In this Field Test Shooting Video I test out Crosman’s latest version to the 357 line of CO2 Revolvers and perform both my Velocity and Accuracy test using both .177 caliber Lead Pellets and 4.5mm Steel BB’s to see which ammo has better velocity/power and is most accurate. Also make sure to watch my Table Tope Video Review where I go ver specifications and features and show the Crosman Vigilante CO2 Pellet and BB Revolver up nice and close.

Starting with the velocity portion of my Indoor Field Test Shooting video I placed a brand new 12 gram CO2 into the Crosman Vigilante CO2 Pellet and BB Revolver and tested out some 7 grain .177 caliber Lead Pellets. I was able to average 389 fps in what I would consider normal indoor temperature ranges so you can expect a bit higher velocities in outdoor weather conditions. Moving on the 4.5mm 5.1 grain Steel BB’s, I averaged a bit lower at 360 fps which may seem confusing since the Steel BB’s are lighter than the Lead Pellets? The Lead Pellets fit the barrel much more snug stoping any CO2 from getting around them which helps increase the fps over the Steel BB’s which are a hard metal and need to be slightly smaller in diameter and therefore do let some CO2 get by reducing the pressure behind them.

For my accuracy porting of the the Indoor Field Test I was going to place 6 shots from each magazine into my paper target setup 30 feet down range but ended up using all 10 rounds for the pellet magazine, perhaps because I was just having too much fun :) Since the BB magazine only holds 6 rounds my shot grouping for BB’s only included 6 shots so keep that in mind for the final results. All said and done the Lead Pellets outperformed the Steel BB’s once again getting about a 1.5 inch grouping over the 2.5 inch grouping for the Steel BB’s. And I know the Crosman Vigilante CO2 Pellet and BB Revolver is more than capable of getting a .5 to 1 inch grouping from previous Field Tests I have made using similar 357 type Crosman Revolvers.

The Crosman Vigilante CO2 Pellet and BB Revolver is just one of those must have old school classic Air Pistols I think everyone should own at least some sort of version of. I do like the look of the Vigilante barrel with it’s more modern and aggressive design and functional top and bottom rails for adding on accessories. The ability to choose what ammo type you want to shoot is also a plus and the price point is bang on for a nice CO2 Air powered Revolver.

• Buy the Crosman Vigilante CO2 Pellet and BB Revolver in Canada

• Buy the Crosman Vigilante CO2 Pellet and BB Revolver in the US

View fullsize

Type: Pellet & BB Revolver
Manufacturer: Crosman
Model: Vigilante
Materials: Metal and Plastic.
Weight: 2 pounds (908 grams).
Barrel: 6 inches rifled.
Length: 11.36 inches.
Propulsion: CO2 x 1
Action: Revolve , single and double action trigger.
Ammunition Type: 4.5mm Steel BB's / .177 caliber Pellets.
Ammunition Capacity: 6-BB / 10-Pellet round rotary magazines.
FPS: 465-BB’s / 435-Pellets.

View fullsize

Trigger Pull: The trigger pull on the Crosman Vigilante CO2 Pellet and BB Revolver is rather nice in single action with virtually zero take-up and it has a not too light weight with a predictable feel to it. In double action it does get much longer and heavier but still very usable. If you have larger thicker finger then you may want to start off in single action as the finger opening is a bit tight.

View fullsize

Accuracy: I have not specifically tested out the Crosman Vigilante CO2 Pellet and BB Revolver so far but I would be very surprised if it was any different than the standard Crosman 357 I tested back in 2012. Other than the shape of the outer barrel, both of these guns are virtually the same including the frame and the 6 inch barrels. Back in 2012 when I tested out the Crosman 357 I averaged 402 fps using 6.9 grain pellets and was able to get a 1 inch multi-shot grouping at 30 feet away from my paper target. Not sure if this was the entire 10 round mag or not? I will be making an update Field Test Shooting Video so we will see if I can replicate these results with the Crosman Vigilante CO2 Pellet and BB Revolver.

View fullsize

Build Quality: The Crosman Vigilante CO2 Pellet and BB Revolver is a fairly basic pistol that incorporates a plastic outer barrel and inner steel barrel, the grips are also plastic as expected and so are the magazines and sights. Most everything else is metal including the receiver, trigger and hammer. This line of Crosman 357 pistols has been around for decades so you can expect hours of fun and reliable shooting with it.

View fullsize

Realism: There are for sure a lot more realistic looking Revolvers out there with swing out cylinders that except shells just like their real steel counterparts but where the Crosman Vigilante CO2 Pellet and BB Revolver shines is in performance. You will get more shots per CO2, higher fps and better accuracy with the Crosman Vigilante CO2 Pellet and BB Revolver over other more realistic Revolvers on the market.

View fullsize

Pros:

• Inexpensive Pellet revolver with a proven track record that goes back decades.

• Good usage of metal parts where you need them most. (Metal  trigger, hammer, frame, barrel, CO2 Tab screw

• Single and double action trigger for action and more focused shooting.

• Excellent accuracy and good power with a reasonable amount of shots per CO2.

• Fully adjustable rear sight.

• Can mount a bunch of accessories on the picatinny barrel top and bottom rails.

• CO2 and CO2 tab are nicely hidden and use all metal.

• Comes with both a Pellet and BB magazine.

View fullsize

Cons:

• Outer barrel is plastic but very solid. Metal would have added a bit more weight and perhaps better balance?

• Grips and trigger pull length may be a bit long for smaller handed people when shooting in double action.

• Not your most realistic revolver in terms of replicas out there but I would say more usable than most.

• No white dots on the sights.

