the hand and will be available in Steel BB, Airsfot and even Pellet shooting versions. Also new are the CZ P-09 and CZ 75 SP-01 Shadow Full Blowback BB and Airsoft Pistols.

Crosman:

Big at Crosman this year was their PCP Airbow, Crosman put a lot of focus on this product and even had a lot of crossbows on display to go with their new PCP Airbow. Crosman also introduced their low cost entry level Benjamin Maximus PCP rifle in .177 and .22 calibers offerings. Not really much in the way of replica pistols from Crosman this year, but then again last year was kind of the same?

Sig Sauer:

I finally made it to the Sig Sauer Booth this year to checkout their new CO2 Pellet gun line. All new Sig Airguns are made true to size and weight with similar trigger actions as their real steel versions. The Sig MPX is their more compact (shorter barreled) pellet shooting CO2 rifle with internal blowback and belt fed 30 round magazine. The Sig MCX is the longer barreled rifle version but built much the same as the MPX. Sig also introduced two new pellet shooting CO2 Blowback Pistols, the P226 and the P250. Both use similar double ended rotary magazines as the Umarex PX4.

Umarex:

Umarex always seems to have some new exciting Airguns products to offer at SHOT Show. The PPK is back with a few updates including no more ugly CO2 tab sticking out of the bottom! And yes the Beretta Model 92A1 will finally be shipping soon, I believe in February! My favorite product this year from Umarex would have to be the Full Blowback, Full size drop out magazine S&W M&P 40 CO2 BB Pistol. Umarex released yet another 1911 on the market, this version does come with a stick mag and sports pretty high fps and more shots per CO2 then the KWC based 1911’s. The super popular Colt SAA Revolver is now available in a pellet shooting version with a rifled barrel :) Umarex had on display another low cost revolver, the ultra futuristic looking Brodax CO2 BB Revolver.

KWA:

KWA always has really nice high quality products to showoff at there booth each year, we may even start carrying some of KWA's products this year, fingers crossed on that one… New to the KWA line are some AEG rifles with simulated blowback action, I really liked the Blowback AEG AK they had on display. KWA also released a new Airsoft shell loading revolvers that had some of the nicest looking brass and aluminum shells. On display under a glass cover was a very solid Gas Blowback Thompson Machine-gun with real wood stock, it was absolutely gorgeous!

ISC:

ISC known for their top quality AEG internals, had their full line of high quality Airsoft rifles on display. And new this year to ICS was their first ever Airsoft pistol, the blowback BLE Alpha. The BLE should be out mid year and looked and felt really nice. The trigger on it was super short and light.

I have some really awesome Interview videos I’m working on, I will be uploading them shortly so stay tuned for those…

With the popularity of the KWC - Cybergun 1911 Blowback CO2 Pistols and how super realistic they are in so many ways, it is no surprise that people often ask me if they can replace the original grips with grips made for a real 1911.

The short answer is yes you can! You will have to be prepared to remove just a little bit of material from the backside of both grips near the bottom of the handle where there is an area that has been flared out to accommodate the CO2. Not really a big deal, you can use a Dremel for the quick and easy approach or even some sand paper if you don't mind taking a little more time.

In this Vimeo Video I demonstrate using grips that fit a real 1911 and show you just exactly where you will need modify them to fit on the KWC and Cybergun CO2 Blowback 1911 pistol series.

Buy the KWC Blowback CO2 1911 BB Pistol in Canada

Whether you like it or not, most of us have come across an Airgun with an ugly orange tip on it at some point. In most cases you will find the intrusive orange or red tips on Airsoft guns that shoot plastic BB's, in some cases you will even find them on Airguns that shoot either lead pellets and/or steel BB's.

It really comes down to where you live as to what your local gun laws have determined is required for your area. You may even live in a region where Airguns and Airsoft guns are not allowed at all! So for you a red or orange tip on the front would be welcome if it would allow you to own an Airgun or Airsoft gun. What about the entire gun being painted a bright color, well that is the case for some folks so again having a red or orange tips may not be as bad as it originally seemed...