View fullsize

The Crosman Vigilante CO2 Pellet and BB Revolver is basically a reskinned Crosman 357 at the end of the day but I have to say it is my favorite looking Crosman 357 out there with its aggressive barrel design. And the added bonus are the top and bottom Picatinny rails which make for mounting accessories like Red Dots, Lasers and Tac Lights super easy! if you’re looking for function over realism at a price point that is more than fair then pick yourself up one of the Crosman Vigilante’s from our Replica Airguns Store!

• Buy the Crosman Vigilante CO2 Pellet and BB Revolver in Canada

• Buy the Crosman Vigilante CO2 Pellet and BB Revolver in the US

I made a video a little bit ago talking about how Canada’s new Bill C-21 will affect pretty every gun owner in Canada including even airgun owners of BB, Pellet Airsoft and even Paintball Guns. Make sure to watch that video first called Bill C-21 Canada is Going After Your Red Ryder BB Gun.

This video is all about how you can get involved in making some waves by signing two online petitions along with contacting your local Member of Parliament and letting them know your disapproval of Bill C-21 and all that it imposes on law abiding Canadian gun owners.

Probably the most important online petition to sign would be the House of Commons Petition E-3201 Bill C-21 so make sure to sign that one!

The other online e-petition we need to sign is the change.org petition.

And lastly but also super important is to send an email to your local member of Parliament again let them know your disapproval of Bill C-21. I have included a link to the web[age where you can locate your local MP and below that is a template of what you could include in your email to them.

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

Dear (MP),

I am a constituent in your riding. I am writing to you to voice my concerns over the new provisions that were announced under the proposed Bill C-21, and how this will impact myself, my community and many other Canadians.

"Criminal Code 1 (1) The definition replica firearm in subsection 84(1) of the Criminal Code is replaced by the following:

replica firearm means any device that is designed or intended to exactly resemble, or to resemble with near precision, a firearm that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules, and that itself is not a firearm, but does not include any such device that is designed or intended to exactly resemble, or to resemble with near precision, an antique firearm; (réplique)

(2) Section 84 of the Act is amended by adding the following after subsection (3.1): Certain firearms deemed to be prohibited devices

(3.2) For the purposes of sections 99 to 101, 103 to 107 and 117.03, a firearm is deemed to be a prohibited device if

(a) it is proved that the firearm is not designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second or at a muzzle energy exceeding 5.7 Joules; and (b) the firearm is designed or intended to exactly resemble, or to resemble with near precision, a firearm, other than an antique firearm, that is designed or adapted to discharge a shot, bullet or other projectile at a muzzle velocity exceeding 152.4 m per second and at a muzzle energy exceeding 5.7 Joules."

Make sure to also sign ePetition e-3201 to put a stop to Bill C-21:

https://petitions.ourcommons.ca/en/Petition/Sign/e-3201

View fullsize

I often have people ask me what is more powerful in terms of one gun over another and which Airguns have more raw power, BB versus, Pellet, versus Airsoft, versus Paintball?

Well in this indoor field test shooting video I compare all of the above head to head to see which Airgun not only has the most raw power but also how well they perform on a target setup 30 feet down range since after all what does it matter how powerful a gun is if it can not hit the target!

The Airguns I used in this head to head shooting performance test where as follows:

• EKOL ES 55 Non Blowback 4.5mm BB Pistol

• Umarex Desert Eagle Blowback .177 Cal. Pellet Pistol

• Cybergun Desert Eagle Blowback 6mm Airsoft Pistol

• Umarex T4E TR50 .50 Cal. Paintball Revolver

Keep in mind the ammunition for each Airgun is very different not just in terms of materials but also their weight which will have a big effect on the energy they produce. For example for this test I used 4.6 grain 4.5mm Steel BBs, 4.6 grain 6mm Aluminum Airsoft BB’s. 6.9 grain .177 cal. Lead Pellets and 17.7 grain .50 cal. Rubber Paintballs.

Watch my YouTube Video to see how well each Airgun did in this comparison shooting test!

View fullsize

Perhaps you might call this a followup video since I already made a full Field Test Shooting Video of the all black version of this pistol and you may wonder if the color of a gun could in some way effect how it performs? Well I don’t think color would really matter but it has been over 6 years since I did my original Field Test Shooting video fo the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver and so perhaps some things have changed, maybe my shooting is better or worse? At any rate let’s find out.

Also make sure to take a look at my Table top Video for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver if you're interested in the specifications and details along with some nice tight close up video of the Airgun.

Starting off with my Chronograph test I was able to get an average 6 shot velocity of 348 fps which is about 40 fps less than my testing 6 years ago of 390 fps, perhaps the temperatures where a bit different? Perhaps the valve setups of the guns was not the same? By the way the temperature was 23 degrees Celsius in the indoor Airgun Sea Can Shooting Range and I was using a brand new 12 gram CO2 along with 5.1 grain zinc coated steel BB’s.

View fullsize

Moving on to the accuracy test, surely I would get a similar 1 inch 6 shot grouping from the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver, after all it’s been 6 years and I must be a much more advanced shooter… Well there again the Chrome Umarex Colt Python 357 Magnum CO2 BB Revolver did not perform as well as the black one from my 2014 Field Test? Again maybe the steel BB’s I was using where not of the same quality? Maybe I simply had one too many espresso shots? As the video shows this time around I was only able to get about a 2 inch 6 shot grouping from the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver. Still not bad but I was hoping for better result or at least the same as before.

I could do this test again and get completely different results using perhaps another brand of CO2 on a warmer day with higher quality Steel BB’s and just maybe with me on my game a little bit better? At the end of the day 350 fps is perfectly fine for putting holes in pop cans and a 2 inch group at 30 feet will get you on most targets every time so I’m not going to sweat it too much. If you are looking for a shell loading CO2 BB Revolver the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is for sure one of my top picks.