In Canada where I live, we used to only be allowed Airsoft guns that had clear sections as our replica gun laws are very strict and all black Airsoft guns would have fallen iinto the "replica" category if they did not have large clear plastic see-through sections on them. This clear section law was revised somewhat over the last several years to allow for all black Airsoft guns here in Canada. It was determined that many Airsoft guns with higher fps limits could cause a serious injury to a human, making them less of a toy in the eyes of the law and more of a weapon. Because of this, Airsoft guns that are capable of shooting a .20 gram plastic BB at a velocity of 360 fps or "higher" are now considered to be similar in the eyes of the law to a regular steel BB or lead pellet shooting Airgun. In Canada, Pellet and Steel BB guns are actually considered firearms of a sort so this allows the higher fps Airsoft guns to be all black since it can not be a replica of a firearm if it is in fact considered to be a firearm by law.

The long and short of all of this is that here in Canada we do not require our Airsoft guns to have orange or red tips since they are considered more or less to be just like any other Airgun and our Airguns do not have red or orange tips either.

Getting back to the title of this article "No Orange Tip On Your Airsoft Gun! Are You Insane?" I often get folks from the US giving me heck for removing the orange tips from my Airsoft guns or asking me why my Airsoft guns don't have them in the first place. These people even state that I could get in a lot of trouble for this! Perhaps they think I live in the US or that US laws govern Canada as well? I am not sure but I can say for the record that I am not breaking any laws at least here in Canada where I live.

I know in the US that wholesalers and retailers by law have to sell Airsoft guns with the affixed orange tips on them, once the end user receives that gun and depending on which state they live in, it may or may not be legal to remove the orange tip. Again, you will need to look into your local state laws as they are different from state to state in the US.

I don't often review target and or hunting rifles since for the most part Replica Airguns is all about well... replica airguns :) I have reviewed some of my own personal spring piston and pump rifles since I have them and there is a cross over in folks that like both the replica airguns and airguns meant for target and or hunting purposes.

We do have a small selection of spring piston rifles in our Replica Airguns Canada store suitable for target and small game so I thought I would point some of them out in this preview video.

Daisy 1938 Red Ryder BB Rifle

• Type:BB rifle

• Manufacturer: Daisy

• Model: Red Ryder.

• Materials: Stained solid wood stock and forearm, leather saddle thong.

• Weight: 2.2 pounds.

• Barrel: 10.85 inches, smooth bore.

• Propulsion: Spring.

• Action: Lever Action.

• Ammunition Type: 4.5mm Steel BB's.

• Ammunition Capacity: 650 rounds

• FPS: 350.

Ruger Explorer Youth Air Pellet Rifle

• Type: Pellet rifle.

• Manufacturer: Ruger

• Model: Explorer.

• Materials: All-weather composite black stock, metal.

• Weight: 4.5 pounds.

• Barrel: 15 inches, rifled

• Propulsion: Spring piston.

• Action: Break barrel.

• Ammunition Type: .177 caliber lead pellets.

• Ammunition Capacity: 1 round.

• FPS: 495.

Ruger Air Hawk Combo Pellet Rifle with 4x32 Scope

• Type: Pellet rifle.

• Manufacturer: Ruger

• Model: Air Hawk.

• Materials: Wood, metal.

• Weight: 8.16 pounds.

• Barrel: 18.7 inches, rifled

• Propulsion: Spring piston.

• Action: Break barrel.

• Ammunition Type: .177 caliber lead pellets.

• Ammunition Capacity: 1 round.

• FPS: 495.

Browning Leverage Pellet Rifle with 3-9x40 Scope

• Type: Pellet rifle.

• Manufacturer: Browning

• Model: Leverage.

• Materials: Wood, metal.

• Weight: 8.6 pounds.

• Barrel: 18.9 inches, rifled

• Propulsion: Spring piston.

• Action: Under lever.

• Ammunition Type: .177 caliber lead pellets.

• Ammunition Capacity: 1 round.

• FPS: 490.

Browning Gold Series Synthetic Pellet Rifle with 3x9x40 Scope

• Type: Pellet rifle.

• Manufacturer: Browning / Umarex

• Model: Gold Series.