• Buy the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver in Canada

• Buy the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver in the US

View fullsize

Type: BB air revolver
Manufacturer: Umarex.
Model:  Colt Python 375
Materials: Almost entirely all Metal.
Weight: 2.75 pounds (1218 grams).
Barrel: 5.5 inches, metal non-rifled.
Propulsion: 12 gram CO2.
Action: Revolver, single & double actions.
Ammunition Type: 4.5mm steel BB's.
Ammunition Capacity: 6 round cylinder.
FPS: 400.

View fullsize

Trigger Pull: The trigger pull on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is good in both single and double action, it’s nice that you have the shorter lighter single action trigger for slower more accurate shooting but you can also blast away in double action when you feel like it. The hammer on the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver is firm with not very much wiggle which some other revolvers in this category do have.

View fullsize

Accuracy: Based on my results shooting the Umarex Colt Python 357 which is essentially the same gun in a different finish. The results I got shooting my 6 round group from a 30 foot out semi rested position where good overall. Vertically there was about a 2 inch spread while horizontally there was about a 1 inch spread. I did find the plastic tips on the brass shells seemed to be a bit tight at first and this is when I did most of my Chronograph and target shooting. I believe the tightness effected the consistency of the FPS which also effected the accuracy especially up and down. I did get one shot out of the Umarex Colt Python 357 well over the claimed 400 fps but again the fps was rather erratic most likely because of the snug BB fit due to shell break-in.

View fullsize

Build Quality: The Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver being mostly metal has a very good build quality and is on par with the Dan Wesson 715 shell loading revolver. It has a nice weigth adn balance to it and feels really good in the hand! The only real plastic I could find was in the grips and the shell tips. Fit and finish was also good with no noticeable chrome wear or sloppy workmanship. It will be interesting to see how the Chrome finish wears over time compared to the black finishes fodun on most KWC made Airguns.

View fullsize

Realism: TheUmarex Colt Python 357 Magnum Chrome CO2 BB Revolver overall is a close copy a the real steel Colt Python 357 styled revolver. I did notice the rear portion of the receiver (between the rear cylinder and hammer) to be a bit longer perhaps to accommodate the CO2 valve length, but other than that, this pistol is super close to the original Colt Python 357 styled revolver it is based on. Again being all metal gives this CO2 BB revolver very realistic weight and feel and the loadable brass shells make using this gun almost exactly like using a real shell loading revolver but for much less cost per shot and of course a lot less recoil on the hands and noise to be had.

View fullsize

Pros:

• Shells loading revolver give you the feeling of loading and shooting a real revolver.

• Mostly all metal design.

• Lots of detail, well made, chrome looks nice, not sure if it will wear better than the black finish found on most KWC made pistols?

• Good overall weight, almost 3 pounds.

• Should have good overall power, accuracy and shots per CO2 (based on my previous Colt Python testing).

• Fully adjustable sights.

• Well hidden CO2 Screw.

• Recessed barrel.

• Nice Trigger pull in both single and double action.

Cons:

• Grips are a bit rough and wood grain is only OK.

• Grips may be a bit large for people with small hands.

• Decent enough Colt Python 357 replica but the frame is a bit long between the cylinder and the hammer.

View fullsize

Comments:

It’s been a while since I reviewed a Shell Loading Airgun and this one is pretty much the same Airgun I have reviewed in the past in both the KWC and Umarex Distributed forms. It has been almost 6 years since I took a look at one on my table and it still hods up today. I plan on performing another Field Test Shooting Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver to see if I can replicate the same good results I did back in 2014 when I tested it out on my deck. If you’re looking for a shell loading revolver in the 357 design then for sure checkout the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver as an option.

My Vimeo Table Top Review for the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver:

• Buy the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver in Canada

• Buy the Umarex Colt Python 357 Magnum Chrome CO2 BB Revolver in the US

View fullsize

Type: Pellet Revolver.
Manufacturer: Gamo
Model: PR-776.
Materials: Mostly metal construction.
Weight: 2.2 Pounds (1 kg).
Barrel Length: 6 inches
Total Length: 11.5 inches.
Propulsion: CO2 x1
Action: Revolver single and double action.
Ammunition Type: .177 caliber pellets.
Ammunition Capacity: 8 rounds per magazine.
Max FPS: 400+ fps.

View fullsize

Trigger Pull: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver has your traditional revolver single and double action trigger setup. In double action, the trigger is going to be a bit longer and heavier but it feel fairly smooth with no real friction points and I would consider it to have a medium trigger pull. When you cock the hammer back placing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in single action, the trigger pull becomes very short with virtually no take-up at all and the weight of the trigger is very light allowing for more accurate shots.

View fullsize

Accuracy: Make sure to watch my Field Test Shooting video for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I test out the velocity and accuracy in the Replica Airguns Indoor Airgun Shooting Range. In summary the Gamo PR-776 CO2 .177 Caliber Pellet Revolver shot a little bit hotter than claimed at just over 400 fps using around 7 grain lead pellets. In terms of accuracy with a total of 16 shots the grouping spread out to around 4 inches but I am pretty sure a different pellet choice may have made a difference.

View fullsize

Build Quality: The build quality of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver is pretty good overall. It is mostly all metal with the exception of the grips of course, Fit and finishes looks good, everything feel snug adn tight with the exception of the pistol grips. I feel like the grips could easily move out of place and get caught on something. This is not a problem when shooting, more so when in a holster. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver feels good in the hadn't, nice and solid and with a good weight to it.

View fullsize

Realism: The Gamo PR-776 CO2 .177 Caliber Pellet Revolver is a decent looking Airgun in the style of a traditional revolver, I wouldn’t say it’s an exact replica of any specific revolver in production but it does tick off all the boxes in terms of looking realistic. The weight and feel for now and the Gamo PR-776 CO2 .177 Caliber Pellet Revolver also has a recessed barrel and hidden CO2 crew. The only real giveaway would be the cylinder size as it is a bit smaller than expected and of course is chambered for .177 caliber pellets.

View fullsize

Pros:

• Good power over 400 fps using actual lead pellets.

• Quicker reloading over shell loading revolvers

• More shots per magazine reload, 8 versus 6.

• Comes with two metal 8 round magazines.

• Traditional single and double action trigger.

• White dot front sight with fully adjustable rear sight.

• Good weight and feel to it.

• Fit and finish look good.

• Recessed barrel for realistic looking barrel opening.

• Should be able to use a dovetail type scope mount for adding on a red dot or magnified scope.

Cons:

• Not a fan of the loose pistol grip setup to access the CO2.

• Was hoping to get a bit tighter grouping but may have been a pellet choice issue.

View fullsize

Comments:
It was nice reviewing the Gamo PR-776 CO2 .177 Caliber Pellet Revolver as it was a bit different then most of today shell loading revolvers. I like that the Gamo PR-776 CO2 .177 Caliber Pellet Revolver still offered a realistic looking cylinder that the shell loading revolvers have but with the moon clip style magazines that allow for quick adn easy reloading of 8 rounds at a time. The velocity or power of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver was even a bit high than Gamo claims using PBA Platinum pellets since Gamo claims 400 fps using these 5.1 grain lead pellets. My testing with closer to 7 grain pellets yielded fps up and over 400 fps. All the Gamo PR-776 CO2 .177 Caliber Pellet Revolver needs is to be just a little bit more accurate but I feel this may simply be more of a pallet choice, once you find a pellet the Gamo PR-776 CO2 .177 Caliber Pellet Revolver likes I am pretty sure it will deliver accurate shots.

My Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver:

• Buy the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in Canada

• Buy the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in the US

View fullsize

Make sure to watch my upcoming Table Top Review for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where I go over the specifications, pros and cons and show it up nice and close. In this Field Test Shooting Video I determine what the accuracy and velocity of the Gamo PR-776 CO2 .177 Caliber Pellet Revolver by testing out the fps with my Chronograph along with a accuracy test shooting a paper target at a distance of 30 feet away using a rested shooting position.

View fullsize

For the velocity test I placed a brand new CO2 Cartridge in the Gamo PR-776 CO2 .177 Caliber Pellet Revolver and shot five 6.9 grain lead pellets though my Chronograph. Gamo claims their 5.1 grain PBA Platinum pellets will shoot around 400 fps so I was expecting something in the low to mid 300’s but was surprised at a five shot average of 4115 fps with the much heavier RWS6.9 grain pellets. The slowest shot I achieved was 396 fps while the fastest shot was 434 fps. The temperature was right around 24 degrees Celsius or 75 degrees Fahrenheit.

View fullsize

For the next section of my Field Test Shooting Review I setup a brand new paper target 30 feet down range and loaded up two eight round magazines. The results for the Gamo PR-776 CO2 .177 Caliber Pellet Revolver where a bit confusing with both eight round magazines. It seemed like most of the shots wanted to group within about 1-2 inches of each other but I was getting several outliers that extended the grouping to closer to four inches. Not the best performance but as I have found with many guns, sometimes you need to find a pellet that the gun is happy with. the wrong pellet can really make a difference and I am fairly sure this was the case with the Gamo PR-776 CO2 .177 Caliber Pellet Revolver using the RWS pellets. just not the best choice for it.

View fullsize

The Gamo PR-776 CO2 .177 Caliber Pellet Revolver overall performer well, like I said I really think pellet choice will be the deciding factor in how accurate it is going to be. The velocity was very good for a CO2 Pellet revolver considering I was suing actual lead pellets and not the alloy pellets Gamo was using as their reference. The Gamo PR-776 CO2 .177 Caliber Pellet Revolver uses metal eight round magazines which are easy to preload and allow for two additional shots over the more common these days shell loading revolvers, which makes the Gamo PR-776 CO2 .177 Caliber Pellet Revolver more practical as a target pistol allowing for more power and easier loading.

• Buy the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in Canada

• Buy the Gamo PR-776 CO2 .177 Caliber Pellet Revolver in the US

View fullsize

Gamo PR-776 CO2 Pellet Revolver

• .177 caliber Pellets

• 8 round rotary magazines x2

• 12 Gram CO2 x1

• 6 inch rifled barrel

• Fixed white dot front, fully adjustable rear sight

• 2.29 pounds

• 400 fps

• Buy in Canada

• Buy in the US

View fullsize

Gamo P-900 IGT Pellet Pistol

• .177 caliber Pellets

• Break Barrel single shot

• Gas piston (IGT)

• 6.25 inch rifled barrel

• Fiber optic front, adjustable rear sight

• 1.3 pounds

• 400 fps

• Buy in Canada

• Buy in the US

View fullsize

Umarex REKT OPfour CO2 Dart Rifle

• Nerf Darts 30% faster / 30% farther

• Pump action

• CO2 x2

• 12 round removable magazine

• Peep sights

• Adjustable rear stock

• 90 fps

• Buy in Canada

• Buy in the US

View fullsize

JAG Arms Scattergun Green Gas Airsoft Shotgun

• 6mm Airsoft BB’s

• 28 round shotgun shell magazines x6

• Green gas or propane

• Pump action 3 /6 round burst

• Pop-up front and back iron sights

• 6-7 pounds

• 360 fps

• Buy in Canada

• Buy in the US

View fullsize

If you have not already checked out my Table Top Video for the Umarex T4E TR50 .50 Caliber Paintball Revolver then make sure to do so for specifications and a closer look at it.

The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball pistol, it has a very different look and also uses .50 caliber Paintballs which are a little bit less common than the .68 and .43 caliber paintball gun I have been reviewing up until now. The Umarex T4E TR50 .50 Caliber Paintball Revolver is some countries is marketed as a self defense gun but those versions do have a little bit more fps and foot pounds of energy. The version I am testing is not marketed here in Canada or the US as self defense products but rather as more of a training Paintball Gun.

View fullsize

Starting with my Chronograph velocity test I placed 5 Rubber Balls through my Chronograph using a brand new CO2. The Rubber balls I am going to say are a little bit heavier than standard Paintballs and Umarex claims the Umarex T4E TR50 .50 Caliber Paintball Revolver is capable of hitting around 360 fps so with the heavier rubber balls I was expecting a little bit under the max fps. I was able to get an average of 328 fps so not bad at all.

View fullsize

Moving on to my accuracy test. I need up placing 10 of my 12 rounds into the paper target as I had two rounds that went off in what I am going to call an uncontrolled manor. The 10 rubber paintball rounds that did hit my paper target that was setup 30 feet down range all hit within about 6 inches of each other daily well centered left and right and a little bit low on the target. Gettin back to the uncontrolled shots, I had a situation where I pulled the trigger and the Umarex T4E TR50 .50 Caliber Paintball Revolver went click as you would expect but no CO2 was expelled and so no round was shot. I thought perhaps the cylinder was caught up so I went to wiggle it to try and free it up. As I did so the gun went off without my finger anywhere near the trigger. I am glad I was using rubber balls since the rubber ball hit my cabinet leaning a biota a mark but really causing any damage. This happened twice with the same cylinder, the second time I was bit more prepared for it and had the gun pointed well downrange. I was not able to recreate this problem again so perhaps the cylinder magazine was not seated properly but this still concerns me a bit.

View fullsize

Overall I really like the Umarex T4E TR50 .50 Caliber Paintball Revolver, it’s a pretty cool looking Paintball Gun with decent accuracy and power, you can even feel a little push back and barrel lift when you shoot it. I also like that you can preload a CO2 and puncture it whenever hypo are ready to shoot with a quick smack on the bottom of the grip. Just made sure to put the CO2 in the right way :)

Purchase the T4E TR50 from: The Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

It was a pretty nice day today so I got outside and tested out the Rx Target Systems to see how well it worked shooting my Sig Sauer Virtus PCP .22 Caliber Air Rifle at it for about 50 feet down range.

My systems setup for a more powerful airgun as I was shooting .22 caliber lead pellets with about 11-12 foot pounds of energy. Direct hits passing through the 3/4 inch cut outs had no problem laying down the metal paddles and resetting the paddles was a lot easier than I though it would be even way back 50 feet.

View fullsize

I did not have my Sig Sauer Virtus PCP .22 Caliber Air Rifle perfectly sighted in so I did have to aim low and to the left which made it a bit harder dropping the plates but I did manage to get the job done at least for providing a decent test video fo the Rx Target Systems for the purposes of this video.

Make sure to not only watch my Field Test Shooting video included in this post but also checkout my Rx Target Systems Preview Video where I show it up and close and also go into more details on the Rx Target Systems and how modular and versatile it really is.

We hope to have the Rx Target Systems in our Canada and US Online Replica Airguns stores in the near future but until them you can concat Rx Target Systems at their website.

View fullsize

I want to thank David Bitkowski from Rx Target Systems for providing me with this sample unit to share with the Replica Airguns community. This video is only a Preview video as I wanted to get the RX Target System out there before I follow up with my actual Table Top and Shooting Videos for it.

For now here are some of the key points I want to get out to everyone:

Mission:
Rx Target Systems are meant to bridge the gap between firearms and airguns. They allow high precision shooting on a reactive, three- dimensional, rugged target that can be carted around in a back pack.  What makes Rx Target Systems unique is that it is a system. It is so modular and adaptable with interchangable faceplates and paddles. Rx Target Systems are not going to break or get dented or dissembled on the range as many of the lighter gauged steel targets on the market today vs today’s high powered airguns.

Modular 

• One base allows interchange of faceplates for different target configurations 

• One threaded axel allows interchange of paddle from 10 gauge to 3/8 inch-thick paddles 

Portable 

View fullsize

• Mount it on a shelf indoors 

• Mount it on a sawhorse outdoors  

• Carry it in a backpack or duffle bag- its 10 pounds 

Rugged 

• Solid steel design 

• Faceplates from 10 gauge to ¼ inch thick 

3-Dimensional 

• Faceplate is offset from paddles 

• Clipping the aperture does not guarantee a score 

View fullsize

Intentions of target configurations 

• Standard 1 inch bulls.- represents kill zone of many small game at 30 yards, great for sighting in prior to the hunt. Also is ¼ scale of bull used in rapid fire pistol when shot from 8.3 meters. (25 meters distance/100mm bull) 

• 1.2 inch bulls- represents the 4-10 ring of the NRA 10 meter air rifle target. Gears the shooter to consistently hitting the “black” of that target on paper 

• AAFTA style- represents common kill zones found in American Airgun Field Target Assosciation using 1.5”, 1”, ¾", ½", and 3/8”.  

• WFTF style- represents common kill zones found in World Field Target Federation using 15mm, 25mm, and 38mm apertures 

• 10-15- Inspired by customer request, uses 10mm and 15mm apertures.  High-Precision shooting.

Visit the Rx Target Systems Website

This isn’t a SHOT Show 2020 Interview but most certainly worth reporting on. While walking around SHOT Show I ventured into the Chiappa Booth as I own a .22 caliber 1911 styled pistol from them and they do have some interesting products to take a look at.

View fullsize

Then I saw a red tip on one of their Chiappa Rhino Revolvers which caught my eye since I was not aware that Chiappa was making an Airgun version of their Rhino. Well as it turns out they are hoping to be shipping both an Airsoft version and Steel BB version around spring time and from what I can tell there will be two finishes, a kind of Gold Satin finish and also a Back finish version. As is with a lot of revolvers these days they will be shell loading which will help them look the part of a real steel Chiappa Rhino Revolver.

View fullsize

Looking forward to getting my hands on one when they come out in Spring this year!

View fullsize

Here we go again, another round of SHOT Show videos brought to you direct from Replica Airguns!

As always I like to start off with a Teaser Video with a few quick clips of some of the new products I had the opportunity to take a look at at this years SHOT Show 2020 Las Vegas.

I will be rolling out Interview Videos as quickly as I can edit them and put them together for the following Airgun Related companies:

• Sig Sauer

• Umarex

• Crosman - Velocity Outdoors

• ASG

• Air Venturi

• Chiappa

So sit back and enjoy this years Replica Airguns SHOT Show 2020 Las Vegas Teaser Video!

View fullsize

Type: Paintball Gun.
Manufacturer: Umarex - T4E.
Model: T4E TR50
Materials: Metal & Polymer.
Weight: 726 grams (1.6 pounds).
Barrel: Smooth bore.
Power Source: 1x12 gram CO2.
Action: Revolver - Double action only trigger.
Ammo Type: .50 Caliber Paintball or Rubber Ball.
Ammo Capacity: 6 Rounds x 5 magazines.
FPS: 360.

View fullsize

Trigger Pull: The trigger pull on Umarex T4E TR50 .50 Caliber Paintball Revolver is double action only but not very long with a very different feel than I am use to. The best way to describe it is kind of lumpy, it starts out a bit firm and then eases off a lot just before it releases. Like climbing a hill and then coasting down the otters side. I will have to see how it feels when it’s all loaded up with CO2 and Paintballs and actually shooting at a target.

View fullsize

Accuracy: So far I have not had the opportunity to test the Umarex T4E TR50 .50 Caliber Paintball Revolver out and before I can do so I need to get myself some .50 caliber rubber Paintballs as all I have on hand right now are .43 and .68 caliber paintballs. Stay posted for my Field Test Shooting Video review for the Umarex T4E TR50 .50 Caliber Paintball Revolver.

View fullsize

Build Quality: The build quality of the Umarex T4E TR50 .50 Caliber Paintball Revolver is good overall. It is a mostly plastic build with some metal parts where they need to be internally. It is essentially two plastic halves held together by screws with the few actual mechanical working external parts. You have the trigger with it’s working trigger safety, the removable magazine and magazine release and of course the quick puncture CO2 screw knob. The hammer is internal. The Umarex T4E TR50 .50 Caliber Paintball Revolver is not very heavy but it does feel really solid in the hand.

View fullsize

Realism: The Umarex T4E TR50 .50 Caliber Paintball Revolver  is not really a replica of any real steel gun that I know of. It does share a lot of similarities with the Umarex Brodax which is a CO2 BB Revolver. The Umarex T4E TR50 .50 Caliber Paintball Revolver is basically a very modern looking revolver. It is not going to fool anyone up close that you actually have a real steel revolver but then again I don’t think if you are shooting it at anyone they are going to want to get all that close to you :)

Purchase it from: The Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Pros:

• Expected fairly high fps power of 360 with .50 caliber paintballs, a bit too high for your average paintball field but perhaps powerful enough to discourage an intruder?

• Lots of mounting option for accessories like a tac light, laser or other sighting option with it’s upper and lower picatinny rail setup.

• Quick CO2 pierce system so you can leave a CO2 in it ready to go any time with no worries about CO2 leaking out.

• Working Trigger Safety.

• Comes with 5 total magazines you can preload ready for use.

• Super non-complicated design. Once loaded with CO2 and Paintballs all you need to do is hit the CO2 knob and then pull the trigger.

• Build quality feels good, the gun is fairly beefy but not overly heavy or hard to hold.

View fullsize

Cons:

• Mostly all plastic build.

• Sights do not have white dots on them and are not adjustable.

• Do not expect a lot of shots per CO2. Will find out when I do my Field Test Shooting Review.

View fullsize

Comments:

The Umarex T4E TR50 .50 Caliber Paintball Revolver is an interesting Paintball gun, overseas versions are marketed as the HDR50 which stands for “Home Defense Revolver”, while the North American version is marketed as the TR50 or “Training Revolver”. This is mainly because in the Europe most countries are not allowed to own real handguns but can own “Self Defense handguns”. In North America as most people are well aware, in the US real handguns are very easy to obtain and can be used for self defense. Just across the border here in Canada we can not really purposely have on hand anything that we plan to use as a weapon for self defense so the Umarex T4E TR50 .50 Caliber Paintball Revolver is marketed as a Training Revolver. What’s the difference? Not much, our North American 360 fps version is a lot like the 7.5 joule German version in terms of power but you can also get a more powerful 11 joule version in the UK. All that said, the Umarex T4E TR50 .50 Caliber Paintball Revolver at least here in Canada is made and marketed as a Paintball gun but on the field may be too powerful? What you decide to do with it is up to you!

Purchase it from: The Canada Replica Airguns Store or the US Replica Airguns Store

View fullsize

Another Field Test Shooting Video Review coming for the Replica Airguns Sea Can Indoor Airgun Shooting Range! In todays Shooting Review I test out the Schofield No. 3 CO2 BB-Pellet Revolver using both 4.5mm 5/1 grain Steel BB’s and .177 Caliber 6.9 grain Lead Pellets to see how well they perform in velocity and accuracy. As always I use a brand new CO2 for my velocity testing and for reference the temperature during my testing in the Sea Can was 23 degrees Celsius or 73 degrees Fahrenheit. For my accuracy portion of the shooting test I use a rested and seated shooting position shot 30 feet away from my fresh paper targets.

View fullsize

Starting off with the velocity or power potion of my Field Test Shooting Video for the Schofield No. 3 CO2 BB-Pellet Revolver. I first used the 4.5mm Steel BB shells and shot 3 rounds through my Chronograph averaging 369 fps. I then loaded up the Schofield No. 3 CO2 BB-Pellet Revolver with pellet shells and again placed three .177 caliber lead pellets through my Chrony and got a very similar result with an average of 361 fps. Keep in mind the lead pellets where 6.9 grain versus the steel BB’s at only 5.1 grain, so the lead pellets will be carrying more raw energy at the point of impact even though they where going just a tad bit slower than the steel BB’s.

View fullsize

In terms of accuracy both rounds performed about the same shooting at my paper target 30 feet away. Since the Schofield No. 3 CO2 BB-Pellet Revolver has a 6 round cylinder I shot 6 sounds for each test, 6 steel BB’s and then 6 lead pellets. I also changed the targets for each type of ammo between reloading. I found the Schofield No. 3 CO2 BB-Pellet Revolver shot fairly close to the bullseye, l but with both the Steel BB’s and lead pellets I got one outlier that spread out my groupings significantly, the other 5 rounds where all close being about 2 inches apart? Perhaps it was a bad or misshaped round, or maybe even me ;) I did notice the lead pellets seemed to have a really nice 4 round group out of the 6 that all fell within the bullseye. Hard to really say if BB’s or pellets performed better than the other one at least in my testing.

View fullsize

Overall the Schofield No. 3 CO2 BB-Pellet Revolver shot well for me, the trigger is nice and short and light making placing your shots easy, of course since it is a single action only trigger you kind of need to reset yourself between every shot which can effect groupings just a bit. Since the barrel is not rifled with no danger of damaging the rifling, you can really shoot what ever ammo type you feel like shooting or have on hand and since Schofield No. 3 CO2 BB-Pellet Revolvers get about the same speed and accuracy then it really doesn’t matter that much at the end of the day!

• Buy the Schofield No. 3 CO2 BB-Pellet Revolver in Canada:

• Buy the Schofield No. 3 CO2 BB-Pellet Revolver in the US:

View fullsize

Type: BB/Pellet air revolver.
Manufacturer/Distributor: Bear River.
Model: Schofield No. 3
Materials: Mostly metal with plastic grips.
Weight: 2.4 pounds. (1089 grams)
Barrel: 7 inch (178mm) smooth bore barrel.
Propulsion: 12 gram CO2.
Action: Revolver, single action only.
Ammunition Type: 4.5mm steel BB's and .177 Cal. Pellets.
Ammunition Capacity: 6 rounds.
FPS: 445fps.

View fullsize

Trigger Pull: The trigger pull on the single action only Schofield No. 3 CO2 BB-Pellet Revolver is what you would expect from a pistol of this design. Like the Colt Single Action Army the trigger pull is very short, light and crips, perfect for taking your time and getting a precise shot on target. You will of course have to cock the hammer manually before each shot ao no real action shooting.

View fullsize

Accuracy: I have not tested the Schofield No. 3 CO2 BB-Pellet Revolver in the Replica Airguns Sea Can Indoor Airgun Range but plan to get to it shortly. I will test out both 4.5mm Steel BB’s and some .177 caliber lead Pellets and see how the different ammo types effect both power and accuracy. Keep in mind the Schofield No. 3 CO2 BB-Pellet Revolver has a smooth bore barrel but I am pretty sure pellets will still perform well at 30 feet away.

View fullsize

Build Quality: The Schofield No. 3 CO2 BB-Pellet Revolver is built a lot like the Webley MK VI .455 CO2 Shell Loading Revolver line, perhaps even made in the same factory in Taiwan? The Schofield No. 3 CO2 BB-Pellet Revolver is pretty much an all metal construction other than the plastic grips and any internal seals. The fit and finish is excellent with a great overall weight in the hand. The pistol grips is a lot like what you have with the Colt Single Action Army pistol but the Schofield No. 3 CO2 BB-Pellet Revolver is a lot more front end heavy because of its beefy barrel.

View fullsize

Realism: In terms of replicating a real steel Schofield No. 3 CO2 BB-Pellet Revolver for sure looks and feels that part. The reassessed barrel and well hidden CO2 screw don’t give anything away that the Airgun version is not the real deal. But as with all of these shell loading Airgun Revolvers, the shells are actually closer to a .380 Caliber in diameter rather than a 45 which is what the real steel Schofield No. 3 CO2 BB-Pellet Revolver would be designed for.

Available in the: Replica Airguns Store

View fullsize

Pros:

• If you are like a bulky revolver with good weight to it then the Bear River Schofield No. 3 is it.

• Can shoot Steel BB’s or Pellets since it comers with both shell types.

• Recessed barrel.

• Well concealed CO2.

• Shell loading design that loads from the back so no need to remove shells if you wish not to.

• Single Action Only hammer and trigger action feel good, nice and light with short take-up and release.

• Fairly discreet safety location right behind the hammer so easy to get at.

• Super easy to load, pellet shells can even be reloaded with shells in the gun if you are using the pellet shells.

• Really like the Nickel Finish on this gun.

• Can get simulated Ivory grips for it if you prefer that look.

Cons:

• Sights are not adjustable.

• Warning instructions on side of the frame.

• Barrel is not rifled for pellet use?

• Only a Single Action Only Hammer and Trigger but true to the style of the gun.

View fullsize

Comments:

Yet another classic shell loading CO2 BB Revolver, and again the more the merrier in my option! I like that you get 12 shells with our kit version, 6 removable shells for 4.5mm Steel BB’s and 6 removable shells for .177 caliber Pellets. The Schofield No. 3 CO2 BB-Pellet Revolver is for sure a hefty revolver but the pistol grip is not super large so even people with smaller hands should not have a problem shooting the Schofield No. 3 CO2 BB-Pellet Revolver. The real problem is deciding which Shell Loading Airgun Revolver to buy now since we have so many to choose from… Classic or modern, nickel or black, or perhaps weathered?

My Table Top Review for the Schofield No. 3 CO2 BB/Pellet Revolver:

• Buy the Schofield No. 3 CO2 BB-Pellet Revolver in Canada:

• Buy the Schofield No. 3 CO2 BB-Pellet Revolver in the US:

View fullsize

Here we have three very different products I Unbox and Preview for everyone. A Spring Piston multi-shot .177 Caliber Pellet Rifle, a single action BB/Pellet revolver that’s not a Colt! And a really nice looking Semi Auto Blank Pistol in a Chrome finish.

View fullsize

Let’s start with the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle. I think this is a really well thought out Air Rifle. It’s “almost a Bullpup” in design but it does actually load in front of the trigger just a bit, that said most of the spring piston is behind the trigger setup making it really compact yet with a longer than normal barrel compared to regular Break Barrel Spring Piston Air Rifles. The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle also has a side lever cocking mechanism along with a 5 round auto indexing magazine which makes it much quicker to cock and reload for fast follow-up shots, again compared to a standard Break Barrel Air Rifle, not to mention no barrel droop! The Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle has a claimed fps of up to 500 so we are getting the max amount of velocity possible for our Canadian laws without making it a regulated firearm and requiring a PAL license. And by the way the Air Venturi TR5 Spring Piston 5-shot .177 Caliber Pellet Rifle does come in both a Lime Green and all Black version just in case you are not a fan of the Lime Green finish I show in this video.

View fullsize

Moving onto the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica, if you like single action revolvers then take a look at the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica. It’s a lot more bulky than a Colt Single Action Revolver and also has that top Break design that makes reloading quick and easy. The version we are selling inner Replica Airgun Online Store is the kit version that comes with 6 BB shells and 6 pellet shells so you can take your pick on ammo types. The barrel is not rifled so Steel BB’s will not hurt the Airgun and since pellets are skirted they do not need a rifled barrel to fly straight and true. You can expect around 445 fps for the Schofield No. 3 BB/Pellet 6 Shot Revolver Replica.

View fullsize

Last up is one of my favorite Blank firing Semi Auto Pistols which I have already full reviews in the all Black version so checkout those Video Reviews for more info on the ROHM RG-88 line of Front Firing 9mm Blank Pistols. All I really wanted to show you guys with the ROHM RG-88 9mm PAK Blank Pistol in Polished Chrome is how awesome it looked with the Polished Chrome finish and that we do have more choices now than we use to have in terms of what finish you can get your ROHM RG-88 in. Personally I like the Polished Chrome finish the best but you can also get it in all Black and Matte Chrome, so you decide which one you like the best.

View fullsize

I don’t do a lot of paintball gun reviews, they just don’t come across my table all that often so it’s a lot fo fun when I do get the chance to shoot some beefier caliber ammunition in the Replica Airguns Sea Can Indoor Airgun Shooting Range. Of course I use rubber ball ammo rather than standard paintball rounds in order to keep the mess to a minimum.

I have not done my Table Top YouTube Video Review yet for the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun but you can checkout a Preview Video for now. In Summary the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a pretty much exactly what the name says. It’s basically a sawn off pistol grip styled double barrel shotgun that uses CO2 and shoots .68 caliber paintballs. You have a selector for shooting either out of the left or right barrel or if you want to can even both at the same time but this really slows down the fps so I would not advise it with the 200 fps version that I was testing with.

View fullsize

Now on to the actual testing of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun! As alway I like to find out how close to the factory claimed fps I will get. Umarex claims around 200 fps for this version which is around 7.5 Joules of energy, apparently there is a 16 Joules version that shoots closer to 300 fps but we do not carry it at least right now. I put a couple fo rounds through my Umarex T4E HDS Double Barrel CO2 Paintball Shotgun using rubber ball paintballs which will be a little bit heavier than a standard paintballs and my first shot yielded 180 fps, my second shot was slightly higher at 184 fps so pretty close to the claimed 200 fps and that was in not the warmest of environments since the temperature in the Replica Airguns Sea Can Indoor Airgun Shooting Range was only 16 Degrees Celsius (60 Degrees Fahrenheit).

View fullsize

Next up it was time to see how the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun performed shooting at a target setup 30 feet away. Since there are no actual sights on the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun I had to kind eyeball it and as I shot it more and more I was able to get my shots closer to the center of the target. The Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is not a tac driver but at 30 feet out you should be able to hit an 8-10 inch target pretty consistently. I don’t recommend using the double shot option since the same amount of CO2 is applied to both rounds that would normally be applied to one round decreasing the fps by about half making the paintball rounds shoot a lot slower and not really being that effective. This may be an option with the higher 300 fps version of the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun.

So all in all I had a lot of fun shooting the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun, it’s kind of like a big boy Nerf Gun that you can take onto the paintball field if you wanted to. For home defense I think it is a bit underpowered but there may be a little bit of shock factor that could slow someone down or deter them enough to either give you time get away or take shelter somewhere safe. Maybe using the pepper rounds would work OK in this situation? Either way the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun is a really cool and unique CO2 Airgun that is not overly expensive and a welcome addition to any Airgun enthusiasts collection.

• Buy the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun in Canada

• Buy the Umarex T4E HDS Double Barrel CO2 Paintball Shotgun in the US