• Materials: All-weather composite black stock, metal.

• Weight: 8.4 pounds.

• Barrel: 14 inches, rifled

• Propulsion: Spring piston.

• Action: Break Barrel.

• Ammunition Type: .177 caliber lead pellets.

• Ammunition Capacity: 1 round.

• FPS: 495.

Buy Daisy 1938 Red Ryder BB Rifle in Canada

Buy Daisy 1938 Red Ryder BB Rifle in the US

Buy Ruger Explorer Youth Air Pellet Rifle in Canada

Buy Ruger Explorer Youth Air Pellet Rifle in the US

Buy Ruger Air Hawk Combo Pellet in Canada

Buy Ruger Air Hawk Combo Pellet in the US

Buy Browning Leverage Pellet Rifle with 3-9x40 Scope in Canada

Buy Browning Leverage Pellet Rifle with 3-9x40 Scope in the US

Buy Browning Gold Synthetic Rifle in Canada

Buy Browning Gold Synthetic Rifle in the US

It has been way too long since I got to go to the gun range and shoot my "big boy" guns! I say that sarcastically, sure my real steel guns are fun to shoot but it sure costs a lot of money and basically all we really do is shoot paper targets. Shooting at papper targets is fun for a while but I kind of enjoy shooting my airguns at pretty much any type of target I choose to shoot at. And of course any time I want to and for pennies per shot.

So getting back to Range Day shooting my real steel big boy guns ;) I went with a couple of buddies of mine and we shot a nice variety of guns. My Norinco NP-30 double stack 45 cal 1911, my Wyoming Arms Parker 10mm, a couple of my friends Glock 40 cals, my Norinco NP-34 P228 and Norinco Tokarev Type 54 9mm pistols, my Chiappa 1911-22 and ISSC M22 22LR pistols, a nice Sig Mosquito 22LR, my buddies S&W M&P 15-22 22LR rifle along with my ISSC MK22 SCAR 22LR rifle and my friends mighty custom Ruger Mini 14 in .223 caliber...

It was a cold day but a really fun day and it gave me a chance to really use my iPhone 6 plus camera for its slow-motion capabilities in a decent lighting situation.

Enjoy the footage of these "real guns" shooting in real time and slowed down.

Since I have already doen dedicated reviews for both the T.A.C Converter and XBG BB Pistol, I won't drag this written reviw on too long since yuo can read my other dedicated reviews for each product.

In a nutshell, when you buy the Umarex T.A.C. Converter XBG CO2 BB Pistol Combo, you get the XBG CO2 4.5mm BB Pistol preinstalled in the T.A.C Converter, you also get the included fore-grip which is renovable by the way can coudl be used stand alone on any other gun with an under barrel Picatinny rail.

Keep in mind that this combo kit only works with the XBG Pistol since there are no included adaptors for the other Umarex pistols designed to work with the T.A.C Converter. (H&K USP, S&W M&P40, XBG, CZ Enforcer, Walther P99 DAO, SA177).

The addition of the T.A.C. Converter to the XBG really improves the shoot-ability since the rear folding stock allows for a much more stable hold position. You also have the addition of whit dot sights front and back with the rear sight being adjustable for windage only. I would recommend a compact light weight red dot sight for this gun since using the included open sights are hard to keep in focus because of how close the rear sight ends up being to your eyes when in the shouldered position.

With the top, bottom, and side picatinny rails you can add litterally all types of accessories to this package including a tac light, laser, optical sight, red dot, folding metal sights to name a few.

The XBG BB Pistol has a nice combincation of 400+ fps with tuns of shots per CO2 and respectible accuary with easy access to the Drop out metal BB magazine.

For under $60 in our Canada Replica Airguns store this is a really fun package!

Buy the T.A.C. Converter XBG Combo in Canada

Buy the T.A.C. Converter XBG Combo in the US

While the weather is still holding on, I setup some clay pigeon targets at varying further out distances than the typically 30 feet I shoot on my deck. I paced out approximately 40-60-80-100+ foot ranges conservatively thinking this would be a good test to see if a 6mm Airsoft rifle could effectively hit targets at any of these ranges using heavy .36 gram Airsoft BB's.

Make sure to checkout my other video I shot on the same day that features my Baikal Drozd Blackbird taking it through this exact same long range shooting test.

So today I brought out an Airsoft Sniper rifle since this is what it's made to do, the model being the ASG AW .308 Airsoft Sniper. As with many of my shooting videos I captured all the fun using a bunch of different cameras and camera angles along with a dedicated lapel microphone so the audio also comes in nice and clear.

So make sure to watch my YouTube video and see how the ASG AW .308 Airsoft Sniper Rifle does shooting clay pigeons up to 100 Plus feet away...

Buy AW .308 Airsoft Rifle in Canada

Buy AW .308 Airsoft Rifle in the US

If you have been watching my Full Auto Fun Videos, then you will have noticed that I have recently been using Clay Pigeons as my go-to targets. Generally Clay Pigeons are shot from launchers and used with shotguns since the flight of the Clay Pigeon simulates a bird in flight nicely.

So I thought, why not use them as reactive targets for my Airguns and Airsoft guns? It turns out they work pretty darn good, well at least with 4.5mm Steel BB pistols and I would imagine even better with pellet guns. What about Airsoft guns, will the Airsoft lighter weight plastic BB's have enough mass to get the job done?

You'll have to watch this video to find out the answer to that question when I unload a full magazine of .20 gram Airsoft BB's into some Clay Pigeons using my KWC .50 Desert Eagle...

Buy KWC Airsoft Desert Eagle in Canada

Buy KWC Silver Desert Eagle in Canada 

Perhaps the last of my 4.5mm Steel BB Dull Auto Fun Video? We'll see? Today I take out my Umarex EBOS (Electric Burst of Steel) 8 Round Burst BB Machine Gun and again take aim at a bunch of clay pigeons I set up 30 feet away. Even thought the EBOS does not have the highest rate of fire with only 500 rounds per minute, it does get the job done because it stays true on target and really proved to be very accurate allowing me to even trim off the smallest bits of clay pigeon stuck in the edges of the holders.

The rate of fire on the Umarex E.B.O.S. almost reminds me of what you would hear or expect from an AK 47 type machine gun.

Near the end of this video I try my luck at shooting some of the clay pigeons out of the air shotgun style but failed horribly :( Perhaps I should give by modified 1200 rounds per minute Drozd Blackbird a go at it :)

Buy BB guns in Canada  

Buy BB guns in the US

A very common occurrence with CO2 Airguns and Airsoft guns are leaky CO2 seals. Usually this occurs right where the CO2 cartridge connects to the main valve area. This can be either in the gun or in the magazine depending on the setup of the airgun.

There are many reasons why this can happen, but the most common reasons are a worn-out or dried up seals or even a seal that has been imprinted or misshapen from the constant pressure of the tip of the CO2 pressing against it.

When this happens you may encounter a leaking CO2, the severity of the leak can vary from mild slow leaks to leaks that can be so bad that the gun is unusable. Keep in mind there can be other problems not related to the CO2 seal such as in the valve area, the fix I show you in this YouTube video will not fix a leaking valve, you can try using something like Crosman Pellgun oil for a problem like that.

Watch my below Vimeo video where I show you how you can easily use some Plumbers Teflon Tape to improve the contact points between your CO2 and CO2 main seal and eliminate leaking CO2 in your Airgun.

A very common question I get asked is "How Long Can I Leave CO2 in My Airgun?" So what do I do when I get asked a question over and over again... Well I make a video and give you my answer to the question.

Some CO2 Related Questions I seem to get over and over again are:

1. Can I leave an unused CO2 in my Airgun and for how long is it safe?

2. Can I reuse a C2 once it is empty?

3. Can I use my gun without CO2?

In this YouTube video I address questions 1 and 2, I kind of forgot about question number 3 since it is not as often but it does come up from time to time believe it or not and the answer to being able to use a CO2 airgunwith out CO2 is "NO", It's kind of like trying to drive a car without gas, or turn on a light without electricity or stay alive without food...

So anyways, watch my below Vimeo video for answers to questions one and two